Vivo STAND-V002K User manual

Pneumatic Arm Dual Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v002k
SKU: STAND-V002K
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
A (x1)
Arm
B(x2)
VESA Plate
C(x1)
Pole
J (x3)
M6x16
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
D(x1)
Clamp
E(x1)
Cable Clip
F (x1)
Grommet
Base
G(x1)
So Pad
H (x1)
Support Plate
I (x2)
Thumbscrew
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
K (x1)
4mm Allen
Wrench
L (x1)
6mm Allen
Wrench
M-A (x8)
M4x12
M-B (x8)
M4x16
M-C (x8)
M5x12
M-D (x8)
M5x16
M-E (x8)
D5 Washer
M-F (x8)
Spacer
TOOLS NEEDED
2.2-19.8lbs
(1-9kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
PER MONITOR

3
ASSEMBLY STEPS
STEP 1
Loosen the screws and disassemble the Clamp (D) using the 4mm Allen Wrench (K).
OPTION A: Clamp Installation
Attach clamp brace (D1) to the Pole (C) using
the M6x16 bolts (J) and the 4mm Allen Wrench
(K). Peel the protective film o of the So Pad
(G) and place it onto the clamp brace (D1).
OPTION B: Grommet Base Installation
For grommet hole attachment only, cut the
So Pad (G) along the indentations. Peel the
protective film o of the So Pad (G) and place
the pieces onto the Grommet Base (F) as shown
below.
STEP 2
C
K
K

4
STEP 2 (Continued)
OPTION A: Clamp Installation
For thinner desktops, re-attach the Clamp (D2)
to the Clamp Brace (D1) and tighten the screws
using the 4mm Allen Wrench (K).
For thicker desktops, disassemble the Clamp
(D2) using a Phillips screwdriver as shown in
3.1. Flip the L-bracket over and reassemble.
Then re-attach the Clamp (D2) to the Clamp
Brace (D1) and tighten the screws using the
4mm Allen Wrench (K).
OPTION B: Grommet Installation
If not using an existing through-hole, using a
10mm (⅜”) drill bit, drill through the desktop
at least 2” away from the edge. Disassemble
the Clamp (D2) using a Philips screwdriver. Set
aside all parts except for Clamp Bolt (D3). Attach
Pole (B) and Grommet Base (F) to the desktop
using the Support Plate (H) and Clamp Bolt (D3)
as shown below.
3.1
D1
K
K
B
F
While holding Arm (A) closed, cut the
shipping tie and gently release (A).

5
STEP 4
Attach VESA Plate (B) to the back of the
monitor using Screws (M-A through M-D) and
Washers (M-E). If needed, use Spacers (M-F).
STEP 5
Slide VESA Plate (B) with monitor over
bracket on Arm (A). Secure using the
Thumbscrew (I).
Slide Arm (A) onto Pole (B) and tighten using 6mm Allen
Wrench (L). Attach Cable Clip (E) to Pole (C).
STEP 3
L
A
E
A
L
C
B
B

6
STEP 6
Adjust gas spring support in Arm (A) using 6mm Allen wrench (L). Turning counter-clockwise increas-
es support, and clockwise decreases.
STEP 7
Remove bottom cover from Arm (A) by sliding it o. Organize cables and re-attach cover.
L
A
A

7
STEP 8
Adjust tilt support using 6mm Allen Wrench (L). Store Allen Wrenches (K and L) in Cable Clip (E).
Adjust as desired.
L
K
L

LAST UPDATED: 06/02/2021
REV2
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303