Wallenstein 3036A030 User manual

Rev Jun-2021
Tieback Mount
INSTALLATION INSTRUCTIONS
3036A030

Introduction 3036A030
Tieback Mount
2
Introduction
This tieback mount is designed to work with a Wallenstein
backhoe. The backhoe must have an SQ500 universal quick-
attach plate installed (not included).
Wallenstein backhoes are designed to work with a wide variety
of skid steers. This tieback mount provides a method to attach
and detach a Wallenstein backhoe to a New Holland® L223 skid
steer.
The tieback mount kit includes parts and hardware
that are shown under Tieback Mount Parts on page
4. Make sure that all the parts are present and
not damaged from shipping.
Following are two reasons that a skid steer tieback mount is
required:
• To avoid inadvertent movement of the skid steer controls
while a person is on the backhoe.
• To reduce pressure spikes in the hydraulic lines and prevent
damage to the hydraulic system.
Some of the illustrations in this instruction are general; however,
important features are detailed to assist with installation.
Before using, installing, or maintaining this
equipment, read and understand the safety,
operation, and maintenance information in the
backhoe Operator's Manual.
If you have questions or require assistance, contact your local
dealer, the distributor, or Wallenstein Equipment.
IMPORTANT! Installation may include metric or imperial
fasteners. See the bolt head markings to identify the bolt
type.
Metric
Imperial
Wallenstein Equipment Inc. • © 2021. All rights reserved.
No part of this work may be copied, reproduced, replaced,
distributed, published, displayed, modified, or transferred in
any form or by any means except with the prior permission of
Wallenstein Equipment Inc.
Table of Contents
Introduction.................................................................2
Safety...........................................................................3
Safety Alert Symbol .........................................................3
Signal Words ...................................................................3
Safety Information............................................................3
Tieback Mounts ..........................................................4
Tieback Mount Parts........................................................4
Tools Required.................................................................5
Install the Tieback Mount.................................................5
Connect a Quick-Attach Plate..........................................7
SQ500 Universal Quick-Attach Plate ........................9
SQ500 Universal Quick-Attach Plate Parts .....................9
Install a Quick-Attach Plate on a Backhoe.....................10
Install the Toplink Assemblies ........................................ 11
Adjust the Quick-Attach Plate Position ..........................13
Common Bolt Torque Values...................................15
www.wallensteinequipment.com
Orientation
IMPORTANT! When describing directions in this instruction,
left-hand (LH) side, right-hand (RH) side, back, and front
are determined when sitting in the skid steer driver's seat,
facing the direction of forward (FWD) travel.
FWD
01681

Safety 3036A030
Tieback Mount
3
Safety
Safety Alert Symbol
This Safety Alert Symbol means:
ATTENTION! BE ALERT!
YOUR SAFETY IS INVOLVED!
The Safety Alert Symbol identifies important safety messages
on the machine and in this instruction. This symbol means
be alert to the possibility of personal injury or death. Follow
instructions provided.
Signal Words
The signal words DANGER, WARNING and CAUTION determine
the seriousness level of the warning messages in this manual.
The appropriate signal word for each message in this manual
has been selected using the following guidelines:
DANGER –
Indicates an imminently hazardous situation that, if not avoided,
will result in death or serious injury. This signal word is to be
limited to the most extreme situations typically for machine
components which, for functional purposes, cannot be shielded.
WARNING –
Indicates a potentially hazardous situation that, if not avoided,
could result in death or serious injury, and includes hazards that
are exposed when shields are removed. It may also be used to
alert against unsafe practices.
CAUTION –
Indicates a potentially hazardous situation that, if not avoided,
may result in minor or moderate injury. It may also be used to
alert against unsafe practices.
IMPORTANT – To avoid confusing equipment protection
with personal safety messages, the signal word IMPORTANT
indicates a situation that if not avoided, could result in damage
to property or the machine.
Provides additional information that is helpful.
Safety Information
WARNING!
Avoid the risk of personal injury or machine
damage! Read the backhoe Operator’s Manual
before using this equipment. Carefully read all
safety messages in the manual and follow all
safety signs on the machine.
WARNING!
Before installing this equipment:
• Position the backhoe and skid steer on dry,
level ground.
• Make sure the area around them is clear and
free of debris.
• Turn o󰀨 the skid steer engine, apply the
parking brake, and remove the key.

Tieback Mounts 3036A030
Tieback Mount
4
Tieback Mounts
Install the two tieback mounts on the skid steer.
Tieback Mount Parts
1
2
3
4
5
Fig. 1 – Tieback Mount Parts
Item Part
Number
Description Quantity
1 Z771715 Hex bolt, M12 x 1.75 x
55 mm
2
2 Not included1Washer 2
3 Not included1Lock nut 2
4 3036W031 Tieback mount, RH 1
5 3036W031H Tieback mount, LH 1
1 Use the hardware that is on the skid steer.

