Toro 72201 User manual

Operator’s Manual
Domestic English (EN)
Form No. 3328–112
417XT and 419XT
Wheel HorseGarden Tractor
Model No. 72201—Serial No. 230000001 and Up
Model No. 72202—Serial No. 230000001 and Up

2
All Rights Reserved
Printed in the USA
2003 by The Toro Company
8111 Lyndale Avenue South
Bloomington, MN 55420-1196
CALIFORNIA
Proposition 65 Warning
The engine exhaust from this product contains
chemicals known to the State of California to
cause cancer, birth defects, or other reproductive
harm.
Warning
The enclosed Engine Owner’s Manual is supplied for
information regarding The U.S. Environmental
Protection Agency (EPA) and the California Emission
Control Regulation of emission systems, maintenance
and warranty.
Keep this engine Owner’s Manual with your unit.
Should this engine Owner’s Manual become damaged
or illegible, replace immediately. Replacements may be
ordered through the engine manufacturer.
This spark ignition system complies with Canadian
ICES–002.
Ce système d’allumage par étincelle de véhicule est
conforme à la norme NMB–002 du Canada.
Contents
Page
Introduction 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safe Operating Practices 3. . . . . . . . . . . . . . . . . . .
Toro Riding Mower Safety 5. . . . . . . . . . . . . . . . .
Slope Chart 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety and Instruction Decals 9. . . . . . . . . . . . . . .
Gasoline and Oil 12. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recommended Gasoline 12. . . . . . . . . . . . . . . . . . .
Using Stabilizer/Conditioner 12. . . . . . . . . . . . . . . .
Filling the Fuel Tank 12. . . . . . . . . . . . . . . . . . . . . .
Check Engine Oil Level 12. . . . . . . . . . . . . . . . . . . .
Setup 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Loose Parts 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checking the Tire Pressure 13. . . . . . . . . . . . . . . . .
Activating and Installing the Battery 13. . . . . . . . . .
Checking the Engine Oil 14. . . . . . . . . . . . . . . . . . .
Checking the Tractor Lubrication 14. . . . . . . . . . . .
Learn to Operate the Tractor 14. . . . . . . . . . . . . . . .
Test Driving the Tractor 14. . . . . . . . . . . . . . . . . . . .
Checking the Safety System 14. . . . . . . . . . . . . . . .
Operation 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Think Safety First 15. . . . . . . . . . . . . . . . . . . . . . . .
Controls for Model 72201 15. . . . . . . . . . . . . . . . . .
Page
Controls for Model 72202 15. . . . . . . . . . . . . . . . . .
Operating the Parking Brake 15. . . . . . . . . . . . . . . .
Starting and Stopping the Engine 16. . . . . . . . . . . .
Operating the Power Take Off (PTO) 17. . . . . . . . .
The Safety Interlock System 17. . . . . . . . . . . . . . . .
Indicator Control Module 19. . . . . . . . . . . . . . . . . .
Driving Forward or Backward 19. . . . . . . . . . . . . . .
Stopping the Machine 20. . . . . . . . . . . . . . . . . . . . .
Using the Attachment Power Lift 20. . . . . . . . . . . .
Operating the Attachment Lift Lever 20. . . . . . . . .
Positioning the Seat 21. . . . . . . . . . . . . . . . . . . . . . .
Headlights 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Positioning the Tilt Steering Wheel 21. . . . . . . . . . .
Using the Cruise Control 21. . . . . . . . . . . . . . . . . . .
Pushing the Machine by Hand 22. . . . . . . . . . . . . . .
Maintenance 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recommended Maintenance Schedule 23. . . . . . . .
Servicing the Engine Oil 24. . . . . . . . . . . . . . . . . . .
Cleaning the Cooling System 25. . . . . . . . . . . . . . .
Servicing the Air Cleaner 25. . . . . . . . . . . . . . . . . .
Servicing the Spark Plug 26. . . . . . . . . . . . . . . . . . .
Greasing and Lubrication 27. . . . . . . . . . . . . . . . . . .
Checking the Tire Pressure 28. . . . . . . . . . . . . . . . .
Servicing the Brake 28. . . . . . . . . . . . . . . . . . . . . . .
Servicing the Fuel Tank 28. . . . . . . . . . . . . . . . . . . .
Servicing the Fuel Filter 29. . . . . . . . . . . . . . . . . . .
Servicing the Front Wheel Toe-In 29. . . . . . . . . . . .
Transaxle Fluid 30. . . . . . . . . . . . . . . . . . . . . . . . . .
Servicing the Fuses 30. . . . . . . . . . . . . . . . . . . . . . .
Servicing the Headlights 30. . . . . . . . . . . . . . . . . . .
Servicing the Battery 31. . . . . . . . . . . . . . . . . . . . . .
Wiring Schematic 34. . . . . . . . . . . . . . . . . . . . . . . . .
Wiring Schematic 35. . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning and Storage 36. . . . . . . . . . . . . . . . . . . . . .
Troubleshooting 37. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The Toro Total Coverage Guarantee 40. . . . . . . . . . . . .
Introduction
Important The engine in this product is not equipped
with a spark arrester muffler. It is a violation of California
Public Resource Code Section 4442 to use or operate this
engine on any forest-covered, brush-covered, or
grass-covered land as defined in CPRC 4126. Other states
or federal areas may have similar laws.
Thank you for purchasing a Toro product.

