TV Logic LVM-170A User manual

Multi Format Broadcast
LCD Monitor
OperationManual_v4.1
LVM-170A
LVM-176W
LVM-182W-A
LVM-232W-A
LVM-246W

Multi Format LCD Monitor 3
Contents
1. Caution
2. Main Features
3. Controls & Functions
4. Menu Organization & Adjustment
5. Menu Operations
[1] PICTURE
[2] COLOR
[3] MARKER
[4] GPI/UMD
[5] WAVEFORM
[6] AUDIO
[7] DISPLAY & SET
6. Firmware Upgrage
7. Button Functions
8. Other Functions
9. DVI / HDMI Support Resolution
10. Product Specications
11. Optional Accessories
04
06
07
18
23
24
26
26
28
33
36
38
41
42
45
53
55
60
FCC(FederalCommunicationsCommission)
ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforclassAdigitaldevice,pursuanttopart15
oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterfacewhenthe
equipmentisoperatedinacommercialenvironment.
Thisequipmentgenerates,usesandcanradiateradiofrequencyenergyandifnotinstalledandusedin
accordancewiththeinstructionmanual,maycauseharmfulinterferencetoradiocommunications.Operationof
thisequipmentinaresidentialtocorrecttheinterferenceathisownexpense
CAUTION:Changeormodificationsnotexpresslyapprovedbythemanufacturerresponsibleforcompliance
couldvoidtheuser’sauthoritytooperatetheequipment.
DisposalofOldElectrical&ElectronicEquipment
(ApplicableintheEuropeanUnionandotherEuropeancountrieswithseparatecollectionsystems)
Thissymbolontheproductoronitspackingindicatesthatthisproductshallnotbetreatedashousehold
waste.Insteaditshallbehandedovertotheapplicablecollectionpointfortherecyclingofelectricaland
electronicequipment.Byensuringthisproductisdisposedofcorrectly,youwillhelppreventpotentialnegative
consequencefortheenvironmentandhumanhealth,whichcouldotherwisebecausedbyinappropriatewaste
handlingofthisproduct.Therecyclingofmaterialswillhelptoconservenaturalresources.
.......................................................................................
..............................................................................
....................................................................
.................................................
.........................................................................
.................................................................................
...................................................................................
.................................................................................
...............................................................................
.............................................................................
....................................................................................
........................................................................
........................................................................
..........................................................................
............................................................................
....................................................
...............................................................
.................................................................

4 Multi Format LCD Monitor Multi Format LCD Monitor 5
1. Caution 1. Caution
●Always use set voltage.
●AC 100 ~ 240V (1.6A/50~60Hz)
●LVM-170A : DC 12/24V(MAX 6A)
●LVM-176W : DC 12/24V(MAX 6A)
●LVM-182W-A : DC 24V(MAX 1.3A)
●LVM-232W-A : DC 12V (MAX 0.3A)
●LVM-246W : DC 12V (MAX 6A)
• All operating instructions must be read and
understood before the product is operated.
• These safety and operating instructions must
be kept in safe place for future reference.
• All warnings on the product and in the
instructions must be observed closely.
• All operating instructions must be followed.
• Do not use attachments not recommended
by the manufacturer. Use of inadequate
attachments can result in accidents.
• This product must be operated on a power
source specied on the specication label.
If you are not sure of the type of power supply
used in your home, consult your dealer or local
power company. For units designed to operate
on batteries or another power source, refer to
the operating instructions.
• The power cords must be routed properly
to prevent people from stepping on them or
objects from resting on them. Check the cords
at the plugs and product.
• In case of using other DC 12V/24V (LVM-176W),
12V (LVM-246W)adapters instead of the
standard adapter provided by the
manufacturer, please check the proper load
capacity (or current capacity) and use an
adapter with stable voltage.
• Do not overload AC outlets or extension cords.
Overloading can cause re or electric shock.
• Never insert an object into the product
through vents or openings. High voltage ows
in the product, and inserting an object can
cause electric shock and/or short internal parts.
For the same reason, do not spill water or liquid
on the product.
• Do not attempt to service the product yourself.
Removing covers can expose you to high
voltage and other dangerous conditions.
Request a qualied service person to perform
servicing.
• If any of the following conditions occurs,
unplug the power cord from the AC outlet, and
request a qualied service person to perform
repairs.
a. When the power cord or plug in damaged.
b. When a liquid was spilled on the product or
when objects have fallen into the product.
c. When the product has been exposed to rain
or water.
d. When the product does not operate properly
as described in the operating instructions. Do
not touch the controls other than those
described in the operating instructions.
Improper adjustment of controls not described
in the instructions can cause damage, which
often requires extensive adjustment work by a
qualied technician.
e. When the product has been dropped or
damaged.
f. When the product displays an abnormal
condition. Any noticeable abnormality in
the product indicates that the product needs
servicing.
• In case the product needs replacement parts,
make sure that the service person uses
replacement parts specied by the
manufacturer, or those with the same
characteristics and performance as the original
parts. Use of unauthorized parts can result in
re, electric shock and/or other danger.
• Upon completion of service or repair work,
request the service technician to perform safety
checks to ensure that the product is in proper
operating condition.
• When mounting the product on a wall or
ceiling, be sure to install the product
according to the method recommended by the
manufacturer.
• Unplug the power cord from the AC outlet
before cleaning the product. Use a damp cloth
to clean the product. Do not use liquid cleaners
or aerosol cleaners.
• Unplug the power cord from the AC outlet if
you do not use the product for considerably
long time.
• Do not use the product near water, such as
bathtub, washbasin, kitchen sink and laundry
tub, swimming pool and in a wet basement.
• Keep the product away from direct rays of the
Sun-light.
• Do not place the product on an unstable cart,
stand, tripod or table. Placing the product on
an unstable base can cause the product to fall,
resulting in serious personal injuries as well as
damage to the product. Use only a cart, stand,
tripod, bracket or table recommended by the
manufacturer or sold with the product. When
mounting the product on a wall, be sure to
follow the manufacturer’s instruction. Use only
the mounting hardware recommended by the
manufacturer.
• When relocating the product placed on a cart,
it must be moved with the utmost care.
Sudden stops, excessive force and uneven oor
surface can cause the product to fall from the
cart.
• The vents and other openings in the cabinet
are designed for ventilation. Do not cover or
block these vents and openings since
insucient ventilation can cause overheating
and/or shorten the life of the product. Do not
place the product on a bed, sofa, rug or other
similar surface, since they can block ventilation
openings. This product is not designed for
built-in installation; do not place the product
in an enclosed place such as a bookcase or
rack, unless proper ventilation is provided or
the manufacturer’s instructions are followed.
• The LCD panel used in this product is made of
glass. Therefore, it can break when the product
is dropped or applied with impact. Be careful
not to be injured by broken glass pieces in case
the LCD panel breaks.
• Keep the product away from heat sources
such as radiators, heaters, stoves and other heat
generating products (including ampliers).

