Tomoloo H3 User manual

Tomoloo H3
User Manual • Uživatelský manuál •
Užívateľský manuál • Használati utasítás •
Benutzerhandbuch

2
English
3 –27
Čeština
28 –52
Slovenčina
53 –78
Magyar
79 –104
Deutsch
105 –131

3
Dear customer,
Thank you for purchasing our product. Please read the following instructions carefully
before first use and keep this user manual for future reference. Pay particular attention
to the safety instructions. If you have any questions or comments about the device,
please contact the customer line.
󲐜󲐝󲐞󲐟󲐠www.alza.co.uk/kontakt
✆[phone]
Importer Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Praha 7, www.alza.cz

4
About the Manual
This manual is applicable to three-wheel electric skateboard, please read the manual
carefully to:
1. Quickly master the basic operation steps and riding methods of the three-wheel
electric skateboard.
2. Get familiar with the safety riding rules to have a safe and pleasant riding experience.
3. Understand the structure and operation of the skateboard, and regular maintenance
methods of the three-wheel electric skateboard.
If you have any questions or need more information, please contact the franchised deal
or after-sales service.
Please pay attention to the following signs and relating content:
Dangers!
Could cause serious
property damage or
personal injury
Warnings!
Improper operations can
lead to malfunction of the
product.
Information tips
About the skateboard
The three-wheel electric skateboard
The three-wheel electric skateboard uses remote control and ESC speed controller. Rider
stands on the electric skateboard to operate direction by gravity control and change
your speed by remote. This product will be suitable for entertainment and short
journey.

5
The structure diagram of the board
Top View:
Digital display screen
Headlights
Decorative lamp
Tailight

6
Bottom View:
Motor
Battery box lock
USB Port
Charging port
Battery box
Handle
Taillight
Lamp Switch
Power Switch

7
Motor
Frosted pedal
Driven Wheel
Headlight
Dashboard
LED Light
Stop Lamp
Dashboard
LED Light
Fender
Motor
Taillight
Hand Pull Rod
Frosted Pedal
Steering Gear
(Exclusive Patents)

8
The Specification Parameter of the Board
Speed Mode
Low speed 6,2 mph; Middle speed 10 mph; High
speed 15,5 mph
Motor rated power
250 W
Motor type
Permanent magnetic DC brushless motor
Battery voltage/capacity
36 V/4800 MAH
Endurance Mileage
7,5 –9,3 miles, Depends on the user’s weight and the
road condition
Tire Size
6-inch solid tire
Max Load
220 lbs
Incline capacity
15°
Brake
Electric brake by remote control and mechanical
pedal brake
Board height
4,3 inches
USB 2.0
USB 2.0 Output 5 V and mechanical pedal brake
Board size
Length 3,14 inches; Width 1,04 inches; Height
0,72 inches
Board weight
24 lbs
Charging time
(42 V-2 A input) About 3-3,5 hours
The Sketch Map of Remote
Throttle scroll wheel for accelerating or braking
Forward / Backward Button C
Board power indicator
Signal indicator
Remote power indicator
Button A / Power
switch
Button B for changing gears
USB port

9
Remote Control Specification Parameter
Model
Remote for Skateboard H3
Battery Voltage / capacity
3,7 V / 400 MAH
Charging port
Micro USB
Charging time
1 hour
Communication mode
2,4 G
Remote control distance
131 ft (Open field)
Weight
55 g
Controller
ESC-Skateboard-H3
Function and Operation
Power On
With the remote powered off, press the “Button A" (on the remote) for 1 second, the
remote vibrates a short vibration, enters the connecting mode, and the signal LED starts
to flash Red slowly (once a second).
With the board powered off. short press the “Power” button on the board for 0,2
seconds to enter the "connecting" mode, and the Red LED on it starts to flash slowly
(once a second).
Note: the signal light of the remote and the light on the board will turn on after they are
connected,
Power Off
Power off manually: (with the remote and the board powered on), pressing the “Button
A” on the remote for 2 seconds to turn off the remote, which will vibrate a short
vibration after the press; pressing the “Power” button on the board for 1 second to turn
off the board.
Note: If the remote is still on after the board is turned off, the signal light in the remote
will flash red slowly and vibrate once to remind the user. Similarly, if the board is still on
after the remote is powered off, the Red LED on the board will flash slowly (to warn the
user.)
(Power off) Automatically: If the user lets the board stay still with no further operation
for 5 minutes, then the remote and the board will turn off automatically.