3
All of us at Toro want you to be completely satisfied with
your new product, so feel free to contact your local
Authorized Service Dealer for help with service, genuine
replacement parts, or other information you may require.
Whenever you contact your Authorized Service Dealer or
the factory, always know the model and serial numbers of
your product. These numbers will help the Service Dealer
or Service Representative provide exact information about
your specific product. You will find the model and serial
number plate at the location shown in Figure 1.
1
m–2345
Figure 1
1. Modeland serial number plate
For your convenience, write the product model and serial
numbers in the space below.
Model No:
Serial No.
Read this manual carefully to learn how to operate and
maintain your product correctly. Reading this manual will
help you and others avoid personal injury and damage to
the product. Although we design, produce and market
safe, state-of-the-art products, you are responsible for
using the product properly and safely. You are also
responsible for training persons, who you allow to use the
product, about safe operation.
The warning system in this manual identifies potential
hazards and has special safety messages that help you and
others avoid personal injury, even death. Danger,
Warning, and Caution are signal words used to identify
the level of hazard. However, regardless of the hazard, be
extremely careful.
Danger signals an extreme hazard that will cause serious
injury or death if the recommended precautions are not
followed.
Warning signals a hazard that may cause serious injury or
death if the recommended precautions are not followed.
Caution signals a hazard that may cause minor or
moderate injury if the recommended precautions are not
followed.
Two other words are also used to highlight information.
Important calls attention to special mechanical
information, and Note emphasizes general information
worthy of special attention.
Determine the left and right side of the machine from the
normal operating position.
Safety
This machine meets or exceeds the B71.1–1998
specifications of the American National Standards
Institute, in effect at the time of production. However,
improper use or maintenance by the operator or owner
can result in injury. To reduce the potential for injury,
comply with these safety instructions and always pay
attention to the safety alert symbol, which means
CAUTION, WARNING, or DANGER—“personal
safety instruction.” Failure to comply with the
instruction may result in personal injury or death.
Safe Operating Practices
The following instructions are from ANSI standard
B71.1—1998.
This product is capable of amputating hands and feet and
throwing objects. Always follow all safety instructions to
avoid serious injury or death.
General Operation
•Read, understand, and follow all instructions in the
operator’s manual and on the machine before starting.
•Allow only responsible adults who are familiar with
the instructions to operate the machine.
•Clear the area of objects such as rocks, toys, wire, etc.,
which could be picked up and thrown by the blade.
•Be sure the area is clear of other people before
mowing. Stop the machine if anyone enters the area.
•Never carry passengers.
•Do not mow in reverse unless absolutely necessary.
Always look down and behind before and while
backing.
•Be aware of the mower discharge direction and do not
point it at anyone. Do not operate the mower without
either the entire grass catcher or the guard in place.
•Slow down before turning.