6 Multi Format LCD Monitor Multi Format LCD Monitor 7
●Compatible with varied SDI signals
- The product is compatible with varied
SD/HD/3G(A/B)-SDI 480i,576i,720p,1080i/p,
1080psf.
●Compatible with analog signals
- The product is compatible with analog
signals - Composite
●HDMI/DVI Digital(HDCP) / Analog input
support
- HDMI, DVI digital/analog(VGA) input is
available without any other accessories.
●All-in-one type system
- Slim and all-in-one type monitor that
requires no other accessories and optimized
for space utilization.
●Waveform/Vector Scope/Luma(Y’) zone
check/Audio Level Meter support
- Waveform & Vector Scope support
- Luma(Y’) zone check support(False color)
- Embedded Audio Level Meter support
●Luma(Y’) zone check(Color/Zebra type)/
Range error function
●Audio in & out
- built-in internal speaker (Embedded audio &
External audio in)
- Stereo audio out using phone jack & external
audio in.
●Knob Control
- Easy to adjust user conguration using the
control knobs.
●BLUE ONLY/MONO/Focus-Assist/H/V delay
●Internal pattern generator(0~100% Gray/
Colorbar+Pluge)
●Varied Markers & Safety Areas
- Center Marker, Safety Area Marker, Aspect
Marker, Display Size(Scan)
●1:1 SCAN / Zoom
- Outputs the original signal image on the
screen without scaling.
- Outputs the original signal image with
zoom-in.
- Zoom scroll function (left/right/up/down).
●Wide screen compatible
- Wide screen for 16:9 aspect monitoring.
(LVM-170A/LVM-176W / 182W-A)
- Native Wide screen for 16:9 aspect
monitoring. (LVM-232W-A / 246W)
●AC/DC Compatible
- Basically, this product is powered by a
normal AC source, and is also compatible
with DC.
- DC 12V : LVM-246W
●Remote control function
- The product can be remotely controlled
using external switch or RS-422
communication.
●RS422/UMD feature support
- This product supports protocols provided by
TVLogic or a TSL protocol.
●Additional Features
- Wide Viewing Angle, Loop Through (SDI/
Analog), VESA mounting, Easy to operate
OSD user interface, Rack Mountable Design.
- LVM-170A : 700:1 contrast, 300cd/㎡
Brightness
- LVM-182W-A/232/246W : 1000:1, 300cd/㎡
Brightness
- LVM-176W : 900:1, 350cd/㎡
LVM-170A/176W/182W-A/232W-A/246W Monitors contain the following features:
2. Main Features
LVM-170A : FRONT
LVM-170A : REAR
3. Controls & Functions
F1
F2
F3
F4
F5
SDI-B
SDI-A
DIGITAL
ANALOG
USB
INFO.
BLUE ONLY
H/V DELAY
MARKER
ASPECT
SCAN
ENTER/UP/DOWN
POWER
PHONE JACK
HDMI
CVBS
DVI-I
SDI-A IN
SDI-B IN
SDI OUT
LAN OUT
LAN IN
AUDIO IN
REMOTE
RS-422 OUT
RS-422 IN
AC IN
POWER S/W
DC IN
MENU/EXIT
F1
F2
F3
F4
F5
SDI-B
SDI-A
DIGITAL
ANALOG
USB
INFO.
BLUE ONLY
H/V DELAY
MARKER
ASPECT
SCAN
ENTER/UP/DOWN
POWER
PHONE JACK
HDMI
CVBS
DVI-I
SDI-A IN
SDI-B IN
SDI OUT
LAN OUT
LAN IN
AUDIO IN
REMOTE
RS-422 OUT
RS-422 IN
AC IN
POWER S/W
DC IN
MENU/EXIT

8 Multi Format LCD Monitor Multi Format LCD Monitor 9
3. Controls & Functions 3. Controls & Functions
LVM-170A : FRONT LVM-170A : FRONT
●[MARKER] Button/Lamp
- Used to activate/deactivate the Marker.
- The Marker is normally displayed when you
select Aspect ratio you want in OSD Menu.
●[H/V DELAY] Button/Lamp
- Used to check horizontal sync. and vertical
sync. simultaneously.
●[BLUE ONLY/MONO] Button/Lamp
- Press the button to remove red and green
from the input signal and display the screen
only under a blue signal. Press the button
again to activate mono mode.
- This function is not activated in the RGB, DVI
ANALOG, DVI DIGITAL, HDMI modes.
●[INFO.] Button
- Displays the current function and setting of
the monitor.
●[USB]
- Updates new rmware and color calibration.
●[ANALOG] Button/Lamp
- Used to select desired Analog input.
- Press the button to activate the analog
input menu-selection, then use UP
and DOWN button to select desired input.
* Please refer to “7. Button Functions [1]
ANALOG Button” for more information.
●
●[DIGITAL] Button/Lamp
- Used to select desired Digital input. (HDMI,
DVI Digital)
- Press the Digital Button to activate the
Digital input menu-selection, then use the
Knob to select desired input.
*Please refer to “7. Button Functions [2]
DIGITAL” for more information.
●[SDI-A] Button/Lamp
- Used to select SDI-A input.
●[SDI-B] Button/Lamp
- Used to select SDI-B input.
●[F1 ~ F5] Button/Lamp
- Performs the function that the user set as
hot-keys.
- The selectable the hot-key menu comes up
when you hold the keys. You can select the
hot-key functions from it.
●[SCAN] Button/Lamp
- Used to change the scan mode. Press the
button to activate through the scan modes:
OVER SCAN > ZERO SCAN > UNDER SCAN >
1:1 SCAN > FIT WIDTH
*Please refer to “8. Other Functions [1]SCAN”
for more information.
●[ASPECT] Button/Lamp
- Used to change the display ratio between
4:3 and 16:9.
- Activates in the order of [16:9]-[4:3]-[2.35:1]-
[1.85:1]-[15:9]-[16:10] -[AUTO]-[16:9].
●[MENU/EXIT] Button/Lamp
- Activates OSD menu.
●[ENTER/UP/DOWN] Knob
- Used to conrm a chosen value.
- Used to move the cursor in OSD menu.
●[POWER] Button/Lamp
- Turns on or o the monitor power.
●[OPERATE] Lamp
- Indicates the status of power connection and
monitor operation.
- The LED is o with power o.
- The LED is red when the monitor is in waiting
mode with power on.
- The LED is green when the monitor is
operating.
●[AUDIO OUT] (Phone jack)
- Outputs dis-embedded audio signal, HDMI
audio signal or stereo signal from outside
through internal speaker or phone jack.
●[TALLY] Lamp
- Tally lamp that can be toggled in green or
red using the REMOTE(RJ-45) port.

10 Multi Format LCD Monitor Multi Format LCD Monitor 11
LVM-176W : FRONT
LVM-176W : REAR
LVM-176W : REAR
3. Controls & Functions3. Controls & Functions
POWER
ANALOG
SDI-A
SDI-B
DIGITAL
SCAN
ASPECT
MARKER
ENTER
UP/DOWN
MENU
WAVEFORM
PHASE
BLUE ONLY/MONO
H/V DELAY
APERTURE
BRIGHT
CHROMA
CONTRAST
VOLUME
CVBS1/G/Y/S-Y
HDMI
CVBS2/B/Pb
CVBS3/R/Pr/S-C
DVI-I
SDI-A IN
SDI-B IN
SDI OUT
USB
AUDIO OUT
AUDIO IN
REMOTE
RS-422 OUT
RS-422 IN
POWER S/W
AC IN
DC IN
POWER
ANALOG
SDI-A
SDI-B
DIGITAL
SCAN
ASPECT
MARKER
ENTER
UP/DOWN
MENU
WAVEFORM
PHASE
BLUE ONLY/MONO
H/V DELAY
APERTURE
BRIGHT
CHROMA
CONTRAST
VOLUME
CVBS1/G/Y/S-Y
HDMI
CVBS2/B/Pb
CVBS3/R/Pr/S-C
DVI-I
SDI-A IN
SDI-B IN
SDI OUT
USB
AUDIO OUT
AUDIO IN
REMOTE
RS-422 OUT
RS-422 IN
POWER S/W
AC IN
DC IN
●[HDMI(HDCP)] (HDMI)
- Signal input terminal for HDMI signal.
●[CVBS] (BNC)
- Signal input terminal for COMPOSITE signal.
●[SDI-IN A] (BNC)
- Signal input terminal for 3G/HD/SD SDI
signal.
●[SDI-IN B] (BNC)
- Signal input terminal for 3G/HD/SD SDI
signal.
●[SDI-OUT] (BNC)
- Signal output terminal for 3G/HD/SD SDI
input signal through SDI-IN.
●[LAN]
- Supports TVLogic’s control program
(observer). (rmware update/ Status
Save&Load / LUT Save&Load )
●[Audio in] (PHONE JACK)
- Inputs external audio.
●[RS422 IN/OUT] (RJ-45)
- Controls the monitor by a protocol provided
by TVLogic or supports TSL protocol.
●~ AC IN
- 100 ~ 240V AC 50/60Hz
●DC 12V IN
- 12V /24V DC
<WARNING!!>
When using the product make sure to ground,
whenever possible, before connecting the
input signal cable in order to prevent any
possible damage to the product or connected
devices. The damage may include signal noise,
malfunction of main board or display panel.
And the connected devices such as camera
or video source player may also be inuenced
through signal cable. Please check if the AC
power source and the power extender or
power distributor is grounded.
DC IN socket
1,2 : GND
3,4 : +12V / +24V