10
Connecting and Binding
(With the remote and the board power-off) Press the “Power” button of the board for 5
seconds, the Red light of it starts to flash rapidly to indicate that the board enters the
binding mode; then press the “Button A” on the remote for 5 seconds, the Signal light on
it starts to flash Red rapidly to indicate that the remote enters the binding mode, and
the remote vibrates two short vibrations and one long vibration to indicate that the
biding succeeds. The signal light on the remote and the Red LED on the board turn on
when the binding succeeds.
Note: When using a new remote and a new board, there is no need to press either the
Power button on the board or the Button A on the remote, they enter into the binding
mode when they are turned on.
Battery Indicator
Remote Power indicator (a single light)
When the remote is turned on, if it detects the power is less then 25%, which can barely
support a one-hour operation, the Remote power light turns Red; if the power is more
than 25%, which can support operation of at least one hour, the Remote Power light will
be green.
If there is only 5 of power, which can only support a 15-minute operation, the remote
will vibrate a double, long vibration (vibrate for 0,5 seconds, pause for 0,5 seconds and
then vibrate again for 0,5 seconds) and starts to flash Red slowly (once a second); if
there is only 2,5% of power left, the remote will vibrate a double, long-vibration again as
the same as previous and starts to flash Red light slowly; and if the power is below the
regulated value (3,4 V) for safe use and use and the boards stops. The remote will
vibrate a short vibration and turn off automatically.
Board power indicator (4 lights in a row)
One light turns on to indicate that 25% of power is left, one light flashes to indicate that
12.5% of power is left. For example, if the power is from 62.5% to 75%, the lights will be “
”if the power is from 50%-62.5%, the lights will be “ ”; if the power is
below 25%, the remote will vibrate a double, long vibration and the lights will be in “
”; if the power is below 12.5%, the remote will vibrate a double, long vibration
and the lights will be “ ”; and if the voltage goes below the safety value, the
power output will be stopped. For this situation, you have to stop using as soon as
possible.
Notes: the remote will display the power of the remote and the board for 2 seconds and
then stop when it's powered on and connected to the board. Press the Button A at any
time can re-trigger the display of the power of the remote and the board. the remote
only displays the power of the remote when the board is not connected (to the remote).
Attention: “ ” means “solid”; “ ” means “flash”; “ ” means “die out”.

11
Accelerograph and brakes
User can move the “throttle scroll wheel” forward to speed up and move it backward to
brake.
Notes: Do not move the “throttle scroll wheel” when pressing the Button A (Power
Switch). If you see the four LEDs (on the remote) flash in the following way:
…, then please check
if the “throttle scroll wheel” is at the neutral/zero throttle position.
Switch of direction
When the board is moving forward, if the user moves the button C backward, the
remote will vibrate a single, short vibration (0.1 second), the four LEDs will flash one by
one from front to back to indicate the "Backward mode". When the board is moving
backward, if the user moves the button C forward, the remote will vibrate a single, short
vibration, the four LEDs will flash one by one from back to front to indicate the "Forward
mode".
Note: this operation effects only when the "throttle scroll wheel" is at the neutral
position.
Switch of Gear
The Button B on the remote (as shown in the picture) is for changing gears. In general,
there are three gears available: 1st gear & 2nd gear & 3rd gear. When in 1st gear, if
press the Button B, the remote will vibrate a single, short vibration, the four board
power LEDs will flash one by one (from one end to the other end) rapidly to indicate that
the board is in 2nd gear now. When in 2nd gear, if press the Button B, the remote will
vibrate a single, short vibration, the four board power LEDs will flash one by one (from
one end to the other end) slowly to indicate that the board is in 3rd gear now. When in
2nd gear, if press the Button B, the remote will vibrate a single, short vibration, the four
board power LEDs will flash one by one (from one end to the other end) slowly to
indicate that the board is in 1st gear now.
Note: this operation effects only when the "throttle scroll wheel" is at the neutral
position. The specific gear and speed can be adjusted by the specific ESC the user uses.

