Versa Desk PowerLift PLCSD User manual

REV. 05052021
PowerLift Corner Standing Desk
PLCSD
®
1 [phone]
[email protected]
American Manufacturing Lifetime Warranty
Protected by US Patent No. 10,485,336 & 10,849,424
VERSA DESK ®
Assembly Instructions
VERSA DESK ®

1 [phone]
[email protected]
American Manufacturing Lifetime Warranty
Protected by US Patent No. 10,485,336 & 10,849,424
VERSA DESK ®
Assembly Instructions
VERSA DESK ®
Phillips head screwdriver and/or
hand drill
4mm Allen wrench
(included)
Tape measure
Tools
Parts
Hardware
Leg Foot Side bracket
4-Piece Desktop
x3 x3 x2
Power cordM5x20 Wood Screw
x18
M6x14 Machine screw
DIN6 cableCable clipM5x16 Wood Screw
1/4-20 Phillips Bolt
x28
M6x10 Machine screw
x10
x20x35
x2
x1
x2
Top frame + control box
ControllerS BracketL Bracket Bluetooth App Box Power Strip Link Bracket x4
Front Bracket
3rd Leg Extension

1 [phone]
[email protected]
American Manufacturing Lifetime Warranty
Protected by US Patent No. 10,485,336 & 10,849,424
VERSA DESK ®
Assembly Instructions
VERSA DESK ®
M6x14 Machine screw
Slide control box (D) off the frame. Fully separate end frames
(A+C), you will find the center rails (B) inside.
NOTE: End frame C is placed on the side of the desk you plan to mount the control box and controller.
We recommend using the right side.
Place leg into one of the end frames ensuring
brackets are towards the top.
Align holes on leg with holes on end frame and insert
four (4) M6x10 machine screws through the holes in
the end frame and into the leg. Using the supplied
Allen wrench, rotate each screw just a few times.
After all four screws are inserted, tighten all.
Repeat this step for the other pairs of leg and frame.
Slide the side bracket into the end frame.
Insert two (2) M6x14 Machine screws through the
hole on the bottom of the end frame and into the
side bracket. Using the supplied Allen wrench,
rotate each screw just a few times.
After both screws are inserted, tighten both.
Repeat this step for the second leg/frame assembly.
Step 1
Step 2
Step 3
x2
M6x10 Machine screw
x4
BA C
D

1 [phone]
[email protected]
American Manufacturing Lifetime Warranty
Protected by US Patent No. 10,485,336 & 10,849,424
VERSA DESK ®
Assembly Instructions
VERSA DESK ®
Attach end frame with L-bracket (A) to end
frame with threaded-inserts (B) using (4)
M6x10 machine screws.
Place desktop with pre-drilled holes and
pre-installed inserts facing up. (We
reccomend placing them on cardboard,
blanket, rug, etc. to protect surface)
Adjust the width of the desk base by
sliding the two end frames outward.
Align the holes on the desk base and
the underside of the desktop.
Attach the desk base to desktop with
eight (8) 1/4-20 Phillips Bolts for the side
bracket holes going into the inserts. Use
four (4) M5x20 Wood Screws for the end
frame holes going into the desktop.
Step 4
Step 6
Step 5
M5x20 Wood Screw
x4
1/4-20 Phillips Bolt
x8
B
A
NOTE: DO NOT tighten all the way yet.
M6x10 Machine screw
x4
Slide the two center rails into the two end frames ensuring:
a) Center rail slots face inward
b) Center rail slots are closer to the top edge
when the assembly is upside down
(as shown in inset)

1 [phone]
[email protected]
American Manufacturing Lifetime Warranty
Protected by US Patent No. 10,485,336 & 10,849,424
VERSA DESK ®
Assembly Instructions
VERSA DESK ®
Lock the position of the
center rails using ten (10)
M6x10 machine screws,
ensuring the screws come in
contact with the center rails
by sliding them as needed.
Step 8
M6x10 Machine
screw
x10
Step 7
Ensure there is no gap between surfaces and that the corners of all surfaces allign with
each other by adjusting the end frame with L-bracket (Fig. A)
Tighten the (4) M6x10 machine screws (Fig A.) going through end frame with L-bracket
from Step 4 all the way.
Then, attach (4) link brackets using (6) M5x20 Wood Screws for each bracket.
fig. A
Tighten x4 M6x10 Machine screw
M5x20 Wood Screw
x24