12 Multi Format LCD Monitor Multi Format LCD Monitor 13
3. Controls & Functions
LVM-176W : FRONT
●[MARKER] Button/Lamp
- Used to activate/deactivate the Marker.
- The Marker is normally displayed when you
select Aspect ratio you want in OSD Menu.
●[H/V DELAY] Button/Lamp
- Used to check horizontal sync. and vertical
sync. simultaneously.
●[BLUE ONLY/MONO] Button/Lamp
- Press the button to remove red and green
from the input signal and display the screen
only under a blue signal. Press the button
again to activate mono mode.
- This function is not activated in the RGB, DVI
ANALOG, DVI DIGITAL, HDMI modes.
●[PHASE] Button/Lamp
- Activates in the order of CHROMA, PHASE,
Closed Caption, while OSD menu is not
activated, and you can toggle through the
values by UP/DOWN keys. Toggling order is
as below depending on input signal.
- SDI-A/B modes : CHROMA > Closed Caption.
- Component mode : CHROMA.
- Composite/S-Video modes : CHROMA >
PHASE > Closed Caption.
- DVI-Analog mode : PHASE.(AUTO PHASE)
●[WAVE FORM] Button/Lamp
- Activates Waveform or Vector scope of input
signal.
- Operating change order is WAVE FORM
> VECTOR SCOPE > WAVE FORM WIDE >
WAVE FORM YCbCr > WAVE_VECTOR > FULL
WAVEFORM(Y) > FULL VECTORSCOPE.
*Please refer to “8. Other Functions [3]
WAVEFORM” for more information.
●[OPERATE] Lamp
- Indicates the status of power connection and
monitor operation.
- The LED is o with power o.
- The LED is red when the monitor is in waiting
mode with power on.
- The LED is green when the monitor is
operating.
●[POWER] Button/Lamp
- Turns on or o the monitor power.
●[ANALOG] Button/Lamp
- Used to select desired Analog input.
- Press the button to activate the analog
input menu-selection, then use UP
and DOWN button to select desired input.
* Please refer to “7. Button Functions [1]
ANALOG Button” for more information.
●[DIGITAL] Button/Lamp
- Used to select desired Digital input. (HDMI,
DVI Digital)
- Press the Digital Button to activate the
Digital input menu-selection, then use the
Knob to select desired input.
*Please refer to “7. Button Functions [2]
DIGITAL” for more information.
●[SDI-A] Button/Lamp
- Used to select SDI-A input.
●[SDI-B] Button/Lamp
- Used to select SDI-B input.
●[SCAN] Button/Lamp
- Used to change the scan mode. Press the
button to activate through the scan modes:
OVER SCAN > ZERO SCAN > UNDER SCAN >
1:1 SCAN > FIT WIDTH
*Please refer to “8. Other Functions [1]SCAN”
for more information.
●[ASPECT] Button/Lamp
- Used to change the display ratio between
4:3 and 16:9.
- Activates in the order of [16:9]-[4:3]-[2.35:1]-
[1.85:1]-[15:9]-[16:10] -[AUTO]-[16:9].
3. Controls & Functions
LVM-176W : FRONT
●[MENU] Button/Lamp
- Activates OSD menu.
●[DOWN] Button/Lamp
- Used to move the cursor down while OSD
menu is activated and to decrease the value
of the selected feature.
●[UP] Button/Lamp
- Used to move the cursor up while OSD menu
is activated and to increased the value of the
selected feature.
●[ENTER] Button/Lamp
- Used to conrm a chosen value.
- Volume window is activated when OSD
menu is not activated. You can adjust the
volume value with UP/DOWN keys.
- Used to move the picture position in
order in 1:1 SCAN mode, when a original
image is bigger than resolution. Please refer
to “8. Other functions [1]SCAN mode” for
more information.
●[OPERATE] Lamp
- Indicates the status of power connection and
monitor operation.
- The LED is o with power o.
- The LED is red when the monitor is in waiting
mode with power on.
- The LED is green when the monitor is
operating.
●[POWER] Button/Lamp
- Turns on or o the monitor power.
●[APERTURE] Knob
- Used to adjust the picture sharpness. The
value is selectable between 0~24.
- It is not available in DVI ANALOG.
●[BRIGHT] Knob
- Used to adjust the degree of brightness. The
value is selectable between -100~100.
●[CHROMA] Knob
- Used to adjust the saturation of the image.
The value is selectable between -50~50.
- It is not available in RGB, DVI ANALOG, DVI
DIGITAL, HDMI.
●[CONTRAST] Knob
- Used to adjust the contrast. The value is
selectable between -100~100.
●[VOLUME] Knob
- Used to adjust the volume for internal
speaker and external output. The value is
selectable between 0~30.
●[TALLY] Lamp
- Tally lamp that can be toggled in green or
red using the REMOTE(RJ-45) port.

14 Multi Format LCD Monitor Multi Format LCD Monitor 15
3. Controls & Functions
LVM-176W : REAR
●[Audio in & out] (PHONE JACK)
- Outputs dis-embedded audio signal,
HDMI audio signal or stereo signal from
outside through internal speaker or phone
jack.
●[USB]
- Updates new rmware and color calibration.
●~ AC IN
- 100 ~ 240V AC 50/60Hz
●DC 12V/24V IN
- 12V/24V DC
<Video input>
The way to input analog video signal.
<Warning!!>
When using the product make sure to ground,
whenever possible, before connecting the
input signal cable in order to prevent any
possible damage to the product or connected
devices. The damage may include signal
noise, malfunction of main board or display
panel. And the connected devices such as
camera or video source player may also
be inuenced through signal cable. Please
check if the AC power source and the power
extender or power distributor is grounded.
●[REMOTE] (RJ-45)
- Provides connection to control equipment
for external monitor control.
- Features can be changed in the [REMOTE]
section of OSD menu.
●[RS422 IN/OUT] (RJ-45)
- Controls the monitor by a protocol provided
by TVLogic or supports TSL protocol.
●[DVI-I] (DVI-I)
- Signal input terminal for DVI ANALOG or DVI
DIGITAL signal.
●[HDMI(HDCP)] (HDMI)
- Signal input terminal for HDMI signal.
●[CVBS1/Y/G/S-Y] (BNC)
- Signal input terminal for COMPOSITE 1,
S-VIDEO Y, COMPONENT Y, RGB G signal.
●[CVSBS2/Pb/B] (BNC)
- Signal input terminal for COMPOSITE 2, RGB
B, COMPONENT Pb signal.
●[CVSBS3/Pr/R/S-C] (BNC)
- Signal input terminal for COMPOSITE 3,
S-VIDEO C, COMPONENT Pr, RGB R signal.
●[SDI-IN A] (BNC)
- Signal input terminal for 3G/HD/SD SDI
signal.
●[SDI-IN B] (BNC)
- Signal input terminal for 3G/HD/SD SDI
signal.
●[SDI-OUT] (BNC)
- Signal output terminal for 3G/HD/SD SDI
input signal through SDI-IN.
Connector Composite Component S-Video
1CVBS1 Y G Y
2CVBS2 Pb BNo Con.
3CVBS3 Pr R C
DC IN socket
1,2 : GND
3,4 : +12V / +24V
3. Controls & Functions
F1
F2
F3
F4
F5
SDI-B
SDI-A
DIGITAL
ANALOG
INPUT SIGNAL
INDICATOR
INFO.
BLUE ONLY
H/V DELAY
MARKER
ASPECT
SCAN
ENTER/UP/DOWN
POWER
PHONE JACK
USB
SPEAKER
HDMI
CVBS
DVI-I
SDI-A IN
SDI-B IN
SDI OUT
AUDIO IN
REMOTE
RS-422 OUT
RS-422 IN
POWER S/W
AC IN
DC IN
MENU/EXIT
F1
F2
F3
F4
F5
SDI-B
SDI-A
DIGITAL
ANALOG
INPUT SIGNAL
INDICATOR
INFO.
BLUE ONLY
H/V DELAY
MARKER
ASPECT
SCAN
ENTER/UP/DOWN
POWER
PHONE JACK
USB
SPEAKER
HDMI
CVBS
DVI-I
SDI-A IN
SDI-B IN
SDI OUT
AUDIO IN
REMOTE
RS-422 OUT
RS-422 IN
POWER S/W
AC IN
DC IN
MENU/EXIT
LVM-182W-A/232W-A : FRONT
LVM-182W-A/232W-A : REAR