4
•Never leave a running machine unattended. Always
turn off blades, set parking brake, stop engine, and
remove keys before dismounting.
•Turn off blades when not mowing.
•Stop the engine before removing the grass catcher or
unclogging the chute.
•Mow only in daylight or good artificial light.
•Do not operate the machine while under the influence
of alcohol or drugs.
•Watch for traffic when operating near or crossing
roadways.
•Use extra care when loading or unloading the machine
into a trailer or truck.
•Always wear safety goggles or safety glasses with side
shields when operating mower.
•Data indicates that operators, age 60 years and above,
are involved in a large percentage of riding
mower–related injuries. These operators should
evaluate their ability to operate the riding mower
safely enough to protect themselves and others from
serious injury.
Slope Operation
Slopes are a major factor related to loss-of-control and
tip-over accidents, which can result in severe injury or
death. All slopes require extra caution. If you cannot back
up the slope or if you feel uneasy on it, do not mow it.
•Mow up and down slopes, not across.
•Remove obstacles such as rocks, tree limbs, etc.
•Watch for holes, ruts or bumps. Uneven terrain could
overturn the machine. Tall grass can hide obstacles.
•Use slow speed. Choose a low gear so that you will not
have to stop or shift while on the slope.
•Follow Toro’s recommendations for wheel weight or
counterweights to improve stability.
•Use extra care with grass catchers or other
attachments. These can change the stability of the
machine.
•Keep all movement on slopes slow and gradual. Do
not make sudden changes in speed or direction.
•Avoid starting or stopping on a slope. If tires lose
traction, disengage the blades and proceed slowly
straight down the slope.
•Do not turn on slopes unless necessary, and then, turn
slowly and gradually downhill, if possible.
•Do not mow near drop-offs, ditches, or embankments.
The machine could suddenly turn over if a wheel goes
over the edge of a cliff or ditch, or if an edge caves in.
•Do not mow on wet grass. Reduced traction could
cause sliding.
•Do not try to stabilize the machine by putting your
foot on the ground.
•Do not use a grass catcher on steep slopes.
Children
Tragic accidents can occur if the operator is not alert to
the presence of children. Children are often attracted to
the machine and the mowing activity. Never assume that
children will remain where you last saw them.
•Keep children out of the mowing area and under the
watchful care of another responsible adult.
•Be alert and turn the machine off if children enter the
area.
•Before and while backing, look behind and down for
small children.
•Never carry children, even with the blades off. They
may fall off and be seriously injured or interfere with
safe machine operation.
•Never allow children to operate the machine.
•Use extra care when approaching blind corners,
shrubs, trees, the end of a fence or other objects that
may obscure vision.
Service
•Use extra care when handling gasoline and other fuels.
They are flammable and vapors are explosive.
– Use only an approved container.
– Never remove the gas cap or add fuel when the
engine is running. Allow the engine to cool before
refueling. Do not smoke.
– Never refuel the machine indoors.
– Never store the machine or fuel container inside
where there is an open flame, such as near a water
heater or furnace.
•Never run a machine inside a closed area.
•Keep nuts and bolts tight, especially the blade
attachment bolts. Keep equipment in good condition.
•Never tamper with safety devices. Check their proper
operation regularly.
•Keep the machine free of grass, leaves, or other debris
build-up. Clean up oil or fuel spillage. Allow the
machine to cool before storing.
•Stop and inspect the equipment if you strike an object.
Repair, if necessary, before restarting.

5
•Grass catcher components are subject to wear, damage
and deterioration, which could expose moving parts or
allow objects to be thrown. Frequently check
components and replace with manufacturer’s
recommended parts, when necessary.
•Mower blades are sharp and can cut. Wrap the blade(s)
or wear gloves, and use extra caution when servicing
them.
•Use only genuine Toro replacement parts to ensure that
original standards are maintained.
Toro Riding Mower Safety
The following list contains safety information specific to
Toro products or other safety information that you must
know that is not included in the ANSI standards.
Engine exhaust contains carbon monoxide, which
is an odorless, deadly poison that can kill you. It is
also known to the State of California to cause
birth defects.
Do not run engine indoors or in an enclosed area.
Warning
•Stop the engine, disconnect spark plug wire(s) and
remove key before performing any service, repairs,
maintenance or adjustments.
•Slow down before turning. Sharp turns on any terrain
may cause loss of control.
•Never leave a running machine unattended. Always
turn off blades, set parking brake, stop engine, and
remove the ignition and KeyChoicekeys before
dismounting.
•Keep hands, feet, hair and loose clothing away from
attachment discharge area, underside of mower and
any moving parts while engine is running.
•Do not touch equipment or attachment parts which
may be hot from operation. Allow to cool before
attempting to maintain, adjust or service.
•Battery acid is poisonous and can cause burns. Avoid
contact with skin, eyes and clothing. Protect your face,
eyes and clothing when working with a battery.
•Battery gases can explode. Keep cigarettes, sparks and
flames away from battery.
•Use only genuine replacement parts to ensure that
original standards are maintained.
•Use only Toro approved attachments. Warranty may be
voided if used with unapproved attachments.
•Do not mow across hillsides or slopes greater than 5
degrees.
•Do not mow down hillsides or slopes greater than 15
degrees.
•Do not mow up hillsides or slopes greater than 10
degrees.
•If a steep slope must be ascended, back up the hill, and
drive forward down the hill, keeping the machine in
gear.
•Avoid turning on slopes. If you must turn, turn slowly
and gradually downhill, if possible.
•Do not use a grass catcher on steep slopes. Heavy
grass bags could cause loss of control or overturn the
machine.
•If loading the machine onto a trailer or truck, use a
single, full-width ramp only. The ramp angle should
not exceed 15 degrees.

