VOILE TTS User manual

Tech Tips:
1.) Always make sure the Hardwire heel assembly is centered in the ski to maintain even pre-load of
the spring cartages. If the spring cartridges come out of adjustment, rotate clockwise to tighten and
counter clockwise to loosen, to bring the heel lever back to center. (SEE FIGURE 4)
2.) Before skiing, check the forward pressure to confirm you have an adequate load on the spring
cartridges for maximum performance. (REFER AGAIN TO FIGURE 3)
3.) Voilé recommends greasing the threaded ends of the rods at the end of each season to prevent
any corrosion or oxidation of the threads. This will maintain easy adjustment of the spring cartridges.
For best results, use marine grade anti-seize grease.
Sizing: Minimum thread engagement of the spring cartridges requires 10 full revolutions.
Correct adjustment of the heel lever will provide an audible snap when the lever is engaged. With
most boots, when the lever is not engaged it should make contact with the back of the boot heel.
(SEE FIGURE 1). To adjust the length of the heel assembly, simply spin the cartridges evenly
clockwise to tighten and counterclockwise to loosen.
At their minimum length the rod will bottom out on the back of the spring cartridge and begin
pushing out the silver colored spring rod. At this point you cannot make the heel assembly length
any shorter.
Checking the forward pressure: After you initially fit your
boots, it is necessary to check the forward pressure of the heel-piece.
Release the heel lever from the boot. Note a scribed mark at the edge
of the plastic collar on the spring cartridge. (SEE FIGURE 2) Now
engage the heel lever and check the distance from the mark to the
back collar. the distance should be at least 1/8” or mm and no more
than 1/4” or 6mm to ensure optimal flex and heel retention. (SEE
FIGURE 3) The forward pressure may need to be readjusted after your
initial ski runs.
TTS Binding Instructions
PART No. 608-140 (Stiff), 608-145 (Tour), 608-147 (Tour LT)
WIRE POSITION IS FIXED ONCE MOUNTED!!! Confirm your boot sole length for desired
wire position (active or neutral) using the specs table above.
Voilé recommends an authorized dealer for all binding mounts. Mounting instructions are
written for shop technicians that have technical expertise in mounting telemark bindings.
NEUTRAL WIRE POSITION:
Boot sizes are only a general guideline and size
may vary between boot manufacturer.
SMALL 250-275
MEDIUM 280-310
LARGE 315-355
ACTIVE WIRE POSITION:
SMALL 265-290
MEDIUM 295-325
LARGE 330-370
TTS STIFF / TTS TOUR
NEUTRAL WIRE POSITION:
Boot sizes are only a general guideline and size
may vary between boot manufacturer.
MEDIUM 305-335
MEDIUM 320-350
ACTIVE WIRE POSITION:
TTS TOUR LT (LONG TRAVEL)
TTS 20mm Toe Risers
Wire/Cartridge
Assemblies
Riser Plugs
TTS Toe Pads
LEFT Tech Pin Assembly
RIGHT Tech Pin Assembly
Crampon Hooks with
alternative 1.5mm spacer
3/4” (19mm) Mounting
screws for Tech Pin Assembly
Dual LP Climbing Heels
Dual LP 2mm Spacers
55mm Climbing Wires
75mm Climbing Wires
5/8”(15mm) mounting screws
3/4” (19mm) Mounting
screws for heel pad
Flat washers for heel pad
screws
Dual LP Slot Plugs
2
2
12
2
1
1
2
6
2
2
2
2
12
4
4
2
TTS
Telemark Touring Bindings
FIGURE 4
FIGURE 3
FIGURE 1
FIGURE 2
BOOT SOLE
LENGTH RANGE (mm)
PARTS LIST

Mounting the TTS 20mm Toe Riser and Wire/Cartridge assembly:
Consult your ski manufacturer for mounting position on all skis.
Using the Voilé Mounting Jig or the enclosed paper template, make sure the Pin Line mounting position intersects the diamond
shape on the jig or template. Check drill depth before drilling. Pay special attention to narrow profile skis. ALWAYS FOLLOW SKI
MANUFACTURER GUIDELINES AND RECOMMENDATIONS FOR MOUNTING.
Check screw length to prevent “dimpling” the base.
Grind screws if necessary.
Rest the Wire/Cartridge assembly in the appopriate channel of the Toe
Riser for Neutral (front) or Active (rear) position (SEE FIGURES 5a and 5b).
THIS WIRE POSITION CANNOT BE ADJUSTED ONCE THE TOE RISER HAS
BEEN MOUNTED.
Following manufacturers guidelines, mount the TTS 20mm Toe Riser to the
ski using either wood glue or epoxy in each screw hole.
Install the Riser Plugs.
Mounting the Dual LP Heel Pad: Making sure to use the longest wire in the front position, first, install the two climbing
wires to the Dual LP in the down position. Next, position the 2mm spacer under the Dual LP heel pad.
Follow the instructions on the back of the paper template for proper heel pad mounting. Mount the heel pad so the round contour
on the back of the heel piece matches the back of the boot heel. (SEE FIGURE 7) Take care to position the heel pad correctly to
ensure the climbing wires will be centered under the boot heel and allow the heel lever assembly to be locked down for transport.
(SEE FIGURE 8)
Make sure to use included washers with screws when mounting. Slide washer over screw and mount Dual LP to the ski. The
unique slot design allows for small, fore/aft adjustments of the heel pad. Make necessary adjustments before the glue/epoxy is
allowed to set. (SEE FIGURE 9)
Attaching the Tech Pin Assembly: Assemble the Tech Pin Assembly (6a) over one of the TTS
Toe Pads (6b), with either the Crampon Hook (6c) or alternative 1.5mm spacer in the Toe Pad’s
lower notch. (SEE FIGURE 6)
Attach the Tech Pin Assembly with the lever facing the outward edge of the ski.
WARNING:
THE VOILE TTS IS NOT A SAFETY BINDING
AND HAS NO RELEASE MECHANISM
Backcountry /Telemark skiing is an inherently dangerous sport in which there is always
the possibility of bodily injury and death. VOILE TTS bindings are not safety bindings and
therefore do not decrease the inherent risk of injury associated with the sport of
backcountry skiing. The User of this product is solely responsible for learning proper
skiing techniques, avalanche awareness, and exercising good judgment.
The manufacturer, distributor, wholesaler, and retailer are not liable for any personal
injuries sustained by the use or misuse of this product.
LIMITED WARRANTY
The Voilé TTS Binding is warrantied by the
manufacturer against any defects in
materials and workmanship for a period of
one year. Warranty service and replacement
parts are available directly through Voile.
TTS
Telemark Touring Bindings
voile.com
FIGURE 7
FIGURE 5bFIGURE 5a
a.
b.
c.
FIGURE 6
FIGURE 8 FIGURE 9
NEUTRAL FRONT ACTIVE REAR