Wolf RT486GLP User manual

INSTALLATION INSTRUCTIONS
GAS RANGETOPS

As you follow these instructions, you will
notice WARNING and CAUTION symbols.
This blocked information is important for the
safe and efficient installation of Wolf equip-
ment. There are two types of potential
hazards that may occur during installation.
Another footnote we would like to identify is
IMPORTANT NOTE: This highlights informa-
tion that is especially relevant to a problem-
free installation.
signals a situation where minor injury or
product damage may occur if you do not
follow instructions.
states a hazard that may cause serious
injury or death if precautions are not
followed.
WOLF®is a registered trademark of Wolf Appliance Company, LLC

Record the model and serial numbers before
installing the gas rangetop. Both numbers are
listed on the product rating plate. The rating
plate is located under the drip pan that
supports the cooking grates, on the left inside
wall of the rangetop. Refer to the illustration
below. The rating plate for French Top models
(except Model RT484F) is located on the right
inside wall.
Model Number
Serial Number
3
INSTALLATION REQUIREMENTS
IMPORTANT NOTE: This installation must
be completed by a qualified installer,
service agency or gas supplier.
IMPORTANT NOTE:
Save these Installation
Instructions for the local inspector’s use.
Please read the entire Installation Instruc-
tions prior to installation.
Installer: please retain these instructions
for local inspector’s reference, then leave
them with the homeowner.
Homeowner: please read and keep these
instructions for future reference and be sure
to read the entire Use & Care Information
prior to use.
IMPORTANT NOTE: This appliance must be
installed in accordance with National Electrical
Codes, as well as all state, municipal and local
codes. The correct voltage, frequency and
amperage must be supplied to the appliance
from a dedicated, grounded circuit which is
protected by a properly sized circuit breaker or
time delay fuse. The proper voltage, frequency,
and amperage ratings are listed on the product
rating plate.
WOLF GAS RANGETOPS
CONTACT
INFORMATION
Wolf Customer
Service:
800-332-9513
Website:
wolfappliance.com
Rating plate location
Location of rating
plate inside rangetop

4
BEFORE YOU START
Proper installation is your responsibility.
Installations must be performed by a
qualified or licensed contractor, plumber or
gas fitter, qualified or licensed by the state,
province or region where this appliance is
being installed. You must also assure that
electrical installation is adequate and
conforms with local codes and ordinances.
Wolf gas rangetops are manufactured for
use with
natural gas or LP gas .Please
check the product rating plate for type of
gas needed.
Proper gas connection must be available;
refer to Gas Supply Requirements on pages
10–12. Electrical ground is required; see
Electrical Requirements on page 13.
Check the location where the rangetop will
be installed. The location should be away
from strong draft areas, such as windows,
doors and strong heating vents or fans. Do
not obstruct the flow of air. The area in
which you are installing this appliance must
have an adequate supply of fresh air to
ensureproper combustion and ventilation.
Make sureyou have everything necessary
for correct installation. It is the responsibil-
ity of the installer to comply with the speci-
fied installation clearances. Refer to the
Installation Specifications illustrations for
your model on pages 8–9.
COMMONWEALTH OF MASSACHUSETTS
Installations and repairs must be performed
by a qualified or licensed contractor,
plumber or gasfitter qualified or licensed by
the state, province, or region where this
appliance is being installed.
Only use gas shut-off valves approved for
use within the state, province, or region
where this appliance is being installed.
Aflexible gas connector, when used, must
not exceed 3' (.9 m).
WOLF GAS RANGETOPS
IMPORTANT NOTE:
Installation and service must be
performed by a qualified installer,
service agency or the gas supplier.
Warranty service must be performed
by a Wolf authorized service center.
Do not storeor use gasoline or
other flammable vapors and liquids
in the vicinity of this or any other
appliance.
Aventilation hood is recommended
for use with the Wolf gas rangetop.
WHAT TO DO IF YOU SMELL GAS:
Do not tryto light any appliance.
Do not touch any electrical switch.
Do not use any phone in your
building.
Immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions.
If you cannot reach your gas
supplier, call the fire department.
If the information in this book is
not followed exactly, a fire or
explosion may result, causing
property damage, personal injury
or death.