6

7
Slope Chart

8

9
Safety and Instruction Decals
Safety decals and instructions are easily visible to the operator and are located near any
area of potential danger. Replace any decal that is damaged or lost.
112168
83-6620
93-0302
92-6726
99-2985
99-5339
106-9871 (Model 72202 only)
1. Cruise control, locked
2. Power Take-off (PTO)
3. Battery
4. Engine oil pressure
5. Fuel level
6. Mowing in reverse
enabled.

10
99-8036 (Model 72201 only)
1. Mowingin reverse
enabled.
2. Battery
3. Engine oil pressure
4. Power Take-off (PTO)
92-6720
1. Pull the knob out to start
the PTO. 2. Push the knob in to stop the PTO.
92-6721
104-4163
1. Explosion hazard
2. No fire, open flames, or
smoking.
3. Caustic liquid/chemical
burn hazard
4. Wear eye protection
5. Read the Operator’s
Manual.
6. Keep bystanders a safe
distance from the battery.

11
104-5091
1. Contains lead; do not
discard.
2. Recycle
3. Wear eye protection;
explosive gases can cause
blindness and other injuries
4. No sparks, flame, or smoking
5. Sulfuric acid can cause
blindness or severe burns.
6. Flush eyes immediately with
water and get medical help
fast.
7. Maximum fill line
8. Minimum fill line
9. Instructions for activating the
battery

12
Gasoline and Oil
Recommended Gasoline
Use UNLEADED Regular Gasoline suitable for
automotive use (85 pump octane minimum). Leaded
regular gasoline may be used if unleaded regular is not
available.
Important Never use methanol, gasoline containing
methanol, or gasohol containing more than 10% ethanol
because the fuel system could be damaged. Do not mix oil
with gasoline.
Danger
In certain conditions, gasoline is extremely
flammable and highly explosive. A fire or
explosion from gasoline can burn you and others
and can damage property.
•Fill the fuel tank outdoors, in an open area,
when the engine is cold. Wipe up any gasoline
that spills.
•Never fill the fuel tank inside an enclosed
trailer.
•Do not fill the fuel tank completely full. Add
gasoline to the fuel tank until the level is 1/4 to
1/2 inch (6 to 13 mm) below the bottom of the
filler neck. This empty space in the tank allows
gasoline to expand.
•Never smoke when handling gasoline, and stay
away from an open flame or where gasoline
fumes may be ignited by a spark.
•Store gasoline in an approved container and
keep it out of the reach of children. Never buy
more than a 30-day supply of gasoline.
•Always place gasoline containers on the ground
away from your vehicle before filling.
•Do not fill gasoline containers inside a vehicle
or on a truck or trailer bed because interior
carpets or plastic truck bed liners may insulate
the container and slow the loss of any static
charge.
•When practical, remove gas–powered
equipment from the truck or trailer and refuel
the equipment with its wheels on the ground.
•If this is not possible, then refuel such
equipment on a truck or trailer from a portable
container, rather than from a gasoline
dispenser nozzle.
•If a gasoline dispenser nozzle must be used,
keep the nozzle in contact with the rim of the
fuel tank or container opening at all times until
fueling is complete.
Gasoline is harmful or fatal if swallowed.
Long–term exposure to vapors can cause serious
injury and illness.
•Avoid prolonged breathing of vapors.
•Keep face away from nozzle and gas tank or
conditioner opening.
•Keep gas away from eyes and skin.
Warning
Using Stabilizer/Conditioner
Use a fuel stabilizer/conditioner in the machine to provide
the following benefits:
•Keeps gasoline fresh during storage of 90 days or less.
For longer storage it is recommended that the fuel tank
be drained.
•Cleans the engine while it runs
•Eliminates gum-like varnish buildup in the fuel
system, which causes hard starting
Important Do not use fuel additives containing
methanol or ethanol.
Add the correct amount of gas stabilizer/conditioner to the
gas.
Note: A fuel stabilizer/conditioner is most effective when
mixed with fresh gasoline. To minimize the chance of
varnish deposits in the fuel system, use fuel stabilizer at
all times.
Filling the Fuel Tank
1. Shut the engine off and set the parking brake.
2. Clean around fuel tank cap and remove the cap. Add
unleaded regular gasoline to fuel tank, until the level is
1/4 to 1/2 inch (6 to 13 mm) below the bottom of the
filler neck. This space in the tank allows gasoline to
expand. Do not fill the fuel tank completely full.
3. Install fuel tank cap securely. Wipe up any gasoline
that may have spilled.
Check Engine Oil Level
Before you start the engine and use the machine, check
the oil level in the engine crankcase; refer to Checking the
Engine Oil Level, page 24.

