Vivo STAND-V002 User manual

Single Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v001
[email protected]om www.vivo-us.com 1-800-371-5654
SKU: STAND-V001

2 3
ASSEMBLY STEPS
STEP 1
TOOLS NEEDED
22lbs
(9.98kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
Phillips
Screwdriver
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
PACKAGE CONTENTS
A (x1)
Pole
B(x1)
Clamp
C(x1)
Clamp Brace
N2 (x2)
Wire Clip
O(x1)
Allen Key Set
R(x4)
M4x30 Bolt
N1 (x1)
Wire Clip
J (x1)
Support Plate
K (x1)
M10 Washer
L (x1)
Spring Washer
M (x1)
Grommet
Base Plate
T1 (x1)
So Pad
S(x4)
M4 Spacer
D(x1)
Swivel Arm
E(x1)
VESA Plate
F (x3)
M5x14 Bolt
G(x2)
M8x12 Bolt
H (x1)
Nut
I (x1)
M10 Bolt
Q(x4)
M4x12 Thumb
Bolt
P(x1)
Wrench
T2 (x1)
Grommet Pad
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
a
c
f
Figure 1
t1
Figure 2
g
o
b
Plastic Knob Figure 3
Option A: Desk Clamp Install
1. Install the clamp brace (C) to the pole (A) using x3 M5x14 bolts (F). See Figure 1.
2. Attach so pad (T1) to the clamp brace (C) , see Figure 2.
3. Install the clamp (B) to the pole assembly according to the thickness of the desktop. The
thickness can be changed to 3 positions. Connect using x2 M8x12 bolts (G) and tighten using the
Allen key (O). Tighten the clamp to the desktop using the plastic knob. See Figure 3.
Option B: Grommet Base with Existing Hole
If existing grommet hole comes with a plastic
protector, remove it to ensure a flat surface
before installing the desk mount.
1. Install grommet base plate (M) to the pole
(A) using x3 M5x14 bolts (F). See Figure 4.
2. Attach so pad (T2) to the grommet base
plate (M) , see Figure 5.
3. Position pole (A) on the mounting surface
and secure using the support plate (J),
M10 washer (K), spring washer (L) and M10
bolt (I). Fasten M10 bolt using provided
wrench (P). See Figure 6.
a
m
f
Figure 4 t2 Figure 5
j
i
k
l
Figure 6

4 5
STEP 2
Install swivel arm (D) to the pole (A). Fasten the bolt with supplied Allen key (O). Attach the wire clip
(N1,N2) to the pole (A) and swivel arm (D).
STEP 1 (continued)
Option C: Grommet Base with Self-Drilled Hole
1. Position the Pole (A) on the mounting
surface and mark the center hole. Drill a
3/8” (10mm) diameter hole at the marked
position through the mounting surface.
2. Install the Grommet Base Plate (M) to the
Pole (A) using x3 M5x14 Bolts (F), and
tighten using the Allen Wrench (O), see
Figure 7.
3. Attach So Pad (T2) to the Grommet Base
Plate (M), see Figure 8.
4. Position the Pole (A) on the mounting
surface and secure using Support Plate (J),
M10 Washer (K), Spring Washer (L), and M10
Bolt (I). Fasten the M10 Bolt using provided
Wrench (P), see Figure 9.
a
m
f
Figure 7 t2 Figure 8
j
i
k
l
Figure 9
STEP 3
OPTION A: Flat Back Monitor
Attach the VESA plate (E) to the monitor with
M4x12 thumb bolts (Q).
NOTE: Hand tighten screws to avoid over
tightening.
q
OPTION B: Curved Back Monitor
Attach the VESA plate (E) to the monitor with M4x30
bolts (R) and M4 spacers (S).
NOTE: Hand tighten screws to avoid over
tightening.
s
r
Slide the monitor onto the head of swivel arm (D).
STEP 4
Install the security nut (H). Make sure the security
nut is installed before you rotate the monitor. For
minor height adjustment, use Allen key (O).
h
d
on1
n2

6 7
STEP 5 STEP 6
Manage cables and store Allen keys (O) in wire clip (N1) for future use.Tighten the bolt with the supplied Allen key (O) to fix the tilt angle and to make any necessary
adjustments.
o
o
N1
N2

Last Updated: 11/28/2018
If any parts are received damaged or defective, please contact us. We are happy to
replace parts to ensure you have a fully functioning product.
For more VIVO products, check out our website at:
www.vivo-us.com.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]om www.vivo-us.com 1-800-371-5654