5
Dimensions in parentheses are in
millimeters unless otherwise specified.
INSTALLATION INSTRUCTIONS
VENTILATION CONSIDERATIONS
The front of your Wolf gas rangetop must be
clear of any obstruction. For proper operation
and servicing, a clear area of at least 36" (914)
in front of the rangetop is recommended.
Your kitchen must provide an adequate supply
of fresh air to assure proper combustion and
ventilation. For the gas rangetop, fresh air
intakes are located below the bullnose and
control knobs. Never block the fresh air
intakes, as they provide air required for proper
operation. Refer to the illustration below.
Due to the high volume of ventilation air
required, a source of outside replacement air is
recommended. This is particularly important
for tightly sealed and insulated homes. A
qualified HVAC contractor should be consulted.
ACCESSORIES
Optional acces-
sories are available
through your
Wolf dealer. To
obtain local dealer
information, visit
the Locator section
of our website,
wolfappliance.com.
Keep combustibles such as solvents,
cleaning fluids, mops and rags, away from
the area surrounding all gas appliances.
Location of fresh air intakes
VENTILATION OPTIONS
IMPORTANT NOTE: It is recommended that
you operate the Wolf gas rangetop with a Pro
ventilation hood. Contact your Wolf dealer for
details.
Pro Wall Hood – 22" (559), 24" (610) or 27"
(686) depths and 30" (762) to 66" (1676)
widths in classic stainless steel.
Pro Island Hood – 36" (914) to 66" (1676)
widths in classic stainless steel.
Pro Hood Liner – available in widths to
accommodate 30" (762) to 60" (1524) hood
shells.
All Pro ventilation hoods have welded seams,
sealed halogen lighting and removable, dish-
washer-safe stainless steel filters.
Blower requirements may vary due to length
of duct work and number of angles. The basic
recommendation is 1 CFM per 100 Btu/hr.
Always consult your HVAC professional for
more concise blower requirements.
IMPORTANT NOTE: When installing a ventila-
tion hood, refer to the specific requirements
of the hood for the minimum dimension to
countertop.
Fresh Air Intakes

6
WOLF GAS RANGETOPS
MINIMUM CLEARANCES
IMPORTANT NOTE: Caution must be used in
planning the proper installation of the Wolf gas
rangetop to avoid fires or damage to adjacent
cabinetry or kitchen equipment. Be sure to
follow the minimum clearances established in
the finished rough opening dimensions.
Refer to the Installation Specifications
illustrations for your model on pages 8–9 for
the exact rough opening dimensions.
WALL INSTALLATIONS
Minimum clearances to combustible
surfaces:
Minimum 18" (457) clearance from bottom
of upper cabinet to countertop, within 6"
(152) minimum side clearance.
Minimum spacing between overhead side
cabinets must be greater than or equal to
the nominal width of the rangetop. The
maximum depth of overhead and side
cabinets is 13" (330), within 6" (152) side
clearance.
0" (0) clearance for adjacent combustible
materials below the countertop, both sides
and rear.
Bottom of ventilation hood must be 30"
(762) minimum to 36" (914) maximum from
countertop.
INSTALLATION SPECIFICATIONS
Wolf gas rangetops come in 36" (914) and 48"
(1219) widths. Illustrations on pages 8–9
provide the overall dimensions and installation
specifications for each width of gas rangetop.
Refer to the Installation Specifications illustra-
tion for your model on pages 8–9 for the exact
rough opening dimensions and location of the
gas and electrical supply.
IMPORTANT NOTE: Cabinet opening dimen-
sions shown in the Installation Specifications
illustrations must be used. These dimensions
provide for required clearances.

MINIMUM CLEARANCES
WALL INSTALLATIONS
Minimum clearances for gas rangetops
without a ventilation hood:
Surface Burners or Griddle (G) Models:
30" (762) minimum vertical distance from
countertop to combustible materials above
the rangetop.
Charbroiler (C) Models: 36" (914) minimum
vertical distance from countertop to
combustible materials above the rangetop.
ISLAND | PENINSULA INSTALLATIONS
Minimum clearances to combustible
surfaces:
Island Installations: Minimum 12" (305)
clearance to rear wall that rises above the
countertop.
Peninsula Installations: Minimum 6" (152)
clearance to side walls and minimum 12"
(305) clearance to rear wall that rises above
the countertop.
Refer to the Installation Specifications
illustrations for your model on pages 8–9 for
the exact rough opening dimensions.
7
Dimensions in parentheses are in
millimeters unless otherwise specified.
INSTALLATION INSTRUCTIONS
Failure to locate the rangetop without
the proper clearances will result in a fire
hazard.
RISER REQUIREMENTS
Installations against a combustible surface:
The 101/2"(267) riser is required for all gas
rangetops in non-island applications installed
against a combustible surface.