13
Setup
Note: Determine the left and right sides of the machine
from the normal operating position.
Loose Parts
Note: Use the chart below to verify all parts have been shipped.
Description Qty. Use
Bolt, 1/4 x 3/4 inch
Hex Nut, 1/4 inch
2
2Activating and installing the battery
Key 1Use in ignition switch.
Operator’s Manual
Riding Mower Safety Video
1
1
Read before operating tractor
View before operating tractor
Checking the Tire Pressure
Refer to Checking the Tire Pressure on page 28. Check the
front and rear tire pressure. The recommended front and
rear tire pressure is 20 psi (83 kPa).
Activating and Installing the
Battery
Bulk electrolyte with 1.265 specific gravity must be
purchased from a local battery supply outlet.
Danger
Battery electrolyte contains sulfuric acid which is
a deadly poison and causes severe burns.
•Do not drink electrolyte and avoid contact with
skin, eyes or clothing. Wear safety glasses to
shield your eyes and robber gloves to protect
your hands.
•Fill the battery where clean water is always
available for flushing the skin.
•Follow all instructions and comply with all
safety messages on the electrolyte container.
1. Remove the battery from the tractor.
2. Clean the top of the battery with a paper towel.
Note: Never fill the battery with electrolyte while the
battery installed in the tractor. Electrolyte could be spilled
on other parts and cause corrosion.
3. Remove the vent caps from the battery (Fig. 2).
4. Slowly pour electrolyte into each battery cell until the
level is up to the upper line on the battery case
(Fig. 2).
Important Do not overfill the battery because
electrolyte (sulfuric acid) can cause severe corrosion and
damage to the chassis.
5. Wait five to ten minutes after filling the battery cells.
Add electrolyte, if necessary, until the electrolyte level
is up to the upper line on the battery case (Fig. 2).
6. Install battery filler caps.
1
2
3
m-5004
Figure 2
1. Fillercaps
2. Upper line 3. Lower line
Charging the battery produces gasses that can
explode.
Never smoke near the battery and keep sparks
and flames away from battery.
Warning

14
Note: Make sure the vent caps are installed in battery.
7. Charge the battery for 1 hour at 10 amps or 2 hours at
5 amps.
8. When the battery is fully charged, unplug the charger
from the electrical outlet, then disconnect the charger
leads from the battery posts (Fig. 3).
4
1
23
m-4970
Figure 3
1. Positive Battery Post
2. Negative Battery Post 3. Red (+) Charger Lead 4. Black (–) Charger Lead
9. Install the battery in the tractor and connect the battery
cables. Refer to the Installing the Battery on page 32.
Note: Do not run the tractor with the battery disconnected,
electrical damage may occur.
Checking the Engine Oil
Important The tractor is shipped from the factory with
oil in the engine crankcase
Check the oil level and add only enough oil to raise the
level to the full mark on the dipstick. Refer to Checking
the Engine Oil on page 24.
Checking the Tractor
Lubrication
Check the tractor to ensure it is lubricated. Refer to
Greasing and Lubrication on page 27.
Learn to Operate the Tractor
Learn how to operate the tractor. Read the Operation
section starting on page 15.
Test Driving the Tractor
1. Fill the tank with unleaded regular gasoline; Gasoline
and Oil, page 12. Open the fuel shutoff valve and
check the fuel hose and fittings for leaks.
2. As applicable, check and test the operation of the
following:
•Engine, choke and throttle controls
•Headlights
•Indicator lights
•PTO clutch and brake
•Lift system
•Parking brake
•Steering
•Tractor operation in forward and reverse
Checking the Safety System
If safety interlock switches are disconnected or
damaged the machine could operate unexpectedly
causing personal injury.
•Do not tamper with the interlock switches.
•Check the operation of the interlock switches
daily and replace any damaged switches before
operating the machine.
Caution
Refer to Checking the Safety Interlock System on
page 17.