16 Multi Format LCD Monitor Multi Format LCD Monitor 17
3. Controls & Functions 3. Controls & Functions
LVM-182W-A/232W-A : FRONT LVM-182W-A/232W-A : FRONT
●[STATUS INDICATOR] Lamp
- Used to display the current input mode.
- Input Mode
CVBS : COMPOSITE
DVI-A : DVI ANALOG
DVI-D : DVI DIGITAL
HDMI : HDMI
SDI : SDI-A / B
●[ANALOG] Button/Lamp
- Used to select desired Analog input.
- Press the button to activate the analog
input menu-selection, then use UP
and DOWN button to select desired input.
*Please refer to “7. Button Functions [1]
ANALOG Button” for more information.
●[DIGITAL] Button/Lamp
- Used to select desired Digital input. (HDMI,
DVI Digital)
- Press the Digital Button to activate the
Digital input menu-selection, then use the
Knob to select desired input.
*Please refer to “7. Button Functions [2]
DIGITAL” for more information.
●[SDI-A] Button/Lamp
- Used to select SDI-A input.
●[SDI-B] Button/Lamp
- Used to select SDI-B input.
●[F1 ~ F5] Button/Lamp
- Performs the function that the user set as
hot-keys.
- The selectable the hot-key menu comes up
when you hold the keys. You can select the
hot-key functions from it.
●[SCAN] Button/Lamp
- Used to change the scan mode. Press the
button to activate through the scan modes:
OVER SCAN > USER ASPECT > ZERO SCAN >
UNDER SCAN > 1:1 SCAN > FIT WIDTH
* Please refer to “8. Other Functions [1]SCAN”
for more information.
●[ASPECT] Button/Lamp
- Used to change the display ratio between
4:3 and 16:9.
- Activates in the order of [16:9]-[4:3]-[2.35:1]-
[1.85:1]-[15:9]-[16:10] -[AUTO]-[16:9].
●[MARKER] Button/Lamp
- Used to activate/deactivate the Marker.
- The Marker is normally displayed when you
select Aspect ratio you want in OSD Menu.
●[H/V DELAY] Button/Lamp
- Used to check horizontal sync. and vertical
sync. simultaneously.
●[BLUE ONLY/MONO] Button/Lamp
- Press the button to remove red and green
from the input signal and display the screen
only under a blue signal. Press the button
again to activate mono mode.
- This function is not activated in the RGB, DVI
ANALOG, DVI DIGITAL, HDMI modes.
●[INFO.] Button
- Displays the current function and setting of
the monitor.
●[MENU/EXIT] Button/Lamp
- Activates OSD menu.
●[ENTER/UP/DOWN] Knob
- Used to conrm a chosen value.
- Used to move the cursor in OSD menu.
●[OPERATE] Lamp
- Indicates the status of power connection and
monitor operation.
- The LED is o with power o.
- The LED is red when the monitor is in waiting
mode with power on.
- The LED is green when the monitor is
operating.
●[POWER] Button/Lamp
- Turns on or o the monitor power.
●[USB]
- Updates new rmware and color calibration.
●[AUDIO OUT] (Phone jack)
- Outputs dis-embedded audio signal, HDMI
audio signal or stereo signal from outside
through internal speaker or phone jack.
●[TALLY] Lamp
- Tally lamp that can be toggled in green or
red using the REMOTE(RJ-45) port.

18 Multi Format LCD Monitor Multi Format LCD Monitor 19
3. Controls & Functions
LVM-182-A/232W-A : REAR
●[REMOTE] (RJ-45)
- Provides connection to control equipment
for external monitor control.
- Features can be changed in the [REMOTE]
section of OSD menu.
●[RS422 IN/OUT] (RJ-45)
- Controls the monitor by a protocol provided
by TVLogic or supports TSL protocol.
●[DVI-I] (DVI-I)
- Signal input terminal for DVI ANALOG or DVI
DIGITAL signal.
●[HDMI(HDCP)] (HDMI)
- Signal input terminal for HDMI signal.
●[CVBS] (BNC)
- Signal input terminal for COMPOSITE signal.
●[SDI-IN A] (BNC)
- Signal input terminal for 3G/HD/SD SDI
signal.
●[SDI-IN B] (BNC)
- Signal input terminal for 3G/HD/SD SDI
signal.
●[SDI-OUT] (BNC)
- Signal output terminal for 3G/HD/SD SDI
input signal through SDI-IN.
●[Audio in] (PHONE JACK)
- Inputs external audio.
●~ AC IN
- 100 ~ 240V AC 50/60Hz
DC 12/24V IN
- LVM-182W-A : 24V
- LVM=232W-A : 12V/24 DC
<WARNING!!>
When using the product make sure to ground,
whenever possible, before connecting the
input signal cable in order to prevent any
possible damage to the product or connected
devices. The damage may include signal noise,
malfunction of main board or display panel.
And the connected devices such as camera
or video source player may also be inuenced
through signal cable. Please check if the AC
power source and the power extender or
power distributor is grounded.
3. Controls & Functions
F1
F2
F3
F4
SCAN
SDI-B
SDI-A
DIGITAL
ANALOG
INPUT SIGNAL
INDICATOR
ENTER
UP
DOWN
MENU
BRIGHT
CONTRAST
PHONE JACK
USB
POWER
APERTURE
TALLY
MARKER
CVBS1/G/Y/S-Y
HDMI
CVBS2/B/Pb
CVBS3/R/Pr/S-C
DVI-I
SDI-A IN
SDI-B IN
SDI OUT
AUDIO-IN
AC IN
POWER S/W
DC IN
REMOTE
RS-422 OUT
RS-422 IN
F1
F2
F3
F4
SCAN
SDI-B
SDI-A
DIGITAL
ANALOG
INPUT SIGNAL
INDICATOR
ENTER
UP
DOWN
MENU
BRIGHT
CONTRAST
PHONE JACK
USB
POWER
APERTURE
TALLY
MARKER
CVBS1/G/Y/S-Y
HDMI
CVBS2/B/Pb
CVBS3/R/Pr/S-C
DVI-I
SDI-A IN
SDI-B IN
SDI OUT
AUDIO-IN
AC IN
POWER S/W
DC IN
REMOTE
RS-422 OUT
RS-422 IN
LVM-246W : FRONT
LVM-246W : REAR
DC IN socket
1,2 : GND
3,4 : +12V / +24V

