Tree Frogs Super 360 Spiral Slide User manual

© 2019 KID STRUCTURES INC.
4465 West Sam Houston Parkway N.
Houston, Texas 77041
WWW.TREEFROGSSHOWROOMS.COM
Sections
Page 1: Part List
Page 2: 5.8’ Deck Height Assembly
Page 3: 5’ & 7’ Deck Height Assembly
Page 4: 6.5’ Deck Height Assembly
Version 1:19
Super 360 Spiral Slide
Installation Manual

3/8” x 5”
Lag Screw
QTY. 2
5/16” x 1 1/2”
Lag Screw
QTY. 26
5/16” x 1”
Hex Bolt
QTY. 99
5/16”-18
Lock Nut
QTY. 97
5/16”
Flatwasher
QTY. 222
3/8”
Flatwasher
QTY. 2
Entry Panel
10 Degree Section
30 Degree Section
90 Degree Section
90 Degree Section
90 Degree Section
Exit Chute
PARTS

1) Turn 10° 1 Bolt Hole CCW
2) Turn 30° 1 Bolt Hole CCW
3) Turn 90° Elbow 0 Bolt Hole to
even seam
4) Turn 90° Elbow 2 Bolt Holes CW
5) Turn 90° Elbow 2 Bolt
Holes CW
6) Aach Exit Chute Level To
Ground
Quick Reference Guide #1
For 5.8’ Deck Height
NOTE: To spiral in the opposite direction, apply CW turns instead of CCW and
vice versa. Turns may need to be adjusted depending on the level of the land.

Quick Reference Guide #2
For 5’ & 7’ Deck Heights
NOTE: To spiral in the opposite direction, apply CW turns instead of CCW and
vice versa. Turns may need to be adjusted depending on the level of the land.
1) Turn 10° 1 Bolt Hole CW
2) Turn 30° 0 Bolt Hole With Even
Seem
3) Turn 90° 1 Bolt Hole CW
4) Turn 90° Elbow 2 Bolt Holes CCW
5) Turn 90° Elbow 2
Bolt Holes CW
6) Aach Exit Chute Level To
Ground

Quick Reference Guide #3
For 6.5’ Deck Height
1) Turn 10° 1 Bolt Hole CCW
2) Turn 30° 2 Bolt Hole CW
3) Turn 90° Elbow 1 Bolt
Hole CW
4) Turn 90° Elbow 2
Bolt Holes CCW
5) Turn 90° Elbow 2 Bolt Holes
CCW
6) Aach Exit
Chute Level To
Ground
NOTE: To spiral in the opposite direction, apply CW turns instead of CCW and
vice versa. Turns may need to be adjusted depending on the level of the land.

Step #1
Assemble the Elbow Section Halves together with the hardware as shown.
Note the position of the Overlap Flanges in relation to the direction of the
Bolts.
90 Section RH Lock Nut Washer
Overlap
Flanges
90 Section LH Bolt Washer

Step #2
Using Nuts, Washers and Bolts, attach the 10 Elbow
to Entry Panel in the "Quick Reference" orientation.
Step #3
After properly blocking the slide entrance on the
playset, attach the Entry Chute/first Elbow assembly to
the playset with the Lag Screws and Washers provided.
Bolt Washer
Washer
Lock Nut
Step #4
Using Nuts, Washers and Bolts,
attach the 30 Elbow to the
previous Elbow in the "Quick
Reference" orientation.

Step #5
Using Nuts, Washers and
Bolts, attach the 90 Elbow to
the previous Elbow in the
"Quick Reference" orientation.
Step #6
Using Nuts, Washers and Bolts, attach
the 2nd 90 Elbow to the previous
Elbow in the "Quick Reference"
orientation.
Step #7
Using Nuts, Washers and Bolts, attach
the 3rd 90 Elbow to the previous
Elbow in the "Quick Reference"
orientation.

Step #8
Place the end of the Exit Chute up against the last Elbow Section and make it level with
the ground. If any of the last Elbow bolt holes line up with the Exit Chute attach with
Bolts and Washers (possibly 2 Places). For all the holes that don't line up attach with Lag
Screws and Washers. (as many as 12 places) Start each Bolt by hand before tightening.
Be careful not to overtighten the Lag Screws into the soft plastic.
Lag Screws
& Washers
Hex Bolts & Washers
(if possible)
Rest on ground