Waterworks CEKM30 Instruction sheet

STYLE No. CEKM30, CE30KM
Canteen One Hole High Profile Kitchen Faucet
with Pull-Out Spray and Oak Lever Handle
INSTALLATION GUIDELINES
PAGE 1 OF 6 | UPDATED ON 5.11.2018
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM
IMPORTANT:
To ensure this product is installed properly, you must read and
follow these guidelines.
The owner/user of this product must keep this information for
future reference.
This product must be installed by a professional licensed
contractor.
Be sure your installation conforms to federal state, and local
codes. In the State of Massachusetts, all installations must comply
with the rules and regulations set forth within 248 CMR.
Inspect this product to ensure you have all the parts required for
proper installation. Product is sold partially assembled but shown
fully disassembled for illustrative and service purposed only.
Use only a strap wrench or protected/smooth-jaw wrench on any
finished surface.
The use of certain plumber’s putty may stain stone or tile surfaces.
If further assistance is required, please contact Product Support at
1-800-927-2120 Monday through Friday, 8am – 6pm EST.
Refer to the separate Service Parts Documents for available
replacement parts.
TECHNICAL DETAILS:
DETAIL SPECIFICATION
ADJUSTABLE VERSUS FIXED SPRAY ADJUSTABLE
HANDLE TURN ANGLE QUARTER TURN
INLET CONNECTION 3/8” COMPRESSION CONNECTOR HOSES †
RESTRICTED MAXIMUM FLOW RATE 2.2gpm [8.3L/min]
SPOUT REACH 9-1/8” [231mm]
SPOUT SWIVEL YES
SPRAY HOSE LENGTH 49” [1.2m]
SPRAY INCLUDED IN UNIT YES
WATER PRESSURE RANGE 20psi [1.5 bar] MIN
85psi [6.0 bar] MAX
WATER PRESSURE RECOMMENDED 45psi [3.0 bar]
†UK Style No., CE30KM is supplied with 2 BSPP adapters, assembly required.
MOUNTING
SURFACE
Ø 2-1/8"
[54mm]
FITTINGS
HOLE
1/4" MIN
[6mm]
2-1/4" MAX
[57mm]
DECK
THICKNESS

STYLE No. CEKM30, CE30KM
Canteen One Hole High Profile Kitchen Faucet
with Pull-Out Spray and Oak Lever Handle
PAGE
2 OF 6 | UPDATED ON 5.11.2018
PRODUCT SUPPORT |
800.927.2120 | WATERWORKS.COM
INSTALLATION GUIDELINES
RUBBER WASHER
[DO NOT REMOVE]
SPOUT SHANK
RUBBER WASHER
PLASTIC WASHER
NUT
1. Unthread and remove the NUT from the SPOUT SHANK
then remove the PLASTIC and RUBBER WASHERS.
NOTE: Do NOT remove the RUBBER WASHER beneath
the ESCUTCHEON.
SUPPLY TUBE
[BLUE LABEL]
SUPPLY TUBE
[RED LABEL]
SUPPLY
HOSE SPRAY
SUPPLY HOSE
SUPPLY
HOSE
SPRAY
SUPPLY HOSE
SUPPLY HOSE
MOUNTING
SURFACE
RUBBER WASHER
ESCUTCHEON †
HANDLE ‡
[RIGHT
SIDE ONLY]
† A RUBBER WASHER for the
ESCUTCHEON is provided.
If desired, a bead of caulk or clear
silicone may be applied where the
ESCUTCHEON contacts the
mounting surface.
‡ RIGHT HAND HANDLE
INSTALLATION ONLY
2. Thread and securely tighten the SUPPLY HOSES onto the
SUPPLY TUBES pre-installed on the SPOUT.
NOTE: The HOSES are M10 x 3/8” COMPRESSION
CONNECTOR HOSES and the SUPPLY TUBES are marked
BLUE for cold and RED for hot.
3. Insert the SPOUT through the hole on the mounting
surface making sure the RUBBER WASHER provided is
beneath the ESCUTCHEON and the HANDLE is aligned on
the RIGHT SIDE of the SPOUT.
NOTE: The HANDLE can ONLY be installed on the RIGHT
SIDE.