20 Multi Format LCD Monitor Multi Format LCD Monitor 21
3. Controls & Functions
LVM-246W : FRONT
●[STATUS INDICATOR] Lamp
- Used to display the current input mode.
- Input Mode
VIDEO : COMPOSITE 1/2/3
S-VID : S-VIDEO
COMP : COMPONENT
RGB : RGB
DVI-A : DVI ANALOG
DVI-D : DVI DIGITAL
HDMI : HDMI
SDI-A : SDI-A
SDI-B : SDI-B
●[ANALOG] Button/Lamp
- Used to select desired Analog input.
- Press the button to activate the analog
input menu-selection, then use UP
and DOWN button to select desired input.
*Please refer to “7. Button Functions [1]
ANALOG Button” for more information.
●[DIGITAL] Button/Lamp
- Used to select desired Digital input. (HDMI,
DVI Digital)
- Press the Digital Button to activate the
Digital input menu-selection, then use the
Knob to select desired input.
*Please refer to “7. Button Functions [2]
DIGITAL” for more information.
●[SDI-A] Button/Lamp
- Used to select SDI-A input.
●[SDI-B] Button/Lamp
- Used to select SDI-B input.
●[F1 ~ F4] Button/Lamp
- Performs the function that the user set as
hot-keys.
- The selectable the hot-key menu comes up
when you hold the keys. You can select the
hot-key functions from it.
●[SCAN] Button/Lamp
- Used to change the scan mode. Press the
button to activate through the scan modes:
OVER SCAN > USER ASPECT > ZERO SCAN >
UNDER SCAN > 1:1 SCAN > FIT WIDTH
*Please refer to “8. Other Functions [1]SCAN”
for more information.
●[MARKER] Button/Lamp
- Used to activate/deactivate the Marker.
- The Marker is normally displayed when you
select Aspect ratio you want in OSD Menu.
●[MENU] Button/Lamp
- Activates OSD menu.
●[DOWN] Button/Lamp
- Used to move the cursor down while OSD
menu is activated and to decrease the value
of the selected feature.
●[UP] Button/Lamp
- Used to move the cursor up while OSD menu
is activated and to increased the value of the
selected feature.
●[ENTER] Button/Lamp
- Used to conrm a chosen value.
- Volume window is activated when OSD
menu is not activated. You can adjust the
volume value with UP/DOWN keys.
- Used to move the picture position in
order in 1:1 SCAN mode, when a original
image is bigger than resolution.
* Please refer to “8. Other functions [1]SCAN
mode” for more information.
●[APERTURE] Knob
- Used to adjust the picture sharpness. The
value is selectable between 0~24.
- It is not available in DVI ANALOG.
●[BRIGHT] Knob
- Used to adjust the degree of brightness. The
value is selectable between -100~100.
●[CONTRAST] Knob
- Used to adjust the contrast. The value is
selectable between -100~100.
●[USB]
- Updates new rmware and color calibration.
●[OPERATE] Lamp
- Indicates the status of power connection and
monitor operation.
- The LED is o with power o.
- The LED is red when the monitor is in waiting
mode with power on.
- The LED is green when the monitor is
operating.
●[POWER] Button/Lamp
- Turns on or o the monitor power.
●[TALLY] Lamp
- Tally lamp that can be toggled in green or
red using the REMOTE(RJ-45) port.
3. Controls & Functions
LVM-246W : FRONT

22 Multi Format LCD Monitor Multi Format LCD Monitor 23
LVM-246W : REAR
●[Audio in & out] (PHONE JACK)
- Outputs dis-embedded audio signal,
HDMI audio signal or stereo signal from
outside through internal speaker or phone
jack.
●~ AC IN
- 100 ~ 240V AC 50/60Hz
●DC 12V IN
- 12V DC
<Video input>
The way to input analog video signal.
<Warning!!>
When using the product make sure to ground,
whenever possible, before connecting the
input signal cable in order to prevent any
possible damage to the product or connected
devices. The damage may include signal
noise, malfunction of main board or display
panel. And the connected devices such as
camera or video source player may also
be inuenced through signal cable. Please
check if the AC power source and the power
extender or power distributor is grounded.
●[REMOTE] (RJ-45)
- Provides connection to control equipment
for external monitor control.
- Features can be changed in the [REMOTE]
section of OSD menu.
●[RS422 IN/OUT] (RJ-45)
- Controls the monitor by a protocol provided
by TVLogic or supports TSL protocol.
●[DVI-I] (DVI-I)
- Signal input terminal for DVI ANALOG or DVI
DIGITAL signal.
●[HDMI(HDCP)] (HDMI)
- Signal input terminal for HDMI signal.
●[CVBS1/Y/G/S-Y] (BNC)
- Signal input terminal for COMPOSITE 1,
S-VIDEO Y, COMPONENT Y, RGB G signal.
●[CVSBS2/Pb/B] (BNC)
- Signal input terminal for COMPOSITE 2, RGB
B, COMPONENT Pb signal.
●[CVSBS3/Pr/R/S-C] (BNC)
- Signal input terminal for COMPOSITE 3,
S-VIDEO C, COMPONENT Pr, RGB R signal.
●[SDI-IN A] (BNC)
- Signal input terminal for 3G/HD/SD SDI
signal.
●[SDI-IN B] (BNC)
- Signal input terminal for 3G/HD/SD SDI
signal.
●[SDI-OUT] (BNC)
- Signal output terminal for 3G/HD/SD SDI
input signal through SDI-IN.
Connector Composite Component S-Video
1CVBS1 Y G Y
2CVBS2 Pb BNo Con.
3CVBS3 Pr R C
DC IN socket
1,2 : GND
3,4 : +12V
3. Controls & Functions
●You may control various functions
using MENU, UP/DOWN and ENTER
buttons on the bottom front of
the monitor.
●The product may be controlled and set
system-wise through OSD displayed on
the screen.
●Menu control sequence follows the order
below:
1. Press MENU button to bring the OSD menu
on the screen.
2. Display the desired sub menu with the UP/
DOWN button.
3. After selecting a sub menu, press ENTER to
select an item with the UP/DOWN button.
4. Press ENTER to select the desired item
(veried by highlighted eld text turning
red)
5. Press ENTER to save the new value after
adjusting the value with UP/DOWN button.
(Veried by highlighted eld returning to
default black color)
6. Press MENU to remove OSD menu from the
screen.
[1] Menu Organization
[2] Menu Adjustment
[3] Menu Adjustment Procedure
4. Menu Organization & Adjustment

24 Multi Format LCD Monitor Multi Format LCD Monitor 25
5. Menu Operations
[1] PICTURE
●Brightness
- The item controls the degree of brightness
between -100~100.
#Brightness can be adjusted by using a
control knob on the front of the monitor.
●Contrast
- The item controls contrast ratio between
-100~100.
#Contrast ratio can be adjusted by using a
control knob on the front of the monitor.
●Chroma
- The item controls saturation between -50~50.
#Chroma can be adjusted by using a control
knob on the front of the monitor.
●Phase
- The item controls phase value (Hue) between
-180~180.
#If functions only with analog video input
signal.
●Aperture
- The item controls the picture sharpness
between 0~24.
#Sharpness can be adjusted by using a control
knob on the front of the monitor.
●NTSC Setup
- The item sets NTSC IRE value for 0(Zero setup)
or 7.5 IRE.
- It is activated in COMPOSITE 1/2/3 or S-VIDEO
only NTSC signal is input.
●Key Lock
- The item locks all buttons except for power,
source change and menu button in front of
the monitor.
5. Menu Operations
[1] PICTURE (DVI ANALOG)
●Brightness
- The item controls the degree of brightness
between -100~100.
#Brightness can be adjusted by using a
control knob on the front of the monitor.
●Contrast
- The item controls contrast ratio between
-100~100.
#Contrast ratio can be adjusted by using a
control knob on the front of the monitor.
●Phase
- The item controls phase value.
#If phase is not set correctly, the image may
display artifacts and out of focus.
●Clocks/Line
- The item adjusts timing for signal sync.
#If the signal sync is not set correctly, the
image may display ickering and dropping.
●Auto Adjustment
- The item adjusts the input signal
automatically. Phase, Clocks/Line, and Image
Position are also adjusted.
#If the image does not display correctly
after the Auto Adjustment, select it again for
correct adjustment. Auto Adjustment
activates automatically when input signal
resolution changes.
●Image Position
- The items moves the picture position for up/
down/left/right.

