TREND SDU-Lon User manual

SDU-LonInstallationInstructionsTG200599Issue1/C20/11/06 1
Installation Instructions
SDU-Lon
Smart Display Unit
Important:Retaintheseinstructions
3 Installation
1 Unpacking
SDU-LON Installation
InstructionsTG200599
H O
2
-10 °C
+14 °F +50 °C
+122 °F 0 %RH 95 %RH
2 Storing
Itisrecommended thattheinstallationshould
complywiththeHSEMemorandumofGuidance
on Electricity at Work Regulations 1989.
ForUSAinstallequipmentinaccordancewith
the National Electric Code.
WARNING: Other than removing
frontpanel(step3),donotopenunit.
DANGER high voltage. No
serviceable parts inside.
Note that this product may involve Lonworks system integration as referred to in step 12:
this procedure should only be performed by an installer with LonWorks engineering
expertise.
!
Dimensions
190 mm (3.54”)
25 mm
(0.98”)
30 mm (1.18”)
90 mm (3.54”)
150 mm (6”) 150 mm (6”)

SDU-Lon InstallationInstructions
SDU-LonInstallationInstructionsTG200599Issue1/C20/11/06
2
3 Installation(Continued)
Requirements (continued)
2
bc
H O
2
-10 °C
+14 °F +40 °C
+104 °F
0 %RH 90 %RH
a
Remove Front Panel
3
Route Cables
5
b
a
c
Check SDU type
4
Check SDU-LON
*Ifonesideofthe24Vacinputpowerisconnected
to 0 V, that side must be connected to the SDU
-(negative)terminal
+
+
+24 Vdc
24 Vdc Power
Supply
SDU
0 Vdc
+
+24 Vac (L)
24 Vac Power
Supply
SDU
+24 Vac (N)
24 Vdc
15 mA
24 Vac
15 mA
*
O
I
S P E N G
1 2 3 4
SDU
Configure SDU
6to change operating mode, restrictive set, or language
a Connect Input Power b Switch on Power
24 V
Power
Supply

SDU-LonInstallationInstructionsTG200599Issue1/C20/11/06 3
InstallationInstructions SDU-Lon
+
24 V
Power
Supply
LCI
RJ11
SDU-LON
supplied with LCI
Cable/EJ101442
9 way D type Female
LonWorks
LonWorks
SET,
SDU Tool
3 Installation(Continued)
Configure SDU (Continued)
6
LCI Installation Instructions
TG200429
c Connect to PC
d Set up SDU Configuration File
SDU Tool Set up:
Mode Unrestricted/Restricted
Home Page Show/Don’t show
Restrictive mode list Select required modules
Language Translation of standard text
Backup File to Disk
S P E N G
1 2 3 4
SDU Data Sheet TA200559
SDUToolManualTE200600
SET
SDU Tool Select
Language
Download to
SDU
f Download Language
DownloadComplete
h Set SDU into Download Mode
S P E N G
1 2 3 4
Config Update
i Transfer Completed
S P E N G
1 2 3 4
Config Update
j Switch off Input Power
SP ENG
1234
O
I
24 V
SDU
e Identify SDU to SDU Tool
g Download Completed
SP - service pin

SDU-Lon InstallationInstructions
SDU-LonInstallationInstructionsTG200599Issue1/C20/11/06
4
I Q L I Q L S D U S D U
L O N
R o u t e r
L O N
R o u t e r
Lon Lon
segm ent
a s s o c i a t e d
a s s o c i a t e d
V i r t u a l
Lan
3 Installation(Continued)
Note that: If two SDU/LONs are associated with IQLs which are on the same Lan, the SDU-LONs
must be on the same segment (i.e. on the same section of LonWorks separated by routers).
If the system is installed on a LonWorks Management Tool (as in step 12), this rule does
not apply.
I Q L I Q L S D U S D U
L O N
R o u t e r
L O N
R o u t e r
Lon Lon
segm ent
a s s o c i a t e d a s s o c i a t e d
V i r t u a l
Lan
Connect to LonWorks
7
+
Lon
Lon
T e r m i n a t o r
T e r m i n a t o r
T e r m i n a t o r
Star topology Ring
topology
Bus topology
1 0 0
m
, 5 0 V m i n
1 0 0
m
, 5 0 V m i n
Do not allow wires
to cross on a loop
* Terminate bus at one end only
Terminator
e.g.LONTERMINATOR
Terminal size 0.5 to 2.55 mm2 (14 to 20 AWG)
Normal Trend Lan cable is not recommended.
Do not use screened cable.
elbaChtgnelsubxaM otedonxaM edon
20158nedleB)sdy545(m005)sdy545(m005
metsysQI 002/FH/61/0/1/PT )1748nedleB( )sd
y545(m005)sdy034(m004
GWA22,VIleveLLU)sdy545(m005)sdy034(m004
8.0x2x2Y)tS(YJ)sdy545(m005)sdy053(m023
GWA42,5.
taCA865AIT)sdy094(m054)sdy072(m052
LonA
SCN
LonB LonA
SCN
LonB
LINC
A
IQLROUTER
B
IQL
xy
A
IQLROUTER
B
z
w
LONC
IQL
xyz w
LonA
SCN
LonB LonA
SCN
LonB
LONC
LonA
SCN
LonB LonA
SCN
LonB
456789
1011
T
T
T
456789
1011
SDU
xcite
Maximum 64 nodes per Lon segment
Maximum 40 IQLs (and LONCs) per Lan
Recommend terminate at
LINC or Router.
e.g. use IQLRouter integral
terminators