15
Operation
Think Safety First
Please carefully read all the safety instructions. Knowing
this information could help you, your family, pets or
bystanders avoid injury.
Controls for Model 72201
Become familiar with all the controls (Fig. 1) before you
start the engine and operate the machine.
2
3
4
8
9
10
11
1
6
5
7
12
m–6514
13
Figure 1
1. Steeringwheel
2. Ignition switch
3. Brake pedal
4. Parking brake lever
5. Ground speed selector
6. Throttle lever
7. Choke lever
8. Power take off (PTO)
9. Cruise control switch
10. Indicator control
module/Hourmeter
11. Tilt wheel lever
12. Hood opening
13. Attachment lift
Controls for Model 72202
Become familiar with all the controls (Fig. 2) before you
start the engine and operate the machine.
2
3
4
8
9
10
12
1
6
11
5
7
13
m–6513
Figure 2
1. Steeringwheel
2. Ignition switch
3. Brake pedal
4. Parking brake lever
5. Ground speed selector
6. Throttle lever
7. Choke lever
8. Power take off (PTO)
9. Cruise control switch
10. Indicator control
module/Hourmeter
11. Attachment lift switch
12. Tilt wheel lever
13. Hood opening
Operating the Parking Brake
Always set the parking brake when you stop the machine
or leave it unattended.
Setting the Parking Brake
1. Push the brake pedal (Fig. 3) down and hold it in the
depressed position.
2. Push the parking brake lever (Fig. 3) forward and
gradually take your foot off the brake pedal. The brake
pedal should stay in the depressed (locked) position.

16
Releasing the Parking Brake
1. Push down on the brake pedal (Fig. 3). The parking
brake lever should release.
2. Gradually release the brake pedal.
1
2
m–6516
Figure 3
1. Brake pedal 2. Parking brake lever
Starting and Stopping the
Engine
Starting the Engine
1. Sit down on the seat.
2. Set the parking brake; refer to Setting the Parking
Brake, page 15.
Note: The engine will not start unless you set the parking
brake or fully depress the brake pedal.
3. Push the PTO (power take off) to the off position
(Fig. 4).
4. Move the choke lever to the on position (Fig. 4).
Note: An engine that has been running and is warm may
not require step 4.
5. Move throttle lever to the fast position (Fig. 4).
6. Turn the ignition key and hold it in the start position
(Fig. 5). When the engine starts, release the key.
Important If the engine does not start after 10 seconds
of continuous cranking, turn the ignition key to off and let
the starter motor cool for 60 seconds; refer to
Troubleshooting, page 37.
7. After the engine starts, move the choke lever to off
(Fig. 4). If the engine stalls or hesitates, move the
choke lever back to on for a few seconds. Then move
the throttle lever to desired setting. Repeat this as
required.
5
3
1
2
6
m–6523
4
Figure 4
1. PTO—Off
2. Choke–On
3. Choke–Off
4. Throttlelever
5. Fast
6. Slow
3
2
1
1208
4
Figure 5
1. Off
2. Lights 3. Run 4. Start
Stopping the Engine
1. Push the PTO (power take off) to off (Fig. 4).
2. Move the throttle lever between half and full throttle
(Fig. 4).
3. Turn the ignition key to off (Fig. 5).

