Voda Plumbingware VSS033 User manual

9 421027 596795
Voda Plumbingware (NZ) Ltd | Freephone: 0508 367 366 | 5 Hewlett Street, Port Whangarei 0110 | vodaplumbingware.co.nz
Stainless Steel Pro Flow Minimalist
Shower Mixer
VSS033
Congratulations on your purchase of this high quality product from Voda Plumbingware.
Please read the following before installation and retain (along with your receipt) for future reference.
TECHNICAL SPECIFICATIONS
Suitable for Mains Pressure only
Minimum Pressure = 17kPa
Maximum operating Pressure = 500kPa
Maximum operating Temperature = 75 deg. Celsius
For domestic use only.
CONFIGURATION
Mains Pressure systems Install as supplied.
Unequal Low systems Install as supplied.
Equal Low systems Install as supplied.
INSTALLATION
Prior to installation please confirm the type of pressure the tap is to be operating in:
• For unequal low pressure, install needle valve to cold port (valve included in pack). When commissioning,
adjust valve to achieve maximum performance.
• For an equal low pressure installation, simply remove the valve inserts from both inlets, prior to installation.
• For equal mains pressure, prior to installation, remove the valve inserts from both inlets.
The installation must comply with Section 5.4 of AS/NZS 3500 Standard with regard to Isolating stop cock use. As
per AS/NZS 3500.1:2300 clause 3.3.4, the maximum operating pressure at any outlet, other than a fire service outlet,
within a building does not exceed 500kpa.
To install, mount body within wall cavity, noting the free-way for the face-plate adjustment.
*IMPORTANT NOTE: If equal low or unequal low systems be sure to have minimum of 450mm straight pipe

Voda Plumbingware (NZ) Ltd | Freephone: 0508 367 366 | 5 Hewlett Street, Port Whangarei 0110 | vodaplumbingware.co.nz
ATTACH PROOF OF PURCHASE HERE
between outlet of mixer and first bend.
The cartridge nut has been torqued to factory settings, please do not adjust this settings as it will create leakage.
Ring Foreno technical services if unsure. When testing for leaks do not block o or plug outlet port. Back pressure
will damage the ceramic cartridge and void warranty. Leakage from the cartridge sha at the front of the mixer valve
is an indication of this damage. Aer the wall lining has been fitted and finished push the face-plate on. Please note
there is a small drip-hole along the side of the faceplate. This should be facing bottom to allow any water to drip
out. Fit the handle and secure by tightening the grub screw. Place Indicator button in hole (3 above). An in-line filter
is always recommended on the cold supply to protect ceramics and give longevity to the cartridge. If you have per-
formance issue please check there are no flow restrictors between the hose and the handpiece or the hose and the
shower elbow. Remove any restrictors with rubber washers. When selecting a hand shower to go with the Equaliser,
a single function handpiece and large internal bore shower hose are recommended on low pressure installations,
e.g. Foreno MonoJet handshower or FSR1 15mm Rose. These are available from your local Foreno stockist.
WARRANTY
Please refer to our website for warranty information: www.vodaplumbingware.co.nz/warranty
In the unlikely event that this product fails during its warranty period, phone our Customer Service team
immediately on 0508 FORENO (0508 367 366) – as unauthorised removal of the product may void the warranty.
CARE AND MAINTENANCE
When cleaning your Voda product (including chrome, stainless steel, coloured or any other surface coating) you
must not use any type of astringent, abrasive or citric cleaners.
We recommend using only a so, damp cloth and on occasion a mild soap solution. Try to avoid excessive
scrubbing as this could cause damage and void your warranty.