Trieste TR602IX Installation and operating instructions

Dear Customer,
Thank you for having purchased one of our products.
We are certain that this new, modern, functional and practical appliance, built with the very highest
quality materials, will meet your requirements in the best possible way. This appliance is easy to
use. It is, however, important to thoroughly read the instructions in this handbook in order to obtain
the best results.
These instructions are only valid for the countries of destination, the identification symbols of
which are indicated on the cover of the instruction manual and on the appliance itself.
The manufacturer shall not be held responsible for any damages to persons or property caused
by incorrect installation or use of the appliance.
The Manufacturer shall not be held responsible for any inaccuracies in this handbook due to printing or
transcription errors; the designs in the figures are purely indicative. The Manufacturer also reserves the right
to make any modifications to the products as may be considered necessary or useful, also in the interests
of the user, without jeopardizing the main functional and safety features of the products themselves.
COD. 01029EUR - 08.03.2010
IN TRUCTION AND ADVICE FOR THE
U E, IN TALLATION AND MAINTENANCE
OF BUILT-IN ELECTRIC HOB
MODEL: TR602IX - TR602WH

2
4 Ø 145 mm rapid electric plate of 1500 W
5 Ø 180 mm rapid electric plate of 2000 W
11 Electric plate n° 5 control knob
12 Electric plate n° 4 control knob
13 Electric plate ignition warning light
Attention: this appliance has been manufactured for domestic use only and it employment by
private person.
DE CRIPTION OF THE HOT PLATE

3
U E
1) HOW TO U E THE ELECTRIC HOT
PLATE
Mixed hot plates may be equipped with a normal or
rapid plates. These are controlled by switches with
various positions (see fig. 1 and are switched on
by turning the knob to the required setting. A
diagram is screen-printed above each knob on the
front panel. This diagram indicates to which
electric plate the knob in question corresponds
(see fig. 1). A red warning light will come on to
indicate that the plate is operating.
A purely indicative regulation table for the electric
plates is given below.
NORMAL OR
RAPID PLATE
HEAT
INTEN ITY
PO IBLE COOKING
PROCE E
TABLE
0
1
2
3
4
5
6
Off
Weak
Low
Slow
Medium
Strong
High
To dissolve butter, chocolate, etc.. To heat small
amounts of liquid.
To heat larger amounts of liquid. To prepare cremes
and suces requiring long slow cooking times.
To thaw frozen foods and prepare stews, heat to boiling
point or simmer.
To heat foods to boiling point. To brown delicate meats
and fish.
For escalopes and steaks. To simmer large amounts of
food.
To bring large amounts of liquid to the boil. For frying.
FIG. 1

4
U E
WARNINGS:
when the plate is switched on for the first time, or if it has remained unused for a long period, it should
be dried for 30 minutes on switch position n° 1. This will eliminate any moisture that may have been
absorbed by the insulating material.
To correctly use the appliance, remember:
- to place a pan on the plate before switching this on.
- To always use pans with flat and very thick bottoms (see fig. 2).
- To never use pans that are smaller than the plate diameters.
- To dry the bottom of the pan before placing it on the plate.
- Never leave the appliance unattended when the plates are being used. ake sure that there are no
children in the near vicinity. Particularly make sure that the pan handles are correctly positioned and
keep a check on foods requiring oil and grease to cook since these products can easily catch fire.
- The plates will remain hot for a long period of time even use after use, never touch them with the
hands or other objects in order to prevent burns.
- Immediately disconnect the appliance from the electricity main as soon as cracks are noted on the
surfaces of the plates.
- If the built-in hot plate has a lid, any spilt food should be immediately removed from this before it is
opened. If the appliance has a glass lid, this could shatter when the cooker becomes hot. Always
switch off all the plates before closing the lid.
FIG. 2

5
CLEANING
I PORTANT:
always disconnect the appliance from the
electricity main before carrying out any cleaning
operation.
2) HOT PLATE
If you want to preserve the surface clean and
bright, periodically wash the hot plate with
lukewarm soapy water.
Following this, all parts should be thoroughly rinsed
and dried. ever wash them while they are still
warm and never use abrasive powders.
Do not allow vinegar, coffee, milk, salted water,
lemon or tomato juice from remaining in contact
with the enamelled surfaces for long periods of
time.
WARNINGS:
- correctly preserve the plate after use by
treating it with special products, easily
available on the market. This will keep the
surface of the plate clean and bright. The
operation will also prevent the formation of
rust.
- Any liquid overflowed the pans, must be
always remove with a rag.
- Don’t use steam jets for the equipment
cleaning.

