Vicon VC-621 User manual

VC-621 AND VC621C
ENVIRONMENTAL HOUSING CAMER
A
About this manual
Dimensions : inch (mm)
INSTRUCTION MANUAL XX167-10
Before installing and using the camera, please read this manual
carefully. Be sure to keep it handy for later reference.
TROUBLESHOOTING
Before sending the camera out for repair, check the items
below. If the problem persists after checking these items,
contact your service center.
■If no image appears
Is the coaxial cable attached securely?
Are the power and voltage normal?
Has the iris of the lens inside the camera been
adjusted correctly (with the level volume) ?
Is there adequate illumination?
■If the image is unclear
Is the lens in focus?
Is the lens dirty?
Dirt or fingerprints on the lens can adversely affect the
images. Gently wipe any dirt or fingerprints off the lens
with a soft cloth or lens cleaning paper and cleaning
fluid (commercially available).
Is the monitor adjusted correctly?
■Do not open or modify
Do not open the case except during maintenance and
installation, as it may be dangerous and cause damage.
■Do not put objects inside the unit
Make sure that no metal objects or flammable
substances get inside the camera. It could cause fire,
short-circuits or damage.
■Be careful when handling the unit
To prevent damage, do not drop the camera or subject
it to strong shock or vibration.
■Install away from electric or magnetic fields.
■Protect from humidity and dust.
■Protect from high temperature
Be careful when installing close to the ceiling , in a
kitchen or boiler room, as the temperature may raise to
high levels.
■Cleaning
Dirt can be removed from the case only by wiping it
with a soft cloth moistened with a soft detergent solution
.
■Mounting Surface
The mounting surface material must be strong enough to
PRECAUTIONS
SPECIFICATION
GENERAL Spec NTSC PAL
CCD Type 1/3" 410K Pixels Color 1/3" 470K Pixels Color
Total Number of Pixels 811(H) x 508(V) 795(H) x 596(V)
Light Sensitivity
Video Output 10Vp-p/75ohm Composite
Resolution 550TV Lines
S/N Ratio 48dB or more (AGC off)
Shutter Speed 1/60s - 1/100,000s 1/50s - 1/100,000s
Sync System Internal / External (Line Lock)
White Balance DIP Switch Select (AWB / ATWV)
Connector
Power Input Power leads
BNC Cable
Electrical Spec
Voltage DC12V(11-20V) or AC24V(20 - 27V)
Power Consumption DC12V : LED (ON:7.5W OFF:2.5W)
AC24V : LED (ON:7.1W OFF:2.1W)
Mechanical Spec
Lens 5-50mm
Dimension 98.0 x 291.5mm
Weight 1.7kg
Operation Temp -10˚C ~ +55˚C
In Storage Temp -20˚C ~ +70˚C
Operation Humidity Under 90% (Non-condensing)
COLOR - 0.028fc (0.3lux)
BW - 0.009fc (0.1 lux)

■CAMERA SETTINGS
①DIP Switch Functions
(1) Compensating for backlight (2) Confirming the iris setting
ON When back light is too bright AE (Off) When fixed iris lens is installed
OFF Normal setting ME (On) When DC autoiris lens is installed
CAUTION : It will be correctly set by adjusting DC lens control. CAUTION : The iris setting is preadjusted as the best condition for
use at time of factory shipment, so it isn't necessary to change settings
(3) Confirming the white balance (4) Setting gain control (AGC)
For adjusting the sensitivity of the camera. Use this setting for shooting
in dark environments.
ON Normal setting
OFF Set this when there is excessive noise
②Second Video Out Connector (Option) ⑤Adjusting Level Volume
If installer do setting with protable monitor, this connector is If the entire image is too dark or bright, or the backlight
connected. compensation is not correct even after ①is set to "ON",
you need to adjust the level volume.
③IR LED Connector (Option) CCW (Low) Closes the lens iris, making the entire image darker
If extra IR LED board is attached, this connector is used. CW(High) Opens the lens iris, making the entire image brighter
④Setting Monitor Synchronization ⑥DC Varifocal Connector
(24VAC adaptor users) This should be used with ⑤DC IRIS LENS.
Vertical sync disturbance may occur when a selector is used to
switch between multiple cameras connected to one monitor.
To prevent vertical sync disturbance, adjust ④.⑦Power Connector
CAUTION Connect with AC/DC power board attached inside.
* When using the DC 12V adaptor, sync setting is set to internal sync.
ATW Use this under light source below 2500K and over
9500K of natrium.
AWB Use this under light source between 2500K and 9500K of
fluorescent lamps, incandescent light
CAMERA SETTINGS
①
①
Portable
Monitor
②
③
④
⑤
⑥
DC
⑦

■CAMERA CONNECTIONS
■CAMERA FOCUS SETTING ■CAMERA ANGLE SETTING
■AUTOIRIS LEVEL ADJUSTMENT
INSTALLATION
CAUTION :
Check for polarity when using a DC 12V power supply.
※ATTENTION
1. Do not rotate ①more than 360˚
2. Do not twist
②
more turns than necessar
y
.
※ADJUSTMENT
1. Separate opening cap ①from camera body.
2. By using screw driver ②"-" or "+", adjust IRIS level.
3. Assemble opening cap ①with camera body.
①②
①
②

Brussels Office
Planet II - Unit E
Leuvensesteenweg 542
B-1930 Zaventem
Belgium
[phone]
Fax: [phone]
Far East Office
Unit 5, 17/F, Metropole Square
2 On Yiu Street, Shatin
New Territories,
Hong Kong
(852) 2145-7118
Fax: [phone]
Internet Address: www.vicon-cctv.com
Vicon Industries Inc.
Corporate Headquarters
89 Arkay Drive
Hauppauge, New York 11788
USA
631-952-CCTV (2288) 800-645-9116
Fax: 631-951-CCTV (2288)
European Headquarters
Brunel Way
Fareham, PO15 5TX
United Kingdom
[phone]
Fax: [phone]
Vicon Part number 8009-8168-00-00 Rev705