26 Multi Format LCD Monitor Multi Format LCD Monitor 27
5. Menu Operations
[2] COLOR [3] MARKER
●Color Temp
- The item controls color temperature and
allows instant access to preset color
temperature settings of 3200K, 5600K, 6500K,
9300K and USER 1/2/3.
- Only in User1/2/3, RGB Gain, Bias(=Oset)
and Color copy are activated.
●Gain Red/Green/Blue
- The item controls red/green/blue gain value
between -256~255.
#Only in User1/2/3, it is activated.
●Bias Red/Green/Blue
- The item controls red/green/blue bias(Oset,
Black Level) value between -100~100.
#Only in User1/2/3, it is activated.
●Color Copy
- The item is used to copy pre-stored color
temperature settings into a USER1/2/3 mode.
- In USER mode, nd and select the color
temperature to be used as a starting point of
custom color temperature.
#Only in USER1/2/3, it is activated.
●Marker
- The item selects the marker type when the
MARKER is displayed on the screen.
- Marker may only be activated by pressing
the MARKER button on the front of the
monitor.
- Available marker types are OFF, 16:9, 4:3, 4:3
ON AIR, 15:9, 14:9, 13:9, 1.85:1, 2.35:1, 1.85:1 &
4:3 and USER.
●Center Marker
- The item displays the CENTER MARKER on
the screen.
- The function operates only after activating
the MARKER function by pressing the
MARKER button on the front of the monitor.
●Safety Area
- The item controls the size of the SAFETY
AREA.
- Available types are 80%, 85%, 88%, 90%,
93%, 100%, EBU ACTION 16:9, EBU GRAPHIC
16:9, EBU ACTION 14:9, EBU GRAPHIC 14:9,
EBU ACTION 4:3, EBU GRAPHIC 4:3.
- The function operates only after activating
the MARKER function by pressing the
MARKER button on the front of the monitor.
[3] MARKER
5. Menu Operations
●Fit Marker
- The item activates the FIT MARKER function.
- With FIT MARKER On the safety area is
displayed relative to the marker in use.
With FIT MARKER O the safety area is
displayed relative to the incoming source.
- FIT MARKER acts as below:
●Marker Mat
- The item darkens the area of the outside of
MARKER.
- The degrees of darkness are between O ~ 7.
- Larger value means darker the marker mat is.
●Marer Color
- The item controls the color of the MARKER
lines.
- Available colors are white, gray, black, red,
green and blue.
●Marker Thickness
- The item controls the thickness of the
MARKER lines.
- The degrees of thickness are between 1 ~ 7.
●USER Marker H1
- The item controls the position of the rst
user dened horizontal marker line.
- Marker option USER needs to be selected.
●USER Marker H2
- The item controls the position of the second
user dened horizontal marker line.
- Marker option USER needs to be selected.
●USER Marker V1
- The item controls the position of the rst
user dened vertical marker line.
- Marker option USER needs to be selected.
●USER Marker V2
- The item controls the position of the second
user dened vertical marker line.
- Marker option USER needs to be selected.
●MARKER : 4:3
●SAFETY AREA : 90%
●FIT MARKER : OFF
●MARKER : 4:3
●SAFETY AREA : 90%
●FIT MARKER : ON

28 Multi Format LCD Monitor Multi Format LCD Monitor 29
●This product provides a REMOTE
CONTROL mode. The user may connect
RJ-45 jack to the REMOTE terminal on the
rear of the unit and designate a function
for each pin.
●The default settings are as follows:
PIN 1 : SDI-A Channel
PIN 2 : SDI-B Channel
PIN 3 : HDMI Channel
PIN 4 : TALLY R
PIN 5 : TALLY G
PIN 6 : User Scan
PIN 7 is POWER ON/OFF use only, PIN 8 is GND
●The default settings are as follows
(LVM-170A) :
PIN 1 : ANALOG Channel
PIN 2 : Digital Channel
PIN 3 : SDI-A Channel
PIN 4 : SDI-B Channel
PIN 5 : TALLY R
PIN 6 : TALLY G
PIN 7 is POWER ON/OFF use only, PIN 8 is GND
- Use the ENTER button and UP/DOWN button
to set the desired function.
[4] GPI / UMD
5. Menu Operations
REM
O
TE (
R
J
-45
)
1:
P
in1
2
:
P
in2
3:
P
i
n
3
4:
P
in4
5: P
i
n5
6:
P
i
n
6
7:
P
in7
8
:
G
ND
1
8
Menu
Classi-
cation
Settable Values
PIN
1~6
NONE,
ANALOG CHANNEL,
HDMI CHANNEL,
SDI-A/B CHANNEL
TALLY RED,
TALLY GREEN,
BLUE ONLY,
UNDERSCAN,
ASPECT
HVDELAY,
16:9 MARKER,
15:9 MARKER,
14:9 MARKER,
13:9 MARKER,
4:3 MARKER,
4:3 ON AIR MARKER,
1.85:1 MARKER,
2.35:1 MARKER,
1.85:1 & 4:3 MARKER
CENTER MARKER,
SAFETY AREA 80%,
SAFETY AREA 88%,
SAFETY AREA 90%,
SAFETY AREA 93%,
SAFETY AREA 100%
Dynamic UMD,
Focus Assist,
CC608(ANC),
CC608(L21),
CC708
PIN 7 POWER ON/OFF CONTROL
PIN 8 GND
●UMD Character
- The item is used to customize the characters
for UMD.
- Alphabets, numbers and special symbols are
available.
- Maximum of 8 characters.
●UMD character color
- The item sets the color of the UMD letter.
(White,Red,Green,Yellow,Cyan,Magenta)
- The function only functions only when
[D-UMD tally type] setting is [Default],[User
color], [BG. Color],[User tally] or [User BG.].
●UMD B.G. trans.
- The item sets the transparency of UMD letter
box.
- The selectable items are
[Opaque],[50%],[85%] and [100%].
●UMD size
- The item sets the font size of UMD and the
size of UMD letter box.
- The selectable items are [Small] and [Large].
[4] GPI / UMD
5. Menu Operations
●Group ID
- The item is used to control many monitors
in each group, when control the monitors by
the protocol Tvlogic provides with
RS-422/485 communication or network.
●Monitor ID
- The item sets the ID of each monitor for the
TVLogic control protocol or DYNAMIC UMD
using RS-422/485 communication.
●RS422 baud rate
- The items sets the monitor control program
that TVLogic provides and Baud rate.
●UMD Display
- The item sets UMD, ANC and DYNAMIC UMD.
- UMD : Displays user customized characters
on screen.
- ANC: Displays characters embedded in SDI
signal.
*D-UMD(S-8C) : Displays tally signal and 8
letters that are input by TSL protocol (V3.1)
on the screen.
*D-UMD(S-16C) : Displays tally signal and 16
letters that are input by TSL protocol (V3.1)
on the screen.
*D-UMD(D-8C) : Displays a pair of tally signal
and a pair of 8 letters that are input by TSL
protocol (V3.1) on the screen.