STYLE No. CEKM30, CE30KM
Canteen One Hole High Profile Kitchen Faucet
with Pull-Out Spray and Oak Lever Handle
PAGE
3 OF 6 | UPDATED ON 5.11.2018
PRODUCT SUPPORT |
800.927.2120 | WATERWORKS.COM
INSTALLATION GUIDELINES
SPOUT
SHANK
RUBBER
WASHER
PLASTIC
WASHER
NUT
SUPPLY HOSE
SPRAY
SUPPLY HOSE
4. Slide the WASHERS and NUT over the HOSES then thread
and securely tighten the NUT onto the SPOUT SHANK.
NYLON
SPRAY HOSE
SPOUT
NYLON
SPRAY HOSE
[MALE END]
CAP
1.
3.
2.
[GUIDE HOSE MANUALLY!]
SPRAY SUPPLY
HOSE
ADAPTER
NYLON SPRAY HOSE
[FEMALE END]
FLOW
REGULATING
CHECK
VALVE CHECK
VALVE
5. Unthread and remove the CAP from the top of the SPOUT
then insert the MALE END of the NYLON SPRAY HOSE
through the bottom of the SPOUT and, from above,
manually guide the HOSE out of the SPOUT.
6. Thread and securely tighten the FEMALE END of the
NYLON SPRAY HOSE onto SPRAY SUPPLY HOSE using
the ADAPTER provided.
NOTE: A FLOW REGULATING CHECK VALVE is located
inside the ADAPTER as well as an additional CHECK
VALVE.

STYLE No. CEKM30, CE30KM
Canteen One Hole High Profile Kitchen Faucet
with Pull-Out Spray and Oak Lever Handle
PAGE
4 OF 6 | UPDATED ON 5.11.2018
PRODUCT SUPPORT |
800.927.2120 | WATERWORKS.COM
INSTALLATION GUIDELINES
HOT SUPPLY VALVE
[SOLD SEPARATELY]
SUPPLY HOSE ‡
COLD SUPPLY VALVE
[SOLD SEPARATELY]
SUPPLY HOSE ‡
‡ UK installations only!
2 BSPP ADAPTERS, 9/16"-24 UNEF Male x 3/8" Female BSPP,
for the SUPPLY HOSES are provided.
7. Connect the SUPPLY HOSES to the SUPPLY VALVES
[sold separately].
NOTE: The HOSES are connected to SUPPLY TUBES that
are marked BLUE for cold and RED for hot.
HANDLE
COLD
HOT
OFF
[CHECK FOR LEAKS!]
ON
* TURN ON THE WATER
COLLAR
SPRAYER
NYLON
SPRAY HOSE
[MALE END]
COLLAR
8. Turn on the water and operate the HANDLE to ensure it
functions properly and to flush out any debris in the
supply lines then check all connections for leaks and turn
off the water.
CAUTION: Flush out the supply lines prior to installing the
SPRAYER.
9. Unthread and remove the COLLAR from the SPRAYER
inlet then slide the COLLAR over the SPRAY HOSE.

STYLE No. CEKM30, CE30KM
Canteen One Hole High Profile Kitchen Faucet
with Pull-Out Spray and Oak Lever Handle
PAGE
5 OF 6 | UPDATED ON 5.11.2018
PRODUCT SUPPORT |
800.927.2120 | WATERWORKS.COM
INSTALLATION GUIDELINES
SPRAYER
RUBBER
WASHER
NYLON SPRAY HOSE
[MALE END]
COLLAR
10. Thread and securely tighten the SPRAY HOSE into the
SPRAYER using the RUBBER WASHER provided then
thread and securely tighten the COLLAR back onto the
SPRAYER.
NOTCH
[ON SPOUT]
PIN
[ON SPRAYER]
CAP
SPRAYER
NYLON SPRAY HOSE
WEIGHT
SCREWS
11. Insert the SPRAYER into the SPOUT then thread the CAP
back onto the top of the SPOUT.
NOTE: Ensure the PIN at the base of the SPRAYER fits
properly into the NOTCH on the SPOUT.
12. Align and press the two halves of the WEIGHT over the
SPRAY HOSE in the desired position then thread and
securely tighten the SCREWS provided.

STYLE No. CEKM30, CE30KM
Canteen One Hole High Profile Kitchen Faucet
with Pull-Out Spray and Oak Lever Handle
PAGE
6 OF 6 | UPDATED ON 5.11.2018
PRODUCT SUPPORT |
800.927.2120 | WATERWORKS.COM
INSTALLATION GUIDELINES
SPOUT
[180° SWIVEL]
BUTTON
[PUSH AND HOLD TO
ADJUST SPRAY]
HANDLE
WEIGHT
[ADJUST POSITION
IF OBSTRUCTED]
SPRAYER
* TURN ON THE WATER
13. Turn on the water and operate the SPRAYER to ensure it
functions properly making sure the WEIGHT can move
freely beneath the cabinet and the SPOUT is able to swivel
properly. Adjust the position of the WEIGHT if necessary.
NOTE: To adjust the SPRAY, press and hold the BUTTON
on the side of the SPRAYER.
SET SCREW
[2mm HEX]
GLAND
COVER
HANDLE
CARTRIDGE
RETAINING
COLLAR
GLAND
COVER
HANDLE
SERVICING THE CARTRIDGE:
1. Unthread the GLAND COVER to expose the SET SCREW
then loosen, but do NOT remove, the SET SCREW using a
2mm HEX KEY.
2. Remove the HANDLE then unthread and remove the
RETAINING COLLAR to exposed and remove the
CARTRIDGE.