12
Charging
Charging the remote: the remote vibrates once after It's connected to a power supply via
the charging cable and the remote power LED comes on Red and turns to Green when
it's fully charged.
Note: the remote cannot be used during the charging, it vibrates a single, short vibration
and powers off automatically after removing the charging cable.
Charging the board battery: with the board powered off, connect it to a power supply via
the charger/adapter, it automatically enters the charging mode, and the four Red board
power LEDs come on; with the board powered on, connect it to a power supply (via the
charger/adapter), it enters the charging mode and the four Red board power LEDs
lighting up. The board will automatically turn off after removing the charger/adapter.
Note: During charging, the board is not connected to the remote or it doesn't function
even if it's connected to the remote. In other words, the motor & ESC on the board stop
functioning during the process.
Fault Warning
Lower Battery Warning
When the remote power is only 5% (for a 15-minute operation), the remote will vibrate a
double, long vibration and the remote power indicator (a LED) will flash Red rapidly;
when the power is only 2.5%, the remote will vibrate a double, long vibration again, and
the LED flashes Red rapidly; and when the voltage goes below the regulated value (3.4V)
and the speed of the skateboard is below 3km/h for safe use, the remote will
automatically turn off.
When the board power is below 25%, the remote will vibrate a double, long vibration
and the board power indicator (4 LEDs) will display in this way " "; when the
power is below 12.5%, the remote will vibrate a double, long vibration and the 4 LEDs
will display in this way " "; and when the voltage goes below the regulated value
for safe use, then there will be no more throttle output and the throttle value will be
automatically and slowly reduced to zero(the process will take no more than 3 seconds).
At this time, any throttle input will not take effect, only brake input works and you can
brake manually. Note: It's better to stop using and charge the corresponding device
when the warning (due to low remote power or board power) is given for the first time.
Otherwise, the LIPO battery will be damaged due to over-discharge.

13
Signal Loss
The remote will vibrate once when losing signals for 0.2 seconds, if the board is during
acceleration, the "throttle scroll wheel" will be back to the neutral position immediately
and automatically, and then brake slowly and automatically; if the board is during
braking, then it will slowly Increase or decrease to a fixed brake force. The remote will
enter the searching board mode when signals are lost, it will vibrate once and stop
braking slowly when it finds one and re-connect to the one successfully, the board can
only resume normal operation after moving the "throttle scroll wheel" to the neutral
position.
Motor Lock-up
When the motors are locked up or stuck, the remote will keep vibrating intermittently
and the board power indicator (4 LEDs) will intermittently flash in this way
…. In that case, please stop
running the board and check if the motor(s) are stuck by foreign objects, remove the
object immediately and then run the board.
Overheat
When the operating temperature of the ESC/motors Is above 100°C or below 0°C, the
remote will vibrate once and the board power indicator (4 LEDs) will intermittently flash
in this way the motor will operate with a reduced
power (about 25% throttle).
Note: The user needs to pay attention to the ESC & motor temperatures. When the
operating temperature of the ESC/motors Is high, rider needs to find reason, and use
the skateboard only until problems solved.
Short-circuit
When the ESC detects an ESC or motor short-circuit issue, the remote signal LED will
flash intermittently in this way … the
motor will stop operating.
Note: Power off the board and then turn it on, use it after the problem is solved.

14
Overcharge (when going downhill with a fully charged battery)
In principle, going downhill with a fully charged battery is prohibited, because the
battery will be charged when braking during the going-downhill process, so going
downhill with a fully charged can shorten the service life of the board battery or even
cause accidents like an explosion and fire. The user needs to consume some power
before going downhill. If some user violates the rule and goes downhill with a fully
charged battery, the remote will vibrate and the board power Indicator flashes In this
way " ′′ or “ ”when ESC detects the battery voltage is too high. If the user
continues to go downhill, the board will brake automatically to prevent user from doing
that. This method can only protect the battery to a limited extent and cannot 100%
guarantee for the battery safety.
First Use: The Three-Wheel Electric Skateboard
Check the Items in the Box
Please open the packing box and remove the items carefully in turn.
Please check out the items as the following list:
Skateboard
1 PC
User Manual
1 PC
Remote Controller
1 PC
Removal Battery
Key
2 PCS
Charger
1 PC
Recharge cradle
1 PC
Battery Pack
Built-in
Battery Backup
Optional
Charge the battery
First, insert the charger socket to skateboard's charge socket, and then insert the plug of
the charger to the power socket (100~240 v electric supply), then it can be charged.
When the display light on the charger is red, it is charging. When the display light
changed from red to green, the battery is fully charged.
Charge the battery before it runs out completely. When the state dashboard shows in
low battery, please charge your skateboard.