30 Multi Format LCD Monitor Multi Format LCD Monitor 31
[4] GPI / UMD
5. Menu Operations
●D-UMD tally type
- The item sets tally operation when
D-UMD(D-8C) is set in UMD DISPLAY.
- The selectable values are DEFAULT and USER
COLOR.
* Default : Original TVLogic managing method
(VRT)
* User color : Each user can set each tally color.
- When user color is selected, TALLY1 COLOR ~
TALLY4 COLOR items are activated.
* Character : Shows tally in letter color. The
operation is same as [Default].
*B.G. color : Show tally in letter background
color. The operation is same as [Default].
*User tally : Sets the color the user wants
receiving the signal from byte0, byte1 in TSL
Protocol Control BYTE and shows tally. (O,W
hite,Red,Green,Blue,Yellow,Cyan,Magenta)
*User char. : Shows tally in letter color. The
method is same as user tally one.
*User B.G. : Show tally in letter background
color. The method is same as User tally one.
●Tally1 Color ~ Tally4 Color
- Each sets the color of TALLY1 , TALLY2,
TALLY3, TALLY4.
- The selectable colors are Red, Green, Yellow.
●B0:0 B1:0 ~ B0:1 B0:1
- The item sets the color of input condition for
byte0, byte1 in TSL Protocol Control Byte.
- The selectable colors are OFF, WHITE, RED,
GREEN, BLUE, YELLOW, CYAN, MAGENTA.
[4] GPI / UMD
5. Menu Operations
<Dynamic UMD Protocol (TSL V3.1)>
* Transmission (18 Byte) (PC or Device -> Monitor)
*[HEADER] : Display address (0~126) + 80 hex.
*[CONTROL BYTE]
bit 0 : Tally 1 (1=on, 0=o)
bit 1 : Tally 2 (1=on, 0=o)
bit 2 : Tally 3 (1=on, 0=o)
bit 3 : Tally 4 (1=on, 0=o)
bit 4 : bright data (Not used)
bit 5 : bright data (Not used)
bit 6 : reserved (Not used)
bit 7 : cleared to 0 (Not used)
* [DISPLAY DATA] : 16 displayable ASCII characters.
HEADER
(1 BYTE)
CONTROL
BYTE(1 BYTE)
DISPLAY DATA
(16 BYTE)
Tally1 CHANNEL1 Tally2 Tally3 CHANNEL1 Tally4

32 Multi Format LCD Monitor Multi Format LCD Monitor 33
[4] GPI / UMD
5. Menu Operations
Bit 1
(Tally2)
Bit 1
(Tally1) Operation
0 0 CHANNEL1
0 1 CHANNEL1
1 0 CHANNEL1
1 1 CHANNEL1
Bit 1
(Tally4)
Bit 1
(Tally3) Operation
0 0 CHANNEL1
0 1 CHANNEL1
1 0 CHANNEL1
1 1 CHANNEL1
The following appearance of UMD DISPLAY is set as D-UMD(D-8C), D-UMD TALLY TYPE
and TALLY1 ~ TALLY4 COLOR.
D-UMD TALLY TYPE USER COLOR
TALLY1 COLOR RED
TALLY2 COLOR GREEN
TALLY3 COLOR RED
TALLY4 COLOR YELLOW
CHANNEL1 CHANNEL1
●Tally Type - Default
- S-8C(Single 8 Character) & S-16C(Single 16 Character)
●D-UMD TALLY TPYE – USER COLOR
- Color selections between TALLY1 ~ TALLY4.
- D-8C(Dual 8 Character)
[5] WAVEFORM
5. Menu Operations
●Waveform type
- The item sets Waveform and Vectorscope.
- The operation order is WAVE FORM >
VECTOR SCOPE > WAVE FORM WIDE > WAVE
FORM YCbCr > WAVE_VECTOR > FULL
WAVEFORM(Y) > FULL VECTORSCOPE.
*Waveform : Displays the shape and form of
luminance level of a signal.
*Vectorscope : Displays color components of
the input signals.
It is divided into 2 kinds depending on HD
input and SD input. 100% and 75% graphics
show in a picture.
*Waveform YCbCr : Displays the components
of luminance level and Cb/Cr components of
a signal.
*Wave_Vector : Displays Waveform(Y) and
VectorScope at the same time.
*Full waveform(Y) : Displays Waveform(Y) in a
whole screen.
*Full Vectorscope : Displays Vectorscope in a
whole screen.
●Waveform Intensity
- The item controls the brightness of the
WAVEFORM/VECTOR display.
- Available values are between 1 ~ 63. The
higher the number the brighter the
waveform will be.
●Waveform Trans.
- The item controls the transparency level of
the WAVEFORM/VECTOR.
- Available values are OPAQUE and TRANS.
* If the option is set to OPAQUE, the main
OSD will overlap with the waveform/vector.
However, it will automatically display it
as transparent and goes back to opaque if
the main OSD disappears.
●Waveform Size
- The item controls the size of WAVEFORM/
VECTOR.
- Available modes are SMALL, LARGE and FULL.
●Line Waveform
- Selects if the monitor shows the whole data
from the picture or the data from a certain
line of the picture when WAVEFORM/
VECTOR functions.

34 Multi Format LCD Monitor Multi Format LCD Monitor 35
[5] WAVEFORM
5. Menu Operations
●Select Line Position
- The item is used to select and check a certain
Vertical Line in WAVEFORM/VECTOR.
- It is activated with Line Waveform item on.
- In order to select a certain Vertical Line, you
need to go to [Waveform/Vector] of [WFM/
LevelCHK] in OSD menu and select the
function and choose the Vertical Line
you want by the knob or UP/DOWN KEY.
- The range of SDI signal may change
depending on input resolution as below.
*PAL : Min. 17, Max. 522
*NTSC : Min. 23, Max. 623
*720p : Min. 26, Max. 750
*1080i : Min. 21, Max. 1123
*1080p : Min. 42, Max. 1121
- The range of HDMI/Analog signal may change
depending on output resolution as below.
*LVM-176W : Min. 0, Max. 768
LVM-182W-A : Min. 0, Max. 768
LVM-232W-A : Min. 0, Max. 1080
LVM-246W : Min. 0, Max. 1200
●Luma(Y’) Zone Check
- Analyzes Luma (Y’) of input signal and
displays the analyzed area on the screen.
- There are [Color Pattern] and [Zebra Pattern]
methods to display it.
- After every pixel Y’ level analyzing, it is
displayed with a certain color or diagonal line
in right index of the screen.
- When the pixel Y’ level is under 0%(16), it is
displayed by green color/green diagonal
line, when it is above 100%(235), it is displayed
by red color/red diagonal line. Y’ level
between 0 ~ 100% is displayed by gray level
except for selected Luma Zone.
- When [Color Pattern] method is selected,
the range is displayed as yellow(bottom 10%),
pink(5%), sky-blue(top 10%).
- When [Zebra Pattern] method is selected, the
± 5% around the selected level is displayed by
diagonal line.
●Luma(Y’) Zone Adjust
- You can change the area of yellow, pink, sky-
blue in [Color Pattern] method or diagonal
line in [Zebra Pattern] method into an area
the user wants.
- The setting area is 0 ~ 100%.
[5] WAVEFORM
5. Menu Operations
●Range Error
- Selects if you perform the functions such as
Y MAX, Y MI N, C MAX, C MIN, Y PICTURE
BLINK, C PICTURE BLINK.
- The value set at Y MAX, Y MIN, C MAX, C MIN
is displayed in WAVEFORM/VECTOR.
- When Y PICTURE BLINK or C PICTURE BLINK is
on, the picture of the part out of the value set
at Y MAX, Y MIN, C MAX, C MIN blinks.
*In the case of RGB input, Range Error is not
supported.
*See section “8. Other Functions -> [8] Range
Error” for more information.
●Y Max
- Sets the max. value of Luma (Y’) between
0~255.
- The part exceeding the set value is displayed
by red in Waveform and by blinking on the
screen.
●Y Min
- Sets the min. value of Luma (Y’) between
0~255.
- The part exceeding the set value is displayed
by red in Waveform and by blinking on the
screen.
●C Max
- Sets the max. value of Chroma (C’) between
0~255.
- The part exceeding the set value is displayed
by red in Waveform and by blinking on the
screen.
●C Min
- Sets the min. value of Chroma (C’) between
0~255.
- The part exceeding the set value is displayed
by red in Waveform and by blinking on the
screen.
●Y Picture Blink
- Sets if the part of a picture can be blinking
when Luma is out of set value at Y MAX, Y
MIN.
●C Picture Blink
- Sets if the part of a picture can be blinking
when color components of video input is out
of set value at C MAX, C MIN.