1 [phone]
[email protected]
American Manufacturing Lifetime Warranty
Protected by US Patent No. 10,485,336 & 10,849,424
VERSA DESK ®
Assembly Instructions
VERSA DESK ®
For each leg, attach a foot with four (4) M6x14
Machine screws and tighten in a cross pattern.
M6x14 Machine screw
x4
Locate pre-drilled holes toward the front
of the desktop. You can use the set of
holes on either side, but we recommend
using the right side.
Using two (2) M5x16 Wood Screws,
attach the controller to the desktop.
Step 10
M5x16 Wood Screw
x2
Step 11
Slide the control box back onto
the corner end frame. There
are two placement options, we
suggest placing it on the side
closest to your controller.
Step 9

1 [phone]
[email protected]
American Manufacturing Lifetime Warranty
Protected by US Patent No. 10,485,336 & 10,849,424
VERSA DESK ®
Assembly Instructions
VERSA DESK ®
Step 12
Using the adhesive back, stick the Power Strip (PS) and BlueTooth App Box (BT) onto the
underside of the desktop as shown below.
Connect cable exiting Leg (closest to control box) directly into the control box (CB). (M1 - red)
Connect 2 DIN6 cables to the other 2 leg cables and then to the control box. (M2&M3 - red+blue)
Connect controller cable and control box to the BlueTooth App Box. (HS - orange)
Connect the power cord to the control box and power strip,
as well as the BlueTooth App Box’s power cord to the power strip. (AC - green)
M1 M2 M3
AC
HS
to outlet
BT
CB
PS
Using the adhesive-back cable clips, secure the cables so they do not sag.
With at least two people, grab the DESK BASE (NOT the desktop) and turn right-side up.
Adjust pre-installed glides on the feet as needed.
Step 13

1 [phone]
[email protected]
American Manufacturing Lifetime Warranty
Protected by US Patent No. 10,485,336 & 10,849,424
VERSA DESK ®
Assembly Instructions
VERSA DESK ®
Step 14
Attach L extension bracket with two (2) M6x14 Machine screws.
Step 15
Attach S extension bracket with two (2) M6x10 Machine screws.
x2
M6x14 Machine screw
M6x10 Machine screw
x2

1 [phone]
[email protected]
American Manufacturing Lifetime Warranty
Protected by US Patent No. 10,485,336 & 10,849,424
VERSA DESK ®
Assembly Instructions
VERSA DESK ®
Step 16
Slide Front Bracket into place, align the holes with the inserts on the underside of the
desktop and attach with three (3) 1/4-20 Phillips Bolts.
Step 17
Place 4th Surface onto the brackets, align the holes of the Front Bracket woth the
inserts on the underside of the surface and attach with three (3) 1/4-20 Phillips Bolts.
1/4-20 Phillips Bolt
x3
1/4-20 Phillips Bolt
x3

1 [phone]
[email protected]
American Manufacturing Lifetime Warranty
Protected by US Patent No. 10,485,336 & 10,849,424
VERSA DESK ®
Assembly Instructions
VERSA DESK ®
Step 18
Secure the surface with six (6) Wood Screws going through the two brackets.
x4
1/4-20 Phillips Bolt

1 [phone]
[email protected]
American Manufacturing Lifetime Warranty
Protected by US Patent No. 10,485,336 & 10,849,424
VERSA DESK ®
Assembly Instructions
VERSA DESK ®
1/4-20 Phillips Bolt
x4
Tools
Add-on: Sit to Stand Keyboard Arm and Tray
Parts
Assembly
Phillips head screw-
driver and/or hand drill 1/4-20 Phillips BoltKeyboard Tray Brackets
Desk
x8x2
1/4-20 Phillips Bolt
x4
Locate the four pre-installed inserts and align
them with the holes in the brackets of the
keyboard tray assembly.
Using four (4) 1/4-20 Phillips Bolts, attach the
Keyboard tray to the underside of the desktop.
Attach two (2) brackets to the keyboard tray
assembly using four (4) 1/4-20 Phillips Bolts.
Step 1
Step 2

