Viper 350 plus User manual

NOTE: This product is intended for installation by a professional

installer only! Any attempt to install this product by any person other

than a trained professional may result in severe damage to a vehicle’s

electrical system and components.

350 Plus

Installation Guide

N3105V- 2008-12

Bitwriter™, Code Hopping™, DEI®, Doubleguard®, ESP™,

FailSafe®, Ghost Switch™, Learn Routine™, Nite-Lite®, Nuisance

Prevention® Circuitry, NPC®, Revenger®, Silent Mode™, Soft

Chirp®, Stinger®, Valet®, Vehicle Recovery System®, VRS®, and

Warn Away® are all Trademarks or Registered Trademarks of Directed

Electronics, Inc.

The Bitwriter®(p/n 998T)

requires chip version 2.4 or

newer to program this unit.

Contents

Primary Harness (H1) Wire Connection Guide.............................................................. 4

Primary Harness Wiring Diagram.............................................................................. 4

Primary Harness Wiring Instructions......................................................................... 4

Door Lock Harness (H2), 3-PIN Connector ................................................................ 11

Plug-In LED and valet/program switch......................................................................... 12

Programmer Interface, 3-Pin BLACK Plug.............................................................. 13

Mounting the Control Center ................................................................................. 13

On-Board Dual-Stage Shock Sensor ............................................................................. 14

Optional Sensor Harness, 4-pin Connector .................................................................. 15

Programming Jumper.................................................................................................... 16

Light Flash Jumper .................................................................................................. 16

Bypassing Sensor Inputs................................................................................................ 17

System Features Learn Routine ..................................................................................... 18

System Features Menus................................................................................................. 21

Menu #1 - Basic Features......................................................................................... 21

Menu #2 - Advanced Features ................................................................................. 22

Feature Descriptions ..................................................................................................... 22

Menu #1 - Basic Features......................................................................................... 22

Menu #2 - Advanced Features ................................................................................. 24

Transmitter/Receiver Learn Routine ............................................................................. 27

Transmitter Configurations........................................................................................... 30

Standard Configuration .......................................................................................... 30

Three-button configuration - Optional not included............................................... 30

Diagnostics.................................................................................................................... 31

Arm/Disarm Diagnostics ......................................................................................... 31

System Status Chirps ............................................................................................... 31

Table of Zones......................................................................................................... 32

Long Term Event History............................................................................................. 32

Multi-Level Security Arming......................................................................................... 33

Optional Vehicle Recovery System (VRS)..................................................................... 34

Nuisance Prevention® Circuitry................................................................................... 34

Rapid Resume Logic ..................................................................................................... 34

Troubleshooting............................................................................................................ 35

Primary Harness (H1) Wire Connection

Guide

Primary Harness Wiring Diagram

H1/1

H1/2

H1/3

H1/4

H1/5

H1/6

H1/7

H1/8

H1/9

H1/10

H1/11

H1/12

___

ORANGE (-) 500 mA Armed Output

___

WHITE (+)/(-) Selectable Light Flash Output

___

WHITE/BLUE (-) 200 mA Channel 3 Programmable Output

___

BLACK/WHITE (-) 200 mA Domelight Supervision Output

___

GREEN (-) Door Trigger Input, Zone 3

___

BLUE (-) Instant Trigger Input, Zone 1

___

VIOLET (+) Door Trigger Input, Zone 3

___

BLACK (-) Chassis Ground Input

___

YELLOW (+) Switched Ignition Input, Zone 5

___

BROWN (+) Siren Output

___

RED (+) Constant Power Input

___

RED/WHITE (-) 200 mA Channel 2 Output

Primary Harness Wiring Instructions

This guide describes in detail the connection of each wire. Also included are

possible applications of each wire. This system was designed with the ultimate

in flexibility and security in mind. Many of the wires have more than one

possible function. Please read carefully to ensure a thorough understanding

of this unit.

H1/1 ORANGE (-) ground-when-armed output

This wire supplies a (-) ground as long as the system is armed. This output

ceases as soon as the system is disarmed. The orange wire is pre-wired to control

the 8618 starter kill relay. It can supply up to 500 mA of current.

NOTE: If using the H1/1 Orange wire to activate an add-on accessory such

as window automation, or voice module a 1Amp diode must be installed to

ensure proper operation. Insert the diode as shown in the following diagram.

IMPORTANT! Never interrupt any wire other than the starter

wire.