36 Multi Format LCD Monitor Multi Format LCD Monitor 37
[6] AUDIO [6] AUDIO (LVM-170A)
5. Menu Operations 5. Menu Operations
●Volume
- This item controls the embedded audio
output volume for the internal speakers and
[AUDIO OUT] on the back of the monitor
- Available values are between 0~30.
●Em. Audio Left/Right
- The item controls embedded audio channel
for left/right audio out of internal speaker
and [AUDIO OUT] in the back of the monitor.
- Available values are O, CH 1~CH 16, Ext.
Audio with SDI input, and Left : CH1, Right :
CH2 with HDMI input.
●Level Meter
- Used to control the audio level meter.
- Available modes are OFF, 16CH(HOR.),
16CH(VER.), 8CH, 8CH Side, 4CH and 4CH
Side with SDI input, and OFF, 2CH(Hor.),
2CH(Ver.) with HDMI input.
*16CH(HOR.) : It is displayed horizontally 8CH
on the top-left, and the other 8CH on the
top-right of the screen.
*16CH(VER.) : It is displayed vertically 8CH
on the center-left, and the other 8CH on the
center-right of the screen.
*8CH : It is displayed horizontally 4CH on the
top-left, and the other 4CH on the top-right
of the screen.
*8CH Side : It is displayed horizontally 8CH on
the top-right.
*4CH : It is displayed horizontally 2CH on the
top-left, and the other 2CH on the top-right
of the screen.
*4CH Side : It is displayed horizontally 4CH on
the top-right.
●Below menus are available for the LVM-
170A only.
●Loudness display
- Used to control the display method of the
Loudness.
- The mode will be changed as the following
sequence : [O]-[Bar]-[Log]-[Bar+Log]-[Loud
mode]-[O].
●Loudness channel
- Used to select the channel between [Stereo]
and [5.1Ch].
- When the channel is Stereo, the selected
channels for the Em.Audio Left/right are
applied to the Loudness meter.
- When the channel is 5.1Ch, 1/2/3/4/5
Channels are applied to the Left/right/
center/rear left/rear right.
●Loudness unit
- Used to change the display method of the
number and unit by standards.
- The mode will be changed as the following
sequence : [ITU(LKFS)]-[ATSC(-24)]-[EBU(-23]
- When the standard is ITU, the unit is same as
original dB and the LKFS range is from +6 to
-60. (ITU-R BS.1770-3)
- When the standard is ATSC, -24dB is 0 and
the LKFS range is from +30 to -36.(ATSC A/85)
- When the standard is EBU, -23dB is 0 and the
LU range is from +29 to -37 LU. (EBU R 128)
●Loudness log time
- Used to set the log time.
- Activates in the order : [8 Minute]-[16
Minute]-[32 Minute]-[1 Hour]-[2 Hour]-[4
Hour]-[8 Hour]-[24 Hour].
- Sets the time period of the Loudness log.
- In the case of 8 Minute, the log is divided
into 4 columns and each column
corresponds to 2 minutes.
- Last log on the right is used for monitoring
and corresponds to 4 seconds.
●Loudness transparency
- Used to activate the Transparent/ Opaque.
- Available modes are [Opaque] and [Blend].
●Loudness pause & start
- Used to start/ pause the Loudness meter.
- If there is no video signal, the Loudness
meter pauses automatically.
●Loudness reset
- Used to reset the values of the Loudness
meter.
●Level Meter Group
- Used to set the level meter group.
- Available modes are as below.
* 8CH/8CH Side : [G1+G2]-[G2+G3]-[G3+G4]-
[G1+G3]-[G1+G4]-[G2+G4]
* 4CH/4CH Side : [G1]-[G2]-[G3]-[G4]
●Level Meter Display (SDI Only)
- The item controls display method of audio
level meter
- Available modes are PAIR and GROUP.
●Level Meter Reference
- The item sets audio level default.
- Available values are -18dB and -20dB.
- Audio within selected value is displayed in
green and exceeded audio level is displayed
in yellow. Audio exceeding -4dB is displayed
in red.
●Level Meter Size
- The item controls the size of the audio level
meters.
- Available modes are NORMAL and LARGE.
●Peak Decay Time
- The item sets decrease time of audio level
meter top area.
- Available value is 0~100. The bigger value is,
the longer decrease time is.

38 Multi Format LCD Monitor Multi Format LCD Monitor 39
[7] DISPLAY & SET
5. Menu Operations
●System Default
- User can use SET DEFAULT menu to initialize
the values of BRIGHT, CONTRAST, CHROMA,
PHASE and APERTURE of the monitor.
●User cong set
- The item saves 3 user congurations.
- Available mode is USER1, USER2, USER3.
- Eective item is MARKER, CENTER MARKER,
SAFETY AREA, MARKER MAT,
MARKER COLOR in MARKER 1/2 and BRIGHT,
CONTRAST CHROMA, PHASE APERTURE in
PICTURE 1/3.
●OSD position
- The item sets OSD menu position.
- Available setting is CENTER, R-T, R-B, L-B, L-T.
- R-B and L-B are not available when
WAVEFORM/VECTOR is set.
●Key LED
- The item turns on / o LED in front of the
monitor.
- Even though you turn o KEY LED, when you
press LED button in front of the monitor, the
LED is on and after 5 sec. the LED is o.
●Firmware Version
- The item shows current rmware version.
●Serial Number
- The item shows serial number.
[7] DISPLAY & SET
5. Menu Operations
●Internal Pattern
- The items displays internal Gray/
ColorBar+Pluge pattern.
- Gray pattern range is 0%~100% and is set by
every 5%.
●3G Format
- You can select 3G FORMAT such as (NORMAL
MODE(AUTO - A 422 10BIT_YCbCr 50/60P),
A 444 10/12BIT_YCbCr, A 444 10/12BIT_RGB,A
422 12BIT_YCbCr, B 444 10/12BIT_ YCbCr, B
444 10/12BIT_RGB, B 422 12BIT_YCbCr, B 422
10BIT_YCbCr 50/60P) in order to support 3G
SDI A/B.
- It detects the signal automatically in
NORMAL MODE, when there is Payload
signal.
●Back Light
- The item shows current backlight value.
- When you Set Default, it returns to original
value.(Factory shipment.)
Available value is 0~100.
●Closed Caption
- The item controls closed caption.
- Available modes are OFF, 708, 608(LINE21)
and 608(ANC).
* 608 : CEA-608-B, 708 : CEA-708-C standards
display only.
●TimeCode Enable
- The item sets timecode.
- Available modes are OFF, VITC and LTC.
●Focus Assist
- The item makes you check which point your
camera’s focus is on easily by showing a
color on focused area.
- Available value changes in order of [(Mono)
On], [(Color) On] and [O].
* (Mono) On : Shows edge of focused area in a
designated color and the other area in black
& white applying Luma (Y’).
* (Color) On : Shows edge of only focused area
in a designated color.
●Focus Assist Color
- The item selects the color of FOCUS ASSIST.
- Available values are red, green and blue.
●Focus Assist Level
- The item controls focus assist level.
- Available values are between 0~100. Larger
value means greater detail detection.
- Focus assist color is presented when the
dierence between the border selections
exceeds the selected value.
- The feature is only available when FOCUS
ASSIST mode is selected. FOCUS
ASSIST mode can be selected by pressing
[BLUE ONLY/MONO] button.