8
WOLF GAS RANGETOPS
IMPORTANT NOTE:
For 36" (914) gas
rangetops, a riser is
required for all
models in non-island
applications
installed against a
combustible surface.
14"
(356)
8" (203)
361/4"(921)
FINISHED ROUGH OPENING WIDTH
3/4"(19) PLATFORM
TOP VIEW
OF PLATFORM
EG
8" (203)
3"(76)
BACK WALL
1/2"
(13)
23/4"
(70)
ISLAND INSTALLATIONS: 12" (305) MINIMUM
CLEARANCE FROM BACK OF RANGETOP TO
COMBUSTIBLE REAR WALL ABOVE COUNTERTOP–
0" (0) TONON-COMBUSTIBLE MATERIALS
3/4"(19) PLATFORM
91/2"(241)
OPENING
HEIGHT
24" (610)
13" max
(330)
36"
(914)
18"min (457)
TO COUNTERTOP
LOCATION OF
GAS AND ELECTRICAL
SUPPLY CUT-OUT
WITHIN SHADED AREA
THROUGH BOTTOM OF
PLATFORM
30"min (762)
TO 36"max (914)
COUNTERTOP
TO BOTTOM OF
VENTILATION HOOD
6"min (152)
TO
COMBUSTIBLE
MATERIALS
(BOTH SIDES)
30"min (762)
COUNTERTOP
TO COMBUSTIBLE
MATERIALS
36"min (914)
FOR CHARBROILER
VENTILATION HOOD
36" (914)
OVERALL WIDTH
20" (508)
WITH
101/2"
RISER
24" (610)
271/4"(692)
OVERALL DEPTH
TO KNOBS
23/4"(70)
13/4"
(44)
101/2"(267)
OVERALL
HEIGHT
91/2"
(241)
COOKING
SURFACE
INSTALLATION SPECIFICATIONS
OVERALL DIMENSIONS
Overall Width 36" (914)
Overall Height
(to cooking surface) 101/2"(267)
Overall Depth 271/4"(692)
Opening Width 361/4"(921)
Dimensions may vary to ±1/8"(3).
36" (914) GAS RANGETOP

9
Dimensions in parentheses are in
millimeters unless otherwise specified.
INSTALLATION INSTRUCTIONS
IMPORTANT NOTE:
For 48" (1219) gas
rangetops, a riser is
required for all
models in non-island
applications
installed against a
combustible surface.
VENTILATION HOOD
14"
(356)
16"
(406)
LOCATION OF GAS AND
ELECTRICAL SUPPLY CUT-OUT
WITHIN SHADED AREA
THROUGH BOTTOM OF
PLATFORM
TOP VIEW
OF PLATFORM
EG
16"
(406)
3"
(76) BACK WALL
1/2"
(13)
481/4"(1226)
FINISHED ROUGH OPENING WIDTH
3/4"(19) PLATFORM
6"min (152)
TO
COMBUSTIBLE
MATERIALS
(BOTH SIDES)
30"min (762)
TO 36"max (914)
COUNTERTOP
TO BOTTOM OF
VENTILATION HOOD
30"min (762)
COUNTERTOP
TO COMBUSTIBLE
MATERIALS
36"min (914)
FOR CHARBROILER
23/4"
(70)
ISLAND INSTALLATIONS: 12" (305) MINIMUM
CLEARANCE FROM BACK OF RANGETOP TO
COMBUSTIBLE REAR WALL ABOVE COUNTERTOP–
0" (0) TONON-COMBUSTIBLE MATERIALS
3/4"(19) PLATFORM
91/2"(241)
OPENING
HEIGHT
24" (610)
13" max
(330)
36"
(914)
18"min (457)
TO COUNTERTOP
48" (1219)
OVERALL WIDTH
20" (508)
WITH
101/2"
RISER
24" (610)
271/4"(692)
OVERALL DEPTH
TOKNOBS
23/4"(70)
13/4"
(44)
101/2"(267)
OVERALL
HEIGHT
91/2"
(241)
COOKING
SURFACE
INSTALLATION SPECIFICATIONS
OVERALL DIMENSIONS
Overall Width 48" (1219)
Overall Height
(to cooking surface) 101/2"(267)
Overall Depth 271/4"(692)
Opening Width 481/4"(1226)
Dimensions may vary to ±1/8"(3).
48" (1219) GAS RANGETOP