15
USB port
Each electric skateboard has a USB port at the tail. To toggle the band switches to left or
right can output 5V/1A current. At this point, you can charge for mobile phone or other
devices.
The USB port is only useful in the case of your skateboard turning on, and USB port is as
power supply only, no related to data transmission.
Please don't insert devices whose current demand is higher than 1A.
Bluetooth music
The Skateboards come standard with Bluetooth music playback.
You can use a smart mobile device to connect the Bluetooth speaker of a skateboard by
pressing the button to turn on the Bluetooth and turning on the Bluetooth of the mobile
device. After the pairing is successful, you can enjoy music by balancing the Bluetooth
speakers on the skateboard.
Application
You can also download and install the mobile app for skateboard, view the driving track,
and share and interact with other riders online. Please download the App from either
the App Store or download the App from the Google Play Store.

16
Dashboard
1. Bluetooth-To connect your skateboard through Bluetooth on your smart phone, press
"Connect". If your skateboard is already paired, this part of the screen will show
"Connected" in blue.
2. Settings - Press the gear icon to adjust settings.
3. Speed - The digital speedometer displays your speed in kms per hour.
4. Battery - The percentage displays the remaining battery life of your skateboard.
5. Enjoy - Operation Tips.
6. Sports - Enter the sports mode.
7. Friends-This function can help you add your friends who also have "TOMOLOO
skateboard ", and you can review
his/her recent games in his/her page.
8. Home - Back to home page.
9. Challenge-You can PK your friends who also have "TOMOLOO skateboard" in this
Mode.
10. More - Display more information.
Setting
Press the gear icon to change settings for your skateboard.
•Switch - Switch speed between MPH/KMH.
•Information - System information of skateboard
•Self-check - System self-check information
Digital Display Information
The information that the digital display can check:
Total vehicle mileage
Current speed
Current battery charge ratio
Speed gear
App Bluetooth connection status

17
Using the Three-Wheel Electric Skateboard for the First
Time
From development to production, each three-wheel electric skateboard had
experienced strictly quality control. However, if we don't follow the safe riding rules,
there will also be a security risk. At the same time, we must remind you that once the
skateboard go on roads or public areas, even if you fully comply with the safe riding
specifications, it is also likely to face risk caused by others' illegal riding or improper
operation
Warning:
Please strictly abide by the contents of this chapter. We will not be responsible for any
property and personal loss, accident, legal disputes, and any other events Involved In
Interest conflicts which caused by violation of the Guides for Safe Riding.
Regulation
Understand and strictly abide by the local traffic laws and regulations.
Please take effective safety measures before riding. Wear an examined helmet which is
suitable for your head, equipped with a belt, and able to protect the back of your head.
According to the past experience, riders should wear gloves, eyes equipment, waist
support, kneecap and other protecting equipment.
Before riding, make sure that you are in good condition and sober without taking in
wine, sedative, or stimulant at least 6 hours before. When you are unwell or cannot
comply with the instructions or warnings of this manual, please do not ride.
Check before you are riding each time, make sure that all the exposed parts without
looseness, drops, damage, and no unknown or warning ring when you are riding. Before
the fault has not been ruled out, do not ride.
Check the power after starting up, when shortage, please don't ride for long distance.
When it was at low power and continue to issue warning ring, please get off and charge
in time to ensure your safety.
Maintain appropriate alert when you are riding and keep reasonable safety distance
with pedestrians or other vehicles.
When share your vehicle with others, please ensure that they have read this manual
carefully.