IN TALLATION
TECHNICAL INFOR ATION FOR
THE INSTALLER
Installation and maintenance must only be
carried out by a qualified installer.
Incorrect installation could cause damage to
persons, animals and property for which the
manufacturer cannot be held responsible.
3) IN TALLING THE HOT PLATE
Check that the appliance is in a good condition
after having removed the outer packaging and
internal wrappings from around the various loose
parts. In case of doubt, do not use the appliance
and contact qualified personnel.
Never leave the packaging materials
(cardboard, bags, polystyrene foam, nails, etc.)
within children's reach since they could
become potential sources of danger.
The measurements of the opening made in the top
of the modular cabinet and into which the hot plate
will be installed are indicated in either fig. 3, comply
with the measurements given for the hole into which
the appliance will be recessed (see fig. 4).
If a wood is installed above the hob, please look at
the hood manufacturer instructions regarding the
minimum distance between hood and hob (fig. 4).
4) FIXING THE HOT PLATE
The hob has a special seal which prevents liquids
from infiltrating into the cabinet. Strictly comply
with the following instructions in order to correctly
apply this seal:
- detach the seals from their backing, checking
that the transparent protection still adheres to the
seal itself.
- Overturn the hob and correctly position seal “E”
(fig. 5) under the edge of the hob itself, so that
the outer part of the seal itself perfectly matches
the outer perimetral edge of the hob. The ends of
the strips must fit together without overlapping.
- Evenly and securely fix the seal to the hob,
pressing it in place with the fingers and remove
the strip of protective paper from the seal and set
the plate into the hole made in the cabinet.
- Fix the hotplate to the worktop with the brackets
“S”. Ensure the tag fits into the hole “H” on the
hotplate base, then tighten the screw “F” until it is
locked to the worktop (fig. 6).
- In order to avoid accidental contact with the
surface of the box of the overheated hob during
use, it is necessary to install a wooden divider at a
minimum distance of 60 mm from the top,
fastening it in place with screws (fig. 3).
WARNINGS:
be aware that the glue that join the laminated
plastic to the furniture, has to resist to
temperature not below 150 °C, to avoid the
unstuck of the panelling.
The rear wall, adjacent and surrounding
surfaces must therefore be able to withstand
an overtemperature of 65 K.
FIG. 3
FIG. 4 FIG. 5 FIG. 6
CO PLY WITH THE
DI ENSIONS
(mm)
A B C D E
2E 282 482 59 59 100 min.
6

7
IN TALLATION
5) ELECTRICAL CONNECTION
The electrical connections of the appliance must
be carried out in compliance with the provisions
and standards in force.
Before connecting the appliance, check that:
- the electrical capacity of the mains supply and
current sockets suit the maximum power rating of
the appliance (consult the data label applied to the
underside of the hot plate).
- The socket or system has an efficient earth
connection in compliance with the provisions and
standards in force. The manufacturer declines all
responsibility for failing to comply with these
provisions.
When the appliance is connected to the
electricity main by a socket:
- fit a standard plug suited to the load indicated on
the data label to the cable.
- Fit the wires following figure 7, taking care of
respecting the following correspondences:
Letter L (live) = brown wire;
Letter N (neutral) = blue wire;
Earth symbol = green - yellow wire.
- The power supply cable must be positioned so that
no part of it is able to reach an overtemperature of
75 K.
- ever use reductions, adapters of shunts for
connection since these could create false contacts
and lead to dangerous overheating.
- The outlet must be accessible after the built-in.
When the appliance is connected straight to the
electricity main:
- install an omnipolar circuit-breaker between the
appliance and the electricity main. This circuit-
breaker should be sized according to the load
rating of the appliance and possess a minimum 3
mm gap between its contacts.
- Remember that the earth wire must not be
interrupted by the circuit-breaker.
- Alternatively, the electrical connection may also be
protected by a high sensitivity differential circuit-
breaker.
You are strongly advised to fix the relative yellow-
green earth wire to an efficient earthing system.
WARNINGS:
all our appliances are designed and
manufactured in compliance with European
standards EN 60 335-1 and EN 60 335-2-6 plus
the relative amendments.
The appliance complies with the provisions of
the following EEC Directives:
- CEE 2004/108/CE regarding to electromagnetic
compatibility.
- CEE 2006/95 regarding electrical safety.
FIG. 7

8
ERVICING
TYPE DIAMETER POWER RATING (W)
POWER RATING OF THE ELECTRICAL COMPONENT
Rapid plate with 7 positions with the protector 180 2000
Rapid plate with 7 positions with the protector 145 1500
Always disconnect the appliance from the
electricity main before proceeding with any
servicing operation.
6) REPLACING THE ELECTRICAL
COMPONENT
For access to the various parts, remove the hotplate
from the top of the cabinet. Then overturn it, unscrew
screw and remove under part.
After these actions is possible to work on the plates,
commutators, clamps and input cable.
N.B. In case of substitution of the input cable,
the installer must keep the “earth” conductor
longer than “live” ones, and must respect the
cautions in paragraph “Electrical connection”.
To reassemble the appliance repeat the inverse
process.
7) TECHNICAL CHARACTERI TIC OF
THE ELECTRICAL COMPONENT
To facilitate the job of the installer we present a scheme
with the characteristics of the components.
TYPE AND ECTION OF THE POWER CABLE
Cable type ingle phase power
230 - 240 V~
Rubber H05 RR-F
Polycroropene H05 R -F
3 X 1.5 mm2
3 X 1.5 mm2

9
TECHNICAL DATA
VOLTAGE 230 - 240 V~
FREQUE CY 50/60 Hz
TOT. RATI G 3500 W
MODEL WITH 2 RAPID PLATE

10
Before leaving the factory, this appliance will have been tested and regulated by expert and specialized
personnel in order to guarantee the best performances.
Any repairs or adjustments which may be subsequently required may only be carried out by qualified
personnel with the utmost care and attention.
For this reason, always contact your Dealer or our nearest After Sales Service Center whenever repairs or
adjustments are required, specifying the type of fault and the model of the appliance in your possession.
Please also note that genuine spare parts are only available from our After Sales Service Centers and
authorized retail outlets.
The above data are printed on the data label put on the inferior part of the appliance and on the packing
label.
The above informations give to the technical assistant the possibility to get fit spare parts and a heaven-
sent intervention. We suggest to fill the table below.
ARK: ........................................................................
ODEL: ......................................................................
SERIES: ......................................................................
TECHNICAL A I TANCE AND PARE PART
This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and
Electronic Equipment (WEEE).
This guideline is the frame of a European-wide validity of return and recycling on Waste Electrical and
Electronic Equipment.

11

12