WCP Omio CNC User manual

Page 1
wcproducts.com
Omio CNC Router Enclosure (Base) -
User Guide (Rev 1)
Table of Contents

Omio CNC Router Enclosure (Base) -
User Guide (Rev 1)
Page 2
wcproducts.com
Table of Contents
Table of Contents
What is the Omio CNC Router Enclosure? ��������������������������������������������������������3
Omio CNC Router Enclosure Assembly Instructions ���������������������������������������5
Step 1 ���������������������������������������������������������������������������������������������������������6
Step 2 ���������������������������������������������������������������������������������������������������������7
Step 3 ���������������������������������������������������������������������������������������������������������8
Step 4 ���������������������������������������������������������������������������������������������������������9
Step 5 ������������������������������������������������������������������������������������������������������ 10
Step 6 ������������������������������������������������������������������������������������������������������ 11
Step 7 ������������������������������������������������������������������������������������������������������ 12
Step 8 ������������������������������������������������������������������������������������������������������ 13
Step 9 ������������������������������������������������������������������������������������������������������ 14
Step 10 ���������������������������������������������������������������������������������������������������� 15
Step 11 ���������������������������������������������������������������������������������������������������� 16
Step 12 ���������������������������������������������������������������������������������������������������� 17
Installing Router Enclosure ����������������������������������������������������������������������������� 18
Kit Contents ����������������������������������������������������������������������������������������������������� 19
Revision Table ������������������������������������������������������������������������������������������������� 24

Omio CNC Router Enclosure (Base) -
User Guide (Rev 1)
Page 3
wcproducts.com
Table of Contents
What is the Omio CNC Router Enclosure?
The Omio CNC Router Enclosure was designed to contain the chips that are produced
by the Omio CNC Router when cutting. This makes it much safer to be used in a shop or
classroom environment. The Enclosure will also help reduce some of the noise that is
made while the Omio CNC Router is being used. This Enclosure was designed to be used
with the Omio CNC Router Stand (WCP-0342) and will bolt directly to it.
Features:
• Fully enclosed to reduce the mess produced by the machine and keep operators
safe
• Door in front and back for ease of access to all parts of machine
• Magnetic door to hold door in the up position
• Sliding door to reduce overall footprint
• Bearings on door for smooth opening
• Bolts directly to Omio CNC Router Stand

Omio CNC Router Enclosure (Base) -
User Guide (Rev 1)
Page 6Table of Contents
wcproducts.com
Step 1
Slide a 1” x 1” tube plug into the tube plug adapter. Then slide both into the tubing. Align
the tapped holes on the sides of the tube plug with the clearance holes in the tubing.
Install the two #10-32 x 3/8”L BHCS.
Repeat this step on all 1” x 1” x1/16” tubing that has the same hole pattern on the ends.
Therewillbeveplugsandadaptersintotalthatneedtobeinstalled.
Note: Some plugs may not be a slip t and may need to be tapped in with a mallet. This
is due to the inconsistency with the tubing.

Omio CNC Router Enclosure (Base) -
User Guide (Rev 1)
Page 7Table of Contents
wcproducts.com
Step 2
Placetubingonaatsurfaceasshownbelow.All#10-32rivnutsshouldbefacingdown.
Installtheve#10-32x3/8”LBHCSscrewsintoeachtubingpluginthelocationsshown
below.
Repeat this step with the other set of tubing. There should be two identical assemblies
after this step.
Note: Assembly for this step will be easier if all components are placed on a table so
that there is access to the side holes.

Omio CNC Router Enclosure (Base) -
User Guide (Rev 1)
Page 8Table of Contents
wcproducts.com
Step 3
Attach the magnet and magnet mount using the two #10-32 bolts as shown below. The
3/4”L bolt will thread into the tube plug but the 1.5”L bolt will thread into the Top Plastic
Panel in a later step.
Repeat this step on the opposite end of this tube.
Repeat on the other Tube 4 as well. There should be two identical pieces after this step.

Omio CNC Router Enclosure (Base) -
User Guide (Rev 1)
Page 9Table of Contents
wcproducts.com
Step 4
Install the tubes as shown below using four #10-32 x 3/8”L bolts. Tube 5 will get an
additional bolt on each end that will go on the bottom side of the tube and thread into
the tube plug, shown in Detail A.
Tube 4 is the assembly from Step 3 with the magnets facing down.

Omio CNC Router Enclosure (Base) -
User Guide (Rev 1)
Page 10Table of Contents
wcproducts.com
Step 5
Attach the Plastic Side Panel as shown using the #