SDU-LonInstallationInstructionsTG200599Issue1/C20/11/06 5
InstallationInstructions SDU-Lon
*Ifoneside of the24 Vac input poweris connected to0 V, that sidemust be connectedtothe SDU -(negative)
terminal
Connect Input Power
8
Check Start Up Reset
10
S P E N G
1 2 3 4
T r e n d S D U V 1 . 0
Firmware version communications failure
or no sensor set up
Connect to IQ
Check LonWorks Connected
11
+
LonWorks (green)
SDU faulty
Switch on Input Power
9
failed to install on Lon;
check step 7
installed on Lon
3 Installation(Continued)
+
+
+24 Vdc
24 Vdc Power
Supply
SDU
0 Vdc
+
+24 Vac (L)
24 Vac Power
Supply
SDU
+24 Vac (N)
24 Vdc
15 mA
24 Vac
15 mA
*
O
I
S P E N G
1 2 3 4
SDU
24 V Power
Supply

SDU-Lon InstallationInstructions
SDU-LonInstallationInstructionsTG200599Issue1/C20/11/06
6
Mount Unit
14
Standard UK pattress wall box
or panel 60 mm
46 mm
50 mm
Ø 4 mm
(M3.5
screw)
Ø 4 mm
(M3.5
screw)
60 mm
2 off (M3.5 x 35 mm)
screws provided
Install on Lon Management Tool
12 If other IQ System devices on LonWorks are installed on LonWorks Management Tool.
WheninstallingSDU-LONonLonWorkManagementTool,pushservicepinbuttonwhenrequested.
S P E N G
1 2 3 4
See LonWorks network management tool
manual. See IQ System LonWorks Products
Engineering Manual (TE200292). LonWorks
System integrator must have LonWorks
engineeringexpertise.
SDUDataSheetTA200559
for LonWorks network
variables (NVs)
The SDU must also be associated with its IQL using the LMT
The following network variables need to be set up using the LMT:
nciInstallState: set to CFG_EXTERNAL
nciHostNodeAddr: set to associated IQL LonWorks node address
nciSubnetAddr: set to associated IQL LonWorks subnet address
nciMsgCode: set message code of associated IQL
nciDomainIndex: set to domain index of associated IQL
service pin button
Associate SDU with its IQL
13
ab
not if installed on LonWorks Management Tool
SP ENG
1234
Conn ect to IQ
“Connect to IQ”
SP ENG
1234
Press IQL Ser vic e PIN
“Press IQL
Service Pin”
cd
4 secs
EitheruseIQLTool2runinginSETandconnectedtoLonWorksusingLCIorusebuttonsasfollows:
3 Installation(Continued)
24Vac
I Q L
 
+
O / S
L A N
L O N
N I D
S t r a t e g y
: : : : :
D O 1 I N 1
D O 2 D O 3
~
D O 4 D O 5 IN 2 I N 3
2 4 V
C O M
24V
C O M
~
C O M
service pin button

SDU-LonInstallationInstructionsTG200599Issue1/C20/11/06 7
InstallationInstructions SDU-Lon
3 Installation(Continued)
Check Display
16
1234
S e n s r 1
F l r 1 S p a c e T e m p
2 0 . 3 D e g C
Displays first labelled
sensor if set to
defaults
Replace Front Panel
15
Check Operation - Monitor
17
1234
Sensor
S e n s r 1
F l r 1 S p a c e T e m p
2 0 . 3 D e g C
Knob
Switch
Driver
Digital Input
Time Zone
Time
1234
S e n s r 1
F l r 1 S p a c e T e m p
2 0 . 3 D e g C
Sensor 1
Sensor 2
Sensor (last)
1234
Calendars Notethatthefullsequencelistedhere
may only be shown in Unrestricted
modes. The Restricted modes show
only those pages on the Restricted
list. The Home page is optional (see
step 6d).
Plant Room 1
20/03/02 08:04
Home page