1 [phone]
[email protected]
American Manufacturing Lifetime Warranty
Protected by US Patent No. 10,485,336 & 10,849,424
VERSA DESK ®
Assembly Instructions
VERSA DESK ®
Tools
Add-on: CPU holder
Parts
Assembly
Phillips head driver
and/or hand drill 1/4-20 Phillips BoltCPU Holder Brackets
x8x2
Lock Pin
x2
1/4-20 Phillips Bolt
x4
1/4-20 Phillips Bolt
x4
Using four (4) 1/4-20 Phillips Bolts,
attach the slide bracket onto the two
brackets from the previous step.
Attach the two (2) brackets to underside
of the desktop with four (4) 1/4-20
Phillips Bolts, on the side of the desk
you would like the CPU holder to be on.
Step 1
Step 2
Slide Bracket

1 [phone]
[email protected]
American Manufacturing Lifetime Warranty
Protected by US Patent No. 10,485,336 & 10,849,424
VERSA DESK ®
Assembly Instructions
VERSA DESK ®
Add-on: CPU holder
Assembly
Slide the CPU holder into the Slide Bracket.
Be sure that the Carriage Screws are facing
the Inside of the CPU Holder and the Thumb
Nuts and Washers are facing Outside.
Use the Thumb Nuts to adjust the CPU
Holder to the desired size.
Step 3
Step 4
Pass the lock pins through
the Slide Bracket holes.
Step 5
Carriage Screw
Washer
Thumb Nut

1 [phone]
[email protected]
American Manufacturing Lifetime Warranty
Protected by US Patent No. 10,485,336 & 10,849,424
VERSA DESK ®
Assembly Instructions
VERSA DESK ®
Use
Trouble Shooting
If your desk is not functioning properly it may need to be reset. Unplug the power cord for 20
seconds. Plug the power cord back in and follow the RESET procedure outlined above.
If your desk’s contoller LED readout displays an error code “Er1 - Er13” or “ASR”, confirm that all
wired connections are secure, then perform the reset procedure above.
If the error message persists after the reset procedure contact Versa Tables.
If the height difference between the legs exceeds 1.5 inches, stop the reset procedure and con-
tact Versa Tables immediatly.
If the controller displays “HOT”, allow the components to cool down for 20 minutes.
Reset Procedure: Press and hold DOWN button on controller until desk reaches its lowest
height. Release DOWN button. Press and hold DOWN button again until LED displays “ASR”.
Release DOWN button. Press and hold DOWN button again until desk slightly lowers, rises and
stops. Release DOWN button.Your desk is now ready to use!
Adjusting Desk Height: The desk base can be adjusted by pressing and holding either the UP or
DOWN button until the desired height is reached.
Creating Height Presets: The desk’s controller is programmable for up to four presets. To create
a preset, use the UP and DOWN buttons to find a desired height, then
press the ‘S’ button followed by Preset buttons 1 through 4.
CAUTION: Once a preset button is pushed, the desk will move to the programmed height.
IMPORTANT: You must RESET the desk prior to use.
Make sure no obstacles are in the desk’s path and the desktop is away from walls.
Make sure all cables are the appropriate length to accomodate the change in height.
!