17
Operating the Power Take Off
(PTO)
The power take off (PTO) engages and disengages power
to the electric clutch.
While the ignition key is in run or lights position and the
power take off (PTO) is engaged on, the PTO light, in the
Indicator Module, will be on. When this light is on it is a
reminder; the starter will not crank and to turn the off PTO
before getting off.
Engaging the Power Take Off (PTO)
1. Pull the power take off (PTO) to on (Fig. 6).
12
m–6524
Figure 6
1. Off—disengaged 2. On—engaged
Disengaging the Power Take Off (PTO)
1. Push the power take off (PTO) to off (Fig. 6).
The Safety Interlock System
If safety interlock switches are disconnected or
damaged the machine could operate unexpectedly
causing personal injury.
•Do not tamper with the interlock switches.
•Check the operation of the interlock switches
daily and replace any damaged switches before
operating the machine.
Caution
Understanding the Safety Interlock
System
The safety interlock system is designed to prevent the
engine from starting unless:
•You are sitting on the seat.
•The brake pedal is depressed.
•The power take off (PTO) is off.
•The hydro control pedal is in the neutral position.
The safety interlock system is designed to stop the engine
if:
•You rise from the seat when the brake pedal is released
•You rise from the seat when the power take off (PTO)
is on.
The safety interlock system is designed to stop the power
take off (PTO) if:
•You shift into reverse with the power take off (PTO)
engaged.
Testing the Safety Interlock System
Test the safety interlock system before you use the
machine each time. If the safety system does not operate
as described below, have an Authorized Service Dealer
repair the safety system immediately.
1. Set the parking brake. Move the power take off (PTO)
to the On position. Now turn the ignition key to start
while sitting on the seat; the engine should not crank.
2. Push the power take off (PTO) to the off position and
release the parking brake. Now turn the ignition key to
the Start position while sitting on the seat; the engine
should not crank.
3. Set the parking brake and move the power take off
(PTO) to the Off position. Rise from the seat and turn
the ignition key to the Start position; the engine
should not crank.
4. Set the parking brake and move the power take off
(PTO) to the Off position. While sitting in the seat,
start the engine. While the engine is running, release
the parking brake and rise slightly from the seat; the
engine should stop.
5. et the parking brake and move the power take off
(PTO) to the Off position. While sitting in the seat,
start the engine. While the engine is running, move the
power take off (PTO) to the On position and rise
slightly from the seat; the engine should stop.
6. With the parking brake released, turn the ignition key
to the RUN run position without starting the engine.
Pull the PTO switch to on. You should hear an audible
click indicating the PTO is activated and the PTO light

18
will illuminate. Move the foot pedal to reverse. You
should hear an audible click indicating the PTO is
deactivated and the PTO light should turn off.
7. With the parking brake released, turn the ignition
switch to RUN without starting the engine. Pull the
PTO switch to on. Turn the KeyChoice key and
release. The Operating-in-Reverse warning light
should illuminate. Move the foot pedal to reverse. The
PTO and PTO light on the dash should remain on.
Push the PTO switch to off. The PTO light and the
Operating-in-Reverse warning light should turn off.
Setting the KeyChoiceSwitch to
Operate in Reverse
An interlock feature on the tractor prevents the power take
off (PTO) from operating when backing up. If you shift
into reverse with the PTO engaged (i.e., with mower
blades or other attachment running), the PTO will
disengage. Do not mow in reverse unless absolutely
necessary.
If you need to use the PTO while backing up, you can turn
off this interlock feature using the KeyChoice switch
located near the seat bracket (Fig. 7).
Danger
You could back over a child or bystander while
the mower blade(s) or other attachment is
engaged and cause serious injury or death.
•Do not mow in reverse unless absolutely
necessary.
•Do not insert the KeyChoice key unless it is
absolutely necessary.
•Always look backward and down before
backing up.
•Use the KeyChoice switch only if you are
certain no children or other bystanders will
enter the mowing area.
•Be very observant after deactivating the
interlock because the sound of the engine may
prevent you from noticing that a child or
bystander has entered the work area.
•Always remove both the ignition and
KeyChoice keys and put them in a safe place
out of the reach of children or unauthorized
users when leaving the unit unattended.
1. Engage the PTO.
2. Insert the KeyChoice key into the switch (Fig. 7).
m–4220
1
Figure 7
1. KeyChoiceswitch
3. Turn the KeyChoice key.
A red light on the front console (Fig. 8 and 9) turns on,
indicating that the interlock is disabled.
1
m–6517
Figure 8
1. Operating-in-reverselight—Model 72202
1
m–6518
Figure 9
1. Operating-in-reverselight—Model 72201
4. Shift into reverse and complete your task.
5. Stop the PTO, which will turn off the red light on the
console, to activate the interlock.
6. Remove the KeyChoice key and put it in a safe place
out of reach of children.