Tieback Mounts 3036A030
Tieback Mount
5
Tools Required
• Basic shop tools.
• One socket wrench with a 19 mm socket.
• One calibrated torque wrench with a 19 mm socket.
Install the Tieback Mount
Tieback mount item numbers are in brackets and defined under
Tieback Mount Parts on page 4.
Step 1
Place the skid steer in a safe condition:
a. Stop the skid steer on a dry, level surface.
b. Lower the coupler to the ground.
c. Apply the parking brake.
d. Turn off the engine.
e. Remove the key.
f. Activate the hydraulic controls to remove pressure from
the hydraulic system.
Step 2
Complete the following for each of the two tieback mounts
(only the RH side is shown):
a. Remove the lock nut (3) from the skid steer bolt.
b. Remove the hex bolt and washer (2) from the front of the
skid steer.
c. Place the tieback mount (4 or 5) over the skid steer bolt.
Align the center-plate hole with the bolt hole in the skid
steer.
d. Install the lock nut on the skid steer bolt.
e. Install a hex bolt (1) through the washer, through the
tieback mount, and into the skid steer.

Tieback Mounts 3036A030
Tieback Mount
6
Step 3
Use a calibrated torque wrench to tighten the two hex bolts
and two lock nuts to the specified torque (only the RH side is
shown).
For torque specifications, see Common Bolt Torque Values on
page 15.

Tieback Mounts 3036A030
Tieback Mount
7
Step 1
Align the two toplink (5) assemblies with the tieback-plate
connections.
The toplink assemblies must be perpendicular to the tieback-
plate connections. If required, move the toplink assembly
location on the main-base weldment (9). For instructions, see
Install the Toplink Assemblies on page 11.
Step 2
Complete the following for each toplink (only the LH side is
shown):
a. Align the toplink (5) with the tieback-mount connection
holes.
b. Insert a hitch pin (7) through the toplink and tieback-
mount connection.
c. Insert a lynch pin (6) through the hitch pin.
The backhoe must have an SQ500 universal quick-attach plate
installed (not included). For instructions, see SQ500 Universal
Quick-Attach Plate on page 9.
Quick-attach plate item numbers are in brackets and defined
under SQ500 Universal Quick-Attach Plate Parts on page 9.
Connect a Quick-Attach Plate

Tieback Mounts 3036A030
Tieback Mount
8
Step 3
Align and secure the quick-attach plate. Turn the toplinks to
tighten or loosen them, as required.

SQ500 Universal Quick-Attach Plate 3036A030
Tieback Mount
9
SQ500 Universal Quick-Attach Plate
An SQ500 universal quick-attach plate is not included
with the tieback mount.
If you have questions or would like more information,
contact your local dealer, the distributor, or Wallenstein
Equipment.
SQ500 Universal Quick-Attach Plate Parts
1
2
12
14
13
4
5
6
7
3
8
9
11
10
01673
Fig. 2 – SQ500 Universal Quick-Attach Plate Parts
Item Part Number Description Quantity
1 Z51919 Flat-face, FP08 x MISO16028 1
2 Z51920 Flat-face FP08 x FISO16028 1
3 3035L109 Clevis, turnbuckle 2
4 Z71540 Hex Bolt 1/2 NC x 4" 4
5 Z11501 Toplink, Cat 0 x 10–1/2" x 16" 2
6 Z12110 Lynch Pin, 3/16" 4
7 Z11232 Hitch Pin, 5/8" x 4–1/4" 4
Item Part Number Description Quantity
8 Z72251 Hex lock nut 1/2" NC 4
9 3031W101 Weldment, main base 1
10 Z14181 Roll pin 5/16" x 1–1/2" 2
11 3031M101 Shaft, lower pivot link 1
12 3031W102 Weldment, pivot backhoe 1
13 Z72271 Hex lock nut 3/4" NC 2
14 Z71720 Hex bolt, 3/4" NC x 2" 2

SQ500 Universal Quick-Attach Plate 3036A030
Tieback Mount
10
01674
Install a Quick-Attach Plate on a Backhoe
IMPORTANT! Stabilize the backhoe to prevent movement
during installation.
Quick-attach plate item numbers are in brackets and defined
under SQ500 Universal Quick-Attach Plate Parts on page 9.
For clarity, some backhoe parts are not shown in the following
image.
Tools Required
• Basic shop tools.
• One calibrated torque wrench with 1–1/16" socket.
• One 1–1/16" open-end wrench.
• One socket wrench with 1–1/16" socket.
Step 1
Align the pivot-backhoe weldment (12) with the backhoe main
frame (for information about the location of backhoe parts, see
the backhoe Operator's Manual).
Step 2
Install the eight 5/8" NC bolts (not shown) and lock nuts (not
shown); four on each side.
Step 3
Use a calibrated torque wrench to tighten the eight lock nuts to
160 lbf•ft (215 N•m).
Step 4
Install the two turnbuckle clevises (3) and toplinks (5). For
instructions, see Install the Toplink Assemblies on page 11.
Fig. 3 – Universal Quick-Attach Plate Installation