10
INSTALL THE RANGETOP
Prepare the finished rough opening for the
rangetop according to the Installation Specifi-
cations illustration for your model on pages
8–9. The platform must be 3/4"(19) thick and
include a cut-out at the back for gas supply
and electrical connections.
IMPORTANT NOTE: The platform must be
level to ensure that the cooking surface is
level.
Remove and discard all packing materials,
including cardboard and tape on the outside of
the rangetop. Remove burner grates from the
cooking surface.
If your installation requires a riser, it must be
attached to the rangetop before installation.
Refer to the installation instructions packaged
with the riser.
Position the rangetop on the platform. Gas
supply and electrical connections should be
made before the rangetop is placed in its final
position.
WOLF GAS RANGETOPS
GAS SUPPLY REQUIREMENTS
TYPES OF GAS
There are two types of gas, natural and liquid
propane (LP). Conversions are required in
order for appliances designed for one gas to be
operated with the other gas. Such conversions
must be performed by a Wolf authorized
service center. Make sure your Wolf gas
rangetop is correctly adjusted for the type of
gas being used.
The product rating plate has information on the
type of gas that should be used. The rating
plate is located under the drip pan that
supports the cooking grates, on the left inside
wall of the rangetop. The rating plate for
French Top models (except Model RT484F) is
located on the right inside wall. If this informa-
tion does not agree with the type of gas
available, contact your Wolf dealer. Toobtain
local dealer information, visit the Locator
section of our website, wolfappliance.com.

11
Dimensions in parentheses are in
millimeters unless otherwise specified.
INSTALLATION INSTRUCTIONS
GAS SUPPLY REQUIREMENTS
GAS SUPPLY CONNECTION
IMPORTANT NOTE: The gas rangetop must
be connected to a regulated gas supply.
Connect the rangetop to the gas supply line.
The gas supply line must be of adequate size
to properly service all gas appliances. If local
codes permit, a certified, 3' (.9 m) long, 1/2"
or 3/4"ID flexible metal appliance connector is
recommended for connecting this rangetop to
the gas supply line. The pipe coming off of the
unit has 1/2"female threads.
IMPORTANT NOTE: The supply line must
be equipped with an approved external gas
shut-off valve located near the rangetop in an
accessible location. Do not block access to the
shut-offvalve. Refer to the illustration below.
The Wolf gas rangetop functions up to 6,000'
(1828 m) in altitude without any adjustment. If
installation is above 6,000' (1828 m), contact
your Wolf dealer.
EXPLOSION HAZARD—
Use a certified gas supply line and install
a gas shut-off valve.
Securely tighten all gas connections.
The maximum gas supply pressure to the
regulator should never exceed 14" (34.9
mb) WC (water column); .5 psi (3.5 kPa).
Failure to do so can result in explosion,
fire or death.
Gas Supply
LineTo Appliance
SHUT-OFF VALVE
Open Position
Shut-off valve
IMPORTANT
NOTE
This installation
must conform with
local codes and
ordinances. In the
absence of local
codes, installations
must conform with
the American
National Standard,
National Fuel Gas
Code.
Before connecting the gas supply, make
sure all valves are in a closed position. Do
not connect the gas supply to an appli-
ance that shows any sign of physical
damage.

GAS LEAK TESTING
Use a brush and liquid detergent to test all gas
connections for leaks. Bubbles around connec-
tions will indicate a leak. If a leak appears, shut
off the gas valve and adjust connections. Then
check connections again. Clean all the deter-
gent solution from the rangetop.
Never test for a gas leak with a match or
other flame.
GAS SUPPLY REQUIREMENTS
GAS MANIFOLD PRESSURE
For Natural Gas: Standard orifices
are set for 5" (12.5 mb) WC (water column).
Anatural gas pressure regulator is
installed.
For Propane (LP) Gas: Standard orifices
are set for 10" (25 mb) WC (water column).
Apropane gas pressure regulator is
installed.
Gas Supply Pressure: For checking the
regulator setting, the maximum line
pressure for natural and propane (LP) gas:
14" (34.9 mb) WC; .5 psi (3.5 kPa). Minimum
line pressure for natural gas: 7" (17.5 mb)
WC. Minimum line pressurefor propane
(LP) gas: 11" (27.4 mb) WC.
Gas Supply Regulator: To control and
maintain a uniformgas pressurein the gas
manifold, the unit must be used with a gas
pressure regulator. The burner orifices, etc.
aresized for the gas pressuredelivered by
the supplied regulator. Do not remove the
regulator.
The maximum gas supply pressureto
the regulator should never exceed 14"
(34.9 mb) WC; .5 psi (3.5 kPa).
12
WOLF GAS RANGETOPS