19
Indicator Control Module
The indicator control module (Fig. 10) contains lights for:
•Operating in reverse
•Power take off (PTO)
•Battery
•Oil pressure
•Hourmeter (LED)
•Cruise control (Model 72202 only)
•Fuel level (Model 72202 only)
7531 42 6
m–6517
Figure 10 (Model 72202)
1. Power take off (PTO)
2. Cruise control
3. Battery
4. Hourmeter
5. Fuel level
6. Oil Pressure
7. Operating-in-Reverse
1
4
25 3
m–6518
Figure 11 (Model 72201)
1. Power take off (PTO)
2. Battery
3. Hourmeter
4. Oil pressure
5. Operating-in-Reverse
Following are the conditions when indicator lights will be
on. At other times the lights should be off.
Operating in Reverse
The Operating–in–Reverse light will illuminate whenever
the KeyChoice switch is used to deactivate the
operating-in-reverse interlock. It is a reminder that the
interlock system is deactivated. The light goes out
whenever the power take off (PTO) is disengaged or the
engine is shut off.
PTO (Power Take Off)
The PTO (power take off) light will be on when the
ignition key is in the run or lights positions and the PTO
(power take off) is engaged on. When this light is on it is
a reminder; the starter will not crank and turn off the PTO
before getting off.
Hourmeter
The hourmeter records the number of hours the engine has
operated (Fig. 10). It is turned on when the ignition switch
is in the run or lights positions. Use the times for
scheduling regular maintenance.
Battery
The battery light will be on when the ignition key is in the
run or lights positions if the battery voltage is below
11.2 volts. When this light comes on it is important to
have your battery and electrical system checked and the
problem corrected.
Fuel Level
The fuel level light will be on when the ignition key is in
the run or lights positions and the fuel level is low,
approximately one pint remaining.
Oil
The oil light will be on when the ignition key is in the run
or lights positions and the engine is not running, after the
engine is started the light should go out. When the engine
is running if the oil pressure drops below a safe operating
level the light comes on. When the light comes on while
the engine is running, Stop engine immediately and
correct the cause of low oil pressure.
Driving Forward or Backward
The throttle control regulates the engine speed as
measured in rpm (revolutions per minute). Place the
throttle control in the fast position for best performance.
To go forward or backward, release the parking brake:
refer to Releasing the Parking Brake, page 16. Place your
foot on the traction control pedal and slowly press on the
top of the traction control pedal to move forward or on the
bottom of the traction control pedal to move backward
(Fig. 12). The farther you move the traction control pedal
in either direction, the faster the machine will move in
that direction.
Note: For reverse motion, with the PTO engaged, the
operating-in-reverse interlock must be deactivated by the
KeyChoice switch located on the seat bracket on the right
hand side just below the seat.

20
To slow down, release the pressure on the traction control
pedal.
Important To avoid transmission damage, always
release the parking brake before moving the traction
control pedal.
1
2
1210
Figure 12
1. Forward 2. Backward
Stopping the Machine
To stop the machine, release the traction control pedal,
disengage the power take off (PTO), and turn the ignition
key to off. Also set the parking brake if you leave the
machine unattended; refer to Setting the Parking Brake,
page 15. Remember to remove the key from the ignition
switch.
Children or bystanders may be injured if they
move or attempt to operate the tractor while it is
unattended.
Always remove the ignition and KeyChoice keys
and set the parking brake when leaving the
machine unattended, even if just for a few
minutes.
Caution
Using the Attachment Power
Lift
The attachment power lift (Fig. 13) is used to raise and
lower attachments.
Raising Attachments
1. Turn key to the on or run position (Fig. 13).
2. Push the lift switch in the up direction to raise the
attachment lift (Fig. 13). This will lift and hold the
attachment in the up, or raised position.
Lowering Attachments
1. Turn key to the on or run position (Fig. 13).
2. Push the lift switch in the down direction to lower the
attachment lift (Fig. 13). This will lower the
attachment lift.
m–6513
2
31
Figure 13
1. Key
2. Lift switch —up 3. Lift switch —down
Operating the Attachment Lift
Lever
The attachment lift lever (Fig. 14) is used to raise and
lower various attachments.
Raising an Attachment
1. Depress the clutch and brake pedals to stop the
machine.
2. Pull attachment lift lever rearward until latch locks. In
this position the lift will hold the attachment in the up,
or raised position.
Lowering an Attachment
1. Depress the clutch and brake pedals to stop the
machine.
2. Pull attachment lift lever rearward, to release lift
pressure, and push the button on top to release the
latch. Move lift lever forward to lower attachment.