H1/2 WHITE (+/-) light flash output

As shipped, the H1/2 WHITE wire should be connected to the (+) parking

light wire. If the light flash polarity jumper is moved to the (-) position (see the

Programming Jumper section of this installation guide), this wire supplies

a (-) 200 mA output.

NOTE: For parking light systems that draw 10 amps or more, the jumper

must be switched to a (-) light flash output (see the Programming Jumpers

section of this guide). P/N 8617 or a standard automotive SPDT relay must

be used on the H1/2 light flash output wire.

IMPORTANT! DO NOT connect this wire to a negative vehicle

light flash wire before changing the programming jumper to

the negative polarity position or damage to vehicle light circuit

may occur.

H1/3 WHITE/BLUE 200 mA (-) channel 3 output

This wire provides a (-) 200 mA output whenever the transmitter button(s)

controlling channel three is pressed. This output can be programmed to

provide the following types of output (see System Features Learn Routine

section of this guide):

A validity output will send a signal as long as the transmission is•

received.

A latched output will send a signal continuously when the channel•

three button(s) is pressed and released. The signal will continue

until channel three is pressed again.

A latched/reset with ignition output works similar to the latched•

output, but will also reset (output will stop) when the ignition is

turned on and then off.

A 30 second timed output will send a signal for 30 seconds when•

channel three is pressed. This output can be shut off during the

30-second period by pressing Channel 3 again.

This output can also be programmed to provide a second unlock•

pulse when the unlock button is pressed a second time after

disarming the system. This can be used to unlock the passenger

doors when installing progressive door locks.

IMPORTANT! Never use this wire to drive anything but a

relay or a low-current input! This transistorized output can

only supply 200 mA, and connecting directly to a solenoid,

motor, or other high-current device will cause the module to

fail.

H1/4 BLACK/WHITE (-) 200 mA domelight supervision output

Connect the H1/4 wire to the optional domelight supervision relay as shown

in the following diagram:

IMPORTANT! This output is only intended to drive a relay. It cannot be connected

directly to the domelight circuit, as the output cannot support the current draw of one

or more bulbs.

H1/5 GREEN (-) door trigger input

Most vehicles use negative door trigger circuits. Connect the green wire to a

wire showing ground when any door is opened. When connecting to newer

model vehicles there is generally a need to use individual door triggers. See

DirectFax document 1076 for wiring instructions. This wire will report Zone

NOTE: If using a door trigger wire that has a delay, Advanced Menu 2, feature

6 or the 998T Bitwriter can be used to turn Bypass Notification off.

H1/6 BLUE (-) instant trigger input

This input will respond to a negative input with an instant trigger. It is ideal for

hood and trunk pins and will report on Zone 1. It can also be used with Directed

single-stage sensors. The H1/6 blue instant trigger wire can also be used to shunt

sensors during operation of auxiliary channels or remote start. (See Bypassing

Sensor Inputs section of this guide.)

H1/7 VIOLET (+) door trigger input

This type of dome circuit is used in many Ford products. Connect the violet

wire to a wire that shows (+)12V when any door is opened. This wire will report

Zone 3.

NOTE: If using a door trigger wire that has a delay, Advanced Menu 2, feature

6 or the 998T Bitwriter can be used to turn Bypass Notification off.

H1/8 BLACK (-) chassis ground connection

Connect this wire to a clean, paint-free sheet metal location (driver kick

panel) using a factory bolt that DOES NOT have any vehicle component

grounds attached to it. A screw should only be used when in conjunction with

a two-sided lock washer. Under dash brackets and door sheet metal are not

acceptable ground points. It is recommended that all security components be

grounded at the same location.

H1/9 YELLOW (+) ignition input

Connect this wire to the (+) 12 volts ignition wire. This wire is pre-wired to

the starter kill relay and must show (+) 12 volts with the key in RUN position

and during cranking. Take great care that this wire cannot be shorted to the

chassis at any point.

\\\\\\\

H1/10 BROWN (+) siren output

Connect this to the RED wire of the Revenger® siren. Connect the BLACK

wire of the siren to (-) chassis ground, preferably at the same point you connect

the control module’s BLACK ground wire.

H1/11 RED (+)12V constant power input

Before connecting this wire, remove the supplied fuse. Connect to the battery

positive terminal or the constant 12V supply to the ignition switch.

NOTE: Always use a fuse within 12 inches of the point you obtain (+)12V.

Do not use the 15 amp fuse in the harness for this purpose. This fuse protects

the module itself.

