Gill 66711 User manual

Note: Track Surface is NOT included
Page 1 of 5
www.gillathletics.com
RAISED RUNWAY SYSTEM
800-637-3090
9/12/2013
All rights reserved. INSTRR100
Copyright 2013 by Gill Athletics.
INSTRUCTION MANUAL

RAISED RUNWAY SYSTEM
www.gillathletics.com
INSTRR100
9/12/2013
800-637-3090
All rights reserved. Page 2 of 5
Copyright 2013 by Gill Athletics.
INSTRUCTION MANUAL
37.62m / 2.46m = 15.29
HOW TO ORDER A POLE VAULT RUNWAY
15.29 rounds up to 16
40m - 2.38m = 37.62m
____ x RR100 - Basic Runway Section
1
____ x RR500 - PV Pit Riser Pad
____ x RR200 - Vault Box Runway Section
5. Add 2 (to support the PV Standards)
16 + 2 = 18 total basic runway sections
Sections needed, use the following formula.
1. Determine the desired runway length in meters
2. Subtract 2.38
3. Divide by 2.46
4. Round up
653.......................10
65411...................10
65611...................12
66311...................12
66511...................14
66711...................16
To determine the number of PV Pit Riser Pads needed,
consult the RR500 spec sheet for more details.
PV Pit Model Recommended Pit Riser Qty
To determine the number of Basic Runway
Example:
The NCAA recommends a minimum runway length of 40 meters.
Minimum Runway Length
NCAA..........40 meters
NFHS..........40 meters
8'-1"
137'-2"
41.80 m
7'-10"
2.38 m
2.46 m

(from the nearest edge of the landing area)
NCAA..........1 to 3 meters
Example:
NFHS..........Approx. 12 feet for boys
Long Jump Take Off Board Positions
for the sloped face of the sand box.
1
because of its specially cut interface
be a Long Jump Runway Section
first section of the runway will always
Triple Jump Runway Sections. The
____ x 435010 - Take Off Board Assembly (at least one)
HOW TO ORDER A LONG JUMP / TRIPLE JUMP RUNWAY
1
____ x RR100 - Basic Runway Section
____ x RR350 - Triple Jump Runway Section
____ x RR300 - Long Jump Runway Section
____ x RR400 - Soft Shell Sand Pit Form Long Jump Runway Section and two
A common setup would include one
NFHS..........Approx. 8 feet for girls
these three to the 16 behind the men's TJ for a total of 19 Basic Runway Sections
are TJ Sections, so second, third, and fourth sections are Basic Runway Sections. Add
Using the example above, the first section is a LJ Section and the fifth and sixth sections
15.74 rounds up to 16
38.72m / 2.46m = 15.74
40m - 1.28m = 38.72m
The NCAA recommends a minimum runway length of 40 meters.
4. Round up
3. Divide by 2.46
2. Subtract 1.28
1. Determine the desired runway length in meters
board, use the following formula.
Sections needed behind the furthest take off
4. Add 1
3. Round up or down to the nearest whole number
2. Divide by 2.46
1. Determine the desired take off board position in meters
Sections, use the following formula.
To determine the position of the Triple Jump Take Off Board
To determine the number of Basic Runway
Example:
section will be the fifth section in the runway.
4.47 rounds to 4
So the women's triple jump take off board
4 + 1 = 5
NFHS..........40 meters
meters for the triple jump take off board.
NCAA..........40 meters
For women, the NCAA recommends 11
Minimum Runway Length
11m / 2.46m = 4.47
Triple Jump Take Off Board Positions
(from the nearest edge of the landing area)
NCAA..........At least 11m (12.5m recommended) for men
NCAA..........At least 8.5m (11m recommended) for women
NFHS..........Approx. 32 feet for boys
NFHS..........Approx. 24 feet for girls
RAISED RUNWAY SYSTEM
www.gillathletics.com
9/12/2013
800-637-3090
Page 3 of 5All rights reserved. INSTRR100
Copyright 2013 by Gill Athletics.
INSTRUCTION MANUAL
9.86 m
4'-3"
1.29 m
36'-7"
11.14 m
44'-8"
31'-3"
13.61 m
"
8'-1"
2.46 m
40.70 m
" 27'-0"
1.28 m
8.23 m
9.52 m
133'-612
4'-212
32'-4"

1/2" Flat Washer
Leveling Foot
1/2"-13 Hex Nut
Adjust leveling feet to ensure the deck heights are even.
1/2"-13 Hex Nut 1/2" Flat Washer
Use the Velcro strap to connect
runway sections together
configuration for the pole vault pit being used.
SETTING UP A POLE VAULT RAISED RUNWAY
vault standards. Use the normal procedure for locating the standards. The
the space allotted. See page 2 and the pole vault pit spec sheets for sizes.
1. Start by deciding where to locate the runway. Measure out and mark it off to ensure that the runway and pole vault pit will fit in
standards should be screwed down to the Basic Runway Sections they are on.
connect the sections.
leveling feet to adjust the deck height to remove any small differences where the runway sections meet. Use the Velcro straps to
2. Start laying out the runway sections, starting with the Vault Box Runway Section. Install the leveling feet as you go. Use the
3. Next, position the two Basic Runway Sections that will support the pole
4. Lay out the PV Pit Riser Pads. See the spec sheet for the recommended
5. Set up the pole vault pit on top of the PV Pit Riser Pads.
RAISED RUNWAY SYSTEM
www.gillathletics.com
9/12/2013
800-637-3090
Page 4 of 5All rights reserved. INSTRR100
Copyright 2013 by Gill Athletics.
INSTRUCTION MANUAL
5512"

THIS WARNING IS GIVEN IN COMPLIANCE
WITH CALIFORNIA'S PROPOSITION 65:
WARNING
This product contains chemicals known to the
State of California to cause cancer, birth defects
or other reproductive harm.
9/12/2013
RAISED RUNWAY SYSTEM
800-637-3090
Page 5 of 5
INSTRR100
www.gillathletics.com
All rights reserved.
Copyright 2013 by Gill Athletics.
INSTRUCTION MANUAL
Vinyl base Panel keeps the
walls from bowing out
Corner Patches close the wall
frame after the foam is inserted
Rigid foam logs are inserted into
the wall frame to give it shape
Vinyl Wall Frame holds the
foam inserts in place
will fit in the space allotted. See page 3 for details.
shoveling the sand out later. It is also recommended that only plastic shovels be used.
recommended to lay thin plywood down inside the sand pit before filling it with sand. This will help protect the vinyl when
the four inside corners attach the corner patches. Place the vinyl base panel in the frame and velcro it down to the walls. It is
1. Start by deciding where to locate the runway. Measure out and mark it off to ensure that the runway and soft shell sand pit form
SETTING UP A LONG JUMP TRIPLE JUMP RAISED RUNWAY
connect the sections. See page 4 for details. Make sure to put locate the Triple Jump Runway Sections correctly, see page 3.
2. Insert the foam logs into the vinyl frame wall as shown below. Close the flaps of the vinyl casing to secure the foam in place. At
3. Start laying out the runway sections, starting with the Long Jump Runway Section. Install the leveling feet as you go. Use the
leveling feet to adjust the deck height to remove any small differences where the runway sections meet. Use the Velcro straps to
4. Install take off boards and/or blanking lids where needed.