SDU-Lon InstallationInstructions
SDU-LonInstallationInstructionsTG200599Issue1/C20/11/06
8
3 Installation(Continued)
1234 1234
Check Operation - Adjust
18
1234
Digital
ON
Analogue
if PIN required
see step 19
OFF
Units 20.32
Tenths 20.32
Knob 1
Room 1 Setpoint
20.01 DegC
Knob 1
Room 1 Setpoint
20.01 DegC
Knob 1
Room 1 Setpoint
20.01 DegC
Hundreths 20.32

SDU-LonInstallationInstructionsTG200599Issue1/C20/11/06 9
InstallationInstructions SDU-Lon
1234
S e n s r 1
F l r 1 S p a c e T e m p
2 0 . 3 D e g C
Enter PIN
19
aPIN 5 * * *
b
cPIN X 5 * *
d
ePIN X X 5 *
f
gPIN X X X 5
h
1234
P I N 5 * * * *
If required
3 Installation(Continued)

SDU-Lon InstallationInstructions
SDU-LonInstallationInstructionsTG200599Issue1/C20/11/06
10
Set SDU Mode
20 If required
S P E N G
1 2 3 4
S e n s r 1
F l r 1 S p a c e T e m p
2 0 . 3 D e g C
Display Mode = 1
S e n s r 1
F l r 1 S p a c e T e m p
2 0 . 3 D e g C
Display Mode = 7
Default - Display Mode 0:
No home page, alarm log disabled
Notethat ifthe home pageis enabled,the controller’s identifier[R(D)] shouldbeset up,otherwise
the first line of the home page will show the label of the previous item displayed.
3 Installation(Continued)
aRemove front panel - see step 3
bSet mode
cReplace front panel - see step 15
edoMteSegaP emoH
egaP
mralA
goL
0detcirtsernUoNoN
1detcirtsernUseY oN
2detcirtsernUoNoN
3detcirtsernUseY oN
4detcirtseRoNoN
5detcirtseRseY oN
6detcirtseRoNoN
7detcirtseRseY oN
Notethatthealarmlogispermanentlydisabled
forSDU-LONsotheSDUmodeselectsrestricted/
unrestrictedand homepage
Engineering Resets
21
If need temporary Unrestricted mode for commissioning or need Manual reset (e.g. after multiple
mode changes as in step 20)
1234
Hold 5 secs - 10 secs Temporary Unrestricted Mode - returns to
previous mode 20 seconds after last key press.
Hold 10 secs or greater Manual Reset

SDU-LonInstallationInstructionsTG200599Issue1/C20/11/06 11
InstallationInstructions SDU-Lon
Set up Parameters
22
Set up the following parameters for IQL using SDU:
Knobs
Switches
Time Zone Day of week (1 to 14) Period (1 to 3)
Start hours, minutes Stop hours, minutes
Time hrs, minutes, day of month, month, year
daylight saving on, day of month, month
daylight saving off, day of month, month
Calendars Use (next, Free, every)
Start date Stop date
Special day type for the zone
SDU Data Sheet
TA200559
If required
Notethat ifa 963is tocentrally control theIQL’s occupationstate, thenthe SDUtimezone’s times
should be left nulled at 00:00.
Note that if a 963 is centrally synchronising time, it should do so using a timemaster which will in
turn synchronise the SDU.
3 Installation(Continued)

SDU-Lon InstallationInstructions
SDU-LonInstallationInstructionsTG200599Issue1/C dd/mm/yy
12
ManufacturedforandonbehalfoftheEnvironmentalandCombustionControlsDivisionofHoneywellTechnologiesSàrl,Ecublens,Route
duBois37,SwitzerlandbyitsAuthorizedRepresentative,TrendControlSystemsLimited.
TrendControlSystemsLimitedreservestherighttorevisethispublicationfromtimetotimeandmakechangestothecontenthereof
withoutobligationtonotifyanypersonofsuchrevisionsorchanges.
Trend Control Systems Limited
P.O.Box34,Horsham,WestSussex,RH122YF,UK.Tel:[phone]Fax:[phone]www.trend-controls.com
Trend Control Systems USA
6670185thAvenueNE,Redmond, Washington 98052, USA. Tel: [phone], Fax: [phone] www.trend-controls.com
WEEEDirective :
Attheendoftheirusefullifethepackaging,
andproduct,shouldbedisposedofbya
suitablerecyclingcentre.
Donotdisposeofwithnormalhouseholdwaste.
Donotburn.
4 Disposal