H1/12 RED/WHITE 200 mA (-) channel 2 output

When the system receives the code controlling channel 2 for longer than 1.5

seconds, the RED/WHITE will supply an output as long as the transmission

continues. This is often used to operate a trunk/hatch release or other relay/

driven function.

IMPORTANT! Never use this wire to drive anything but a relay

or a low-current input! The transistorized output can only supply

200 mA of current. Connecting directly to a solenoid, motor, or

other high-current device will cause it to fail

Door Lock Harness (H2), 3-PIN Connector

H2/A

H2/B

H2/C

___

Green (-) Lock, (+) Unlock Output

___

Empty Unless Using 451M

___

Blue (-) Unlock, (+) Lock Output

IMPORTANT! The door lock outputs are low current and should not

be attached directly to any high current device; they are only to be

used to activate relays.

For detailed instructions about connecting to the vehicle’s power door lock

systems, refer to the Door Lock Wiring guide (Document No. 1041) available

to authorized dealers only from the technical resources listed at the front of

this guide.

Plug-In LED and valet/program switch

The LED and the valet switch are incorporated into the Control Center. The

LED line plugs into the WHITE 2-pin port, and the valet switch plugs in to

the BLUE 2-pin port.

NOTE: The onboard LED can be substituted with an optional outboard

LED (P/N 8634 for Blue LED and 8633 for red LED). The LED fits into a

9/32 inch mounting hole. Be sure to check for clearance prior to drilling the

mounting hole.

You can also substitute an external valet switch for the Control Center valet

switch (P/N 8631 is a 5-pack of these switches)

Valet switch

LED

Important! With the Control Center more customers will want the Ghost

switch coded disarm feature - make sure to check with the customer.

Programmer Interface, 3-Pin BLACK Plug

The BLACK three-pin port connection is for programming the unit.

When using the 998T Bitwriter®, it is possible to configure any and

all of the programmable functions. For more information please refer

to the guide packaged with the programmer.

Mounting the Control Center

The control center’s position should be discussed with the vehicle owner prior

to installation, since it will be visible to to the vehicle’s operator.

The best location for the Control Center is centered high on either the front

or rear windshield. For optimal range, the antenna should be mounted verti-

cally. It can be mounted horizontally in relation to the windshield or under the

dashboard away from metal, but range will be diminished. Metallic window

tint can also affect range, so this should be a consideration when determining

the mounting location.

After determining the best mounting location, follow these steps:

1. Clean the mounting area with a quality glass cleaner or alcohol to remove

any dirt or residue.

2. Plug the Control Center cable into the Control Center.

3. Mount the Control Center using the supplied double-sided tape.

4. Route the Control Center cable to the control module and plug it into the

four-pin antenna connector.

Important! To achieve the best possible range, DO NOT leave the

control center cable bundled under the dash. Always extend the cable

full length during installation, regardless of the antenna mounting

location.

CONTROL CENTER CABLE

CONTROL

CENTER

On-Board Dual-Stage Shock Sensor

There is a dual-stage shock sensor inside the control unit. Adjustments are

made via the rotary control as indicated in the diagram. Since the shock sensor

does not work well when mounted firmly to metal, we do not recommend

screwing down the control module. The full trigger of the on-board shock

sensor reports Zone 2. (See Table of Zones section of this guide.)

Note: When adjusting the sensor, it must be in the same mounting location

that it will be after the installation is completed. Adjusting the sensor and then

relocating the module requires readjustment.

Optional Sensor Harness, 4-pin

Connector

The four-pin sensor harness is optional, and is not included with this unit.

RED (+) 12V Constant and BLACK (-) Ground:

These wires supply constant (+) 12 volts and ground to the optional sensor.

BLUE/GREEN (-) Multiplex Input:

These wires are multiplex inputs. If a (-) input of less than 0.8 seconds is

supplied to either wire, the Warn-Away response will occur. A (-) input of

longer than 0.8 seconds to either wire will initiate the triggered sequence and

report Zone 4.

Programming Jumper

Light Flash Jumper

This jumper is used to determine the light flash output. In the (+) position,

the on-board relay is enabled and the unit will output (+)12V on the WHITE

wire, H1/2. In the (-) position, the on-board relay is disabled. The WHITE

wire, H1/2, will supply a 200 mA (-) output suitable for driving factory

parking light relays.

NOTE: For parking light circuits that draw 10 amps or more, the jumper must

be switched to a (-) light flash output. P/N 8617 or a standard automotive

SPDT relay must be used on the H1/2 light flash output harness wire.