SQ500 Universal Quick-Attach Plate 3036A030
Tieback Mount
11
Install the Toplink Assemblies
Quick-attach plate item numbers are in brackets and defined
under SQ500 Universal Quick-Attach Plate Parts on page 9.
Tools Required
• Basic shop tools.
• One calibrated torque wrench with 7/8" socket.
• One 7/8" open-end wrench.
• One socket wrench with 7/8" socket.
Step 1
Align the two turnbuckle clevises (3) with the required holes in
the main-base weldment (9).
01675
Step 2
Complete the following for each turnbuckle clevis (LH and RH
side):
a. Insert two hex bolts (4) through the turnbuckle clevis and
the main-base weldment.
b. Install a lock nut (8) on each hex bolt.
c. Use a calibrated torque wrench to tighten the two lock
nuts to 80 lbf•ft (110 N•m).
01676

SQ500 Universal Quick-Attach Plate 3036A030
Tieback Mount
12
Step 3
Complete the following for each turnbuckle clevis (only the LH
side is shown):
a. Align the toplink (5) with a turnbuckle clevis.
b. Insert a hitch pin (7) through the toplink and turnbuckle-
clevis holes.
c. Insert a lynch pin (6) through the hitch pin.
01677

SQ500 Universal Quick-Attach Plate 3036A030
Tieback Mount
13
Adjust the Quick-Attach Plate Position
Quick-attach plate item numbers are in brackets and defined
under SQ500 Universal Quick-Attach Plate Parts on page 9.
Tools Required
• Basic shop tools.
• One calibrated torque wrench with 1–1/4" socket.
• One 1–1/4" open-end wrench.
• One socket wrench with 1–1/4" socket.
Step 1
Prepare the equipment:
a. Connect the quick-attach plate to the skid steer and
make sure the toplinks (5) are tight. For instructions, see
Connect a Quick-Attach Plate on page 7.
b. Rotate the skid steer plate to the full-back position against
the solid stop.
c. Support the backhoe on a skid or blocks to prevent
unexpected movement.
d. Set the skid steer parking brake.
e. Turn off the skid steer and remove the ignition key.
f. Activate the hydraulic controls to remove the pressure.
01690
The backhoe, skid steer, and tieback mounts
should not be removed. However, they are not
shown in the following images for clarity.
Step 2
Remove the hex bolt (14) and lock nut (13) from each side of
the pivot-backhoe weldment (12) (LH and RH side).
01678

SQ500 Universal Quick-Attach Plate 3036A030
Tieback Mount
14
Step 3
Rotate the pivot-backhoe weldment to adjust the backhoe
angle. Align the holes in the required position.
01679
Step 4
Complete the following on each side of the pivot-backhoe
weldment (LH and RH side):
a. Insert a hex bolt through the main-base weldment (9) and
pivot-backhoe weldment.
b. Install a lock nut on the hex bolt.
c. Use a calibrated torque wrench to tighten the hex bolt to
290 lbf•ft (390 N•m).
01680

Common Bolt Torque Values 3036A030
Tieback Mount
15
Common Bolt Torque Values
Checking Bolt Torque
The tables shown give correct torque values for various
bolts and capscrews. Tighten all bolts to the torque
values specified in the table, unless indicated otherwise.
Check tightness of bolts periodically.
IMPORTANT! If replacing hardware, use fasteners of
the same grade.
IMPORTANT! Torque figures indicated in the table are
for non-greased or non-oiled threads. Do not grease or
oil threads unless indicated otherwise. When using a
thread locker, increase torque values by 5%.
Bolt grades are identified by the bolt head
markings.
Imperial Bolt Torque Specifi cations
Bolt
Diameter
Torque Value
SAE Gr. 2 SAE Gr. 5 SAE Gr. 8
lbf•ft N•m lbf•ft N•m lbf•ft N•m
1/4" 6 8 9 12 12 17
5/16" 10 13 19 25 27 36
3/8" 20 27 33 45 45 63
7/16" 30 41 53 72 75 100
1/2" 45 61 80 110 115 155
9/16" 60 95 115 155 165 220
5/8" 95 128 160 215 220 305
3/4" 165 225 290 390 400 540
7/8" 170 230 420 570 650 880
1" 225 345 630 850 970 1320
Metric Bolt Torque Specifi cations
Bolt
Diameter
Torque Value
Gr. 8.8 Gr. 10.9
lbf•ft N•m lbf•ft N•m
M3 0.4 0.5 1.3 1.8
M4 2.2 3 3.3 4.5
M6 7 10 11 15
M8 18 25 26 35
M10 37 50 52 70
M12 66 90 92 125
M14 83 112 116 158
M16 166 225 229 310
M20 321 435 450 610
M30 1,103 1 495 1,550 2 100

www.wallensteinequipment.com