1 [phone]
[email protected]
American Manufacturing Lifetime Warranty
Protected by US Patent No. 10,485,336 & 10,849,424
VERSA DESK ®
Assembly Instructions
VERSA DESK ®
Press the DOWN button until the desk reaches the lowest position.
Measure the height from the floor to the top surface of the desktop.
If the displayed height does not match your measurement, follow these steps:
Press the DOWN button until display flashes “ASR”.
Press the “S” button until the numeric display begins flashing.
Use the UP/DOWN buttons to set the value so that it matches your measured height.
Once display changes back to “ASR”, press DOWN button until the desktop lowers and rises
slightly.
The desk is designed to go to its minimum and maximum height limits, allowing for the widest
possible range. If you prefer a narrower range, follow these steps to adjust the upper and lower
limits:
To Set a new maximum desk height:
Press the UP or DOWN button to move the desk to the desired maximum height.
Press the “S” button once, and then the UP button once. The Display will flash “S-”
Press and hold the “S” button until the Display shows “999”, and then changes to numeric value of
new upper limit.
To Set a new minimum desk height:
Press the UP or DOWN button to move the desk to the desired minimum height.
Press the “S” button once, and then the DOWN button once. The Display will flash “S-”
Press and hold the “S” button until the Display shows “000” and then changes to numeric value of
new lower limit.
Removing adjusted maximum and minimum heights:
Press and hold the “S” button until the display flashes “S-”.
Within 5 seconds, press the “S” button again and hold for 2 seconds. The display will change to
“555” and return to the current numeric height setting. Limits are now removed.
Note: If memory settings were previously set outside of the new minimum and maximum height
settings, they will default to the new minimum and maximum settings. To set new minimum and
maximum height settings outside of the current settings, you will need to first remove the current
minimum and maximum settings.
Calibrating the Height
Technical Specifications
Setting the Upper/Lower Limits
Height Range
Base Width
Travel Speed
Weight Capacity
Duty Cycle
23.5” - 49” (excluding desktop)
42” min. - 74” max
1.5” per second (no load)
1000N
10%. Max. 2 mins on, 18 mins off
Soft start / stop
Adjustable Leveling Studs
4 Memory presets

1 [phone]
[email protected]
American Manufacturing Lifetime Warranty
Protected by US Patent No. 10,485,336 & 10,849,424
VERSA DESK ®
Assembly Instructions
VERSA DESK ®
Press the DOWN button until the desk reaches the lowest position.
Press the DOWN button again until display flashes “ASR”.
Press and hold the “2” button until display shows “10.3” (centimeters) or “10.4” (inches).
Press and hold the “2” button again until desired setting is reached. Once the chosen setting is
displayed, release the button and wait about 5 seconds for the display to return to “ASR”.
Press the DOWN button until the desktop lowers slightly, then rises slightly and the display
changes back to the numeric height setting.
The keypad can be locked to prevent accidental activation or movement of the desk.
To lock: Press and hold “S” button until display changes to “LOC”
To unlock: Press and hold “S” button until display changes to numeric height setting.
NOTE: If a power outage occurs, the program will automatically return to the unlocked setting.
The desk has an Anti-Collision Sensitivity that will stop the desk’s movement if it hits something
on the way down or up. You can change this Sensitivity level by doing the following:
Press the DOWN button until the desk reaches the lowest position.
Press the DOWN button until display flashes “ASR”.
Press and hold the UP button until display shows “10.5”, “10.6”, or “10.7”
“10.5” = 10 kg pressure (22 lbs) (most sensitive)
“10.6” = 15 kg pressure (33 lbs)
“10.7” = 20 kg pressure (44 lbs) (least sensitive)
Press and hold the UP button again until desired setting is reached. Once the chosen setting is
displayed, release the button and wait about 5 seconds for the display to return to “ASR”.
Press the DOWN button until the desktop lowers slightly, then rises slightly and the display
changes back to the numeric height setting.
Controller Lock
Changing Units
Anti-Collision Sensitivity
These steps allow the desktop to be set to either One-Touch or Constant-Touch. One-Touch
requires only a single touch of the “1, 2, 3, or 4” buttons to move the desktop to a preset
memory location. OneTouch is the default setting. Constant-Touch requires a continuous touch
of the “1, 2, 3, or 4” button to move the desktop to a preset memory location.
To change between One-Touch and Constant-Touch:
Press the DOWN button until the desk reaches the lowest position.
Press the DOWN button again until display flashes “ASR”.
Press and hold the “1” button until display shows “10.1” (One-Touch) or “10.2” (Constant-Touch)
Press the “1” button again until desired setting is reached. Once the chosen setting is displayed,
release the button and wait about 5 seconds for the display to return to “ASR”.
Press the DOWN button until the desktop lowers slightly, then rises slightly and the display
changes back to the numeric height setting.
One-Touch/Constant-Touch