Important! DO NOT connect the H1/2 light flash wire to

a negative vehicle light flash wire before changing the

programming jumper to the negative polarity position or

damage to vehicle light circuit may occur.

Bypassing Sensor Inputs

There are times when you need to temporarily bypass all sensor inputs to

the unit, such as when remote starting the vehicle. Anytime an auxiliary

channel output is used, all inputs are bypassed for 5 seconds. During the 5

second bypass period, ground can be supplied to the H1/6 Blue wire without

triggering the unit.

When the 5 second bypass period ends, if the unit sees ground on the H1/6

Blue wire, all trigger inputs except the door trigger input will remain bypassed

until 5 seconds after ground is removed from the BLUE wire. The ignition

input needs to be bypassed during remote start also. This can be done using

the status and ignition output of a Directed Electronics remote engine starting

unit as shown in the following diagram:

Alarm system

(

-) During remote

start output

Starter kill

relay

Yellow ignition output

from DEI remote start

Yellow H1/9

ignition input

System Features Learn Routine

The System Features Learn Routine dictates how the unit operates. Due to

the number of steps, they have been broken up into two menus. It is possible

to access and change any of the feature settings using the Valet/Program

switch. However, this process can be greatly simplified by using the 998T

Bitwriter. Any of the settings can be changed and then assigned to a particular

transmitter, up to four, a feature called Owner Recognition. Each time that

particular transmitter is used to disarm the system, the assigned feature settings

will be recalled. Owner Recognition is only possible when programming the

unit via the 998T Bitwriter.

If the system was previously programmed using the 998T Bitwriter, the learn

routine may be locked. If the siren generates one long chirp when attempting

to program the unit, the learn routine is locked and must be unlocked using

the 998T Bitwriter.

1. Open a door. (The H1/5 GREEN wire or the H1/7

VIOLET wire must be

connected.)

2. Ignition. Turn the ignition on, then back off: (The

H1/9 YELLOW wire must be connected.)

3. Select a Menu. Press and HOLD the Valet/Program

switch: (The Valet/Program switch must be plugged

into the blue port.) After three seconds the siren will

chirp once indicating entry to the Basic Features Menu

#1. If this is the menu you wish to access, release the

button and go on to Step 4. If the button is not

released, you will jump to the Advanced Features Menu

#2 and the siren will chirp twice. Once you have

selected the desired menu, release the Valet/Program

button and then proceed to Step 4.

4. Select a Feature. Press and release the Valet/Program

switch the number of times corresponding to the feature

you wish to change. For example, to access the third

feature, press and release the switch three times. Then

press the switch once more and HOLD it. The siren

will chirp the number of times equal to the step you

have accessed.

5. Program the Feature. While holding the Valet/

Program switch, you can toggle the feature on and off

using the remote transmitter. Pressing



will select

the one chirp setting. Pressing



will

select the two chirp setting.

(See Systems Features menus)

NOTE: The Valet pulse count feature (2-5) and the

Channel three timed output (2-9) have five possible

settings each. Pressing



will toggle through all the

two-chirp settings.

6. Release the Valet/Program Switch.

Once a feature is programmed:•

Other features can be programmed within the same menu.•

Another menu can be selected.•

The learn routine can be exited if programming is complete.•

To access another feature in the same menu:

Press and release the Valet/Program switch the number of times necessary•

to advance from the feature you just programmed to the next one you

want to program.

Then press the Valet/Program switch once more and• HOLD it.

For example, if you just programmed the third feature in the menu and you

would like to program the seventh feature in the menu, you would press and

release the Valet/Program switch four times and then press it once more and

hold it. The siren would chirp seven times to confirm access to the seventh

feature.

To select another menu:

Press and hold the Valet/Program switch.•

After three seconds, the unit will advance to the next menu and the siren•

will chirp, indicating which menu has been accessed.

For instance, if you just programmed some features in Menu #1 (Basic Features)

and you wish to program a feature in Menu #2, you press and HOLD the

Valet/Program button. After three seconds, the siren chirps twice indicating

access to Menu #2.

To exit the learn routine do one of the following:

Close the open door.•

Turn the ignition on.•

No activity for longer than 15 seconds.•

Press the Valet/Program switch too many times.•

Table of contents

Other Viper Car Security manuals

Viper

Viper Hayward 5500 User manual

Viper 350 Plus User manual