13
Dimensions in parentheses are in
millimeters unless otherwise specified.
INSTALLATION INSTRUCTIONS
ELECTRICAL SHOCK HAZARD –
Plug into a grounded 3-prong outlet.
Do not remove ground prong.
Do not use an adapter.
Failure to follow these instructions can
result in electric shock, fire or death.
The Wolf gas rangetop requires a 110/120 V AC
electrical supply to operate the electronic
ignition system. The 6' (1.8 m) power supply
cord provided with the rangetop is equipped
with a 3-prong, grounded plug for protection
against shock hazard. The service should have
its own 15 amp circuit breaker.
IMPORTANT NOTE: You must follow all
National Electrical Code and gas regulations.
In addition, be aware of local codes and ordi-
nances when installing your services.
IMPORTANT
NOTE
You must follow
all National
Electrical Code
regulations. In
addition, be aware
of local codes and
ordinances when
installing your
service.
RECOMMENDED GROUND METHOD
IMPORTANT NOTE: This appliance must be
properly grounded to avoid shock hazard.
The rangetop is equipped with a 3-prong
ground plug. To minimize possible shock
hazard, the cord must be plugged into a
mating 3-prong ground-type outlet, grounded
to conform with the National Electrical Code,
ANSI/NFPA 70 latest edition, or Canadian
Electrical Code (CSA) and all local codes and
ordinances. Refer to the illustration below.
IMPORTANT NOTE: You must have a properly
grounded, 3-prong outlet installed by a quali-
fied electrician. A ground fault circuit inter-
rupter (GFCI) is not recommended and may
cause interruption of operation.
IMPORTANT NOTE: Do not ground to a gas
pipe.
WIRING DIAGRAM
The wiring diagram covering the control circuit
is located under the drip pan that supports the
cooking grates, on the left inside wall of the
rangetop. The wiring diagram for French Top
models (except Model RT484F) is located on
the right inside wall.
ELECTRICAL REQUIREMENTS
Grounding Plug
Grounding-Type
Electrical Outlet
Electrical ground

REMOVING THE RANGETOP
Ifremoving the gas rangetop is necessary for
cleaning or service, shut off the gas supply.
Disconnect the gas supply and electrical
connections to the unit, then remove the
rangetop. Reinstall in the reverse order and be
sure to check the gas connection for leaks.
Refer the Wolf Gas Rangetops Use & Care
Information included with the rangetop for
cleaning recommendations.
Be sure to disconnect the gas supply and
electrical connections before removing
the rangetop.
14
WOLF GAS RANGETOPS
TROUBLESHOOTING
IMPORTANT NOTE: If the gas rangetop
does not operate properly, follow these
troubleshooting steps:
Verify that power is being supplied to the
rangetop.
Check the gas supply and electrical
connections to ensure that the installation
has been completed correctly.
Check that gas valves are turned to the ON
position.
Check polarity of the electrical outlet should
nuisance clicking of igniters occur after a
burner is lit.
If the rangetop still does not work, contact a
Wolf authorized service center.Do not
attempt to repair the rangetop yourself.
Wolf is not responsible for service required
to correct a faulty installation.

15
CONTACT
INFORMATION
Wolf Customer
Service:
800-332-9513
Website:
wolfappliance.com
INSTALLATION INSTRUCTIONS
The information and images are the copyright
property of Wolf Appliance Company, LLC, an
affiliate of Sub-Zero Freezer Company, Inc.
Neither this book nor any information or images
contained herein may be copied or used in whole
or in part without the express written permission
of Wolf Appliance Company, LLC, an affiliate of
Sub-ZeroFreezer Company,Inc.
©Wolf Appliance Company, LLC all rights reserved.
IF YOU NEED SERVICE
If service is necessary, maintain the quality
built into your gas rangetop by calling a
Wolf authorized service center.
Toobtain the name and number of a
Wolf authorized service center, check
the Locator section of our website,
wolfappliance.com orcall Wolf Customer
Service at
800-332-9513 .
When calling for service, you will need the
gas rangetop model and serial numbers.
Both numbers are listed on the product
rating plate. The rating plate is located
under the drip pan that supports the
cooking grates, on the left inside wall of the
rangetop. The rating plate for French Top
models (except Model RT484F) is located on
the right inside wall.

807584 3/2006
WOLF APPLIANCE COMPANY, LLC P.O. BOX 44848 MADISON, WI 53744 800-332-9513 WOLFAPPLIANCE.COM