18
Please use the recommended storage bag, side locker, or carry a backpack to carry
items. Don't put any items on the pedals. The total load weight of the Joystick should not
be heavier than 1 kg, otherwise It will affect the body's balance.
Before moving the intelligence balancing vehicle, please make sure that the power has
been closed. Otherwise, the tyres will quickly rotate, it may cause damage.
Please maintain and repair the vehicle regularly.
Prohibitions
Don't use the skateboard in areas where were prohibited to enter by laws and rules of
the countries, regions, and management units.
No riding on risky and uncomfortable occasions, such as deep pit or cracks, slope more
than 15 degrees, water deeper than 3 cm.
Don't ride on motorways. In some countries and regions, non-motorways also do not
allow such vehicle, please refer to local regulations.
No riding in unsafe environment, such as places where storing Inflammable and
explosive gas, steam, liquid, dust, fibre that may cause fire or explosion events.
• No riding in heavy rain, snow, icy road, water, wet soil road or other bad weather or
road conditions
It is forbidden for children less than 14 years old and men more than 60 years old to
ride alone, they must be ride with the help of family carers. It is forbidden for pregnant
women, alcoholics, mental patients, heart patients, limited mobility persons (such as the
disabled) to ride.
It is forbidden for two or more persons standing on vehicle or carry others to ride,
especially ban to carry or hold Infants.
Don't let your two hands leave the joystick at the same time.
No making and receiving calls or making other behaves that will lead to distraction while
riding.
Don't lean on joystick or handle, otherwise you might be hurt accidentally. When driving,
please be sure to keep at least one punch between your body and Joystick (or handle).
No riding up and down on stairs, don't empty out in any case (such as cross obstacles at
high speed). No straddling on the shoulder of the road by one wheel and riding on the
stairs.
No retreating and turning back at high speed. No lateral riding in slopes.
It is forbidden for violate other provisions in this manual, especially contents in the
"dangers" and "warnings" projects.

19
Safe/Civil Driving Considerations
Please take the initiative to understand and comply with local traffic regulations before
driving.
Please drive in a civilized manner, maintain a safe distance from pedestrians and
vehicles, avoid collisions, and prepare to park at any time.
When you drive a skateboard, the height will be more than 10cm higher than when
walking. When passing through a door frame or near a doorway, tree branches, various
signs, or other relatively low overhead obstacles, be alert and avoid collisions with your
head.
Please keep your body relaxed while driving and use your knees and elbows to gently
bend and raise your head in a relaxed position.
Avoid sudden acceleration and sudden deceleration.
Give courtesy to pedestrians. Avoid scaring pedestrians, especially children. When
passing from behind the pedestrian, the pedestrian is reminded and decelerates as it
passes. When face to face with pedestrians, pay attention to maintaining a safe distance
and reducing speed.
It is very dangerous to travel at high speed in the crowd. When crossing the crowd, be
sure to slow down and pass at the same speed as the pedestrian. There is plenty of
room to pass pedestrians when it is safe to pass.
When traveling with other skateboard drivers, maintain an appropriate safety distance,
avoid dangers and obstacles, and try not to ride side by side.
Driving backward is very dangerous. Try to avoid running backwards unless you can
slowly back down a few steps in order to avoid obstacles.
Try to avoid driving in poor lighting conditions. At this time, you should reduce the
speed, keep vigilant, and confirm that the light is good and the line of sight Is clear.
Do not stop the skateboards in a place that will block pedestrians.

20
Riding the Three-Wheel Electric Skateboard
Preparations
Choose an empty flat field, both indoor and outdoor are available, not smooth, and
slippery ground, no motor vehicles, bicycles, pets, children, or other objects that will lead
to distraction.
You need to read this manual, familiar with the safety standards and cautions before
riding this skateboard.
Wear helmet and other protective equipment to avoid possible injuries.
Move the Skateboard to the centre of the field.
Start up Your Skateboard
Press the power button of the front of the skateboard to start, indicator light begins to
flash, and then press the power button of the remote control, the indicator light is
always being on means It Is successful to start.
Warning:
If this is your first-time play skateboard, don't get on the skateboard in a rush, following
steps below to assure your safety.
Precautions Before Riding
After power on, get familiar with the basic functions of the remote control before play
skateboard. Familiarity with go forward, brake, switch shift, and battery indicating
function, adjust the remote controller to the low speed and ready to get on the
skateboard.
If the power is turn off, you can only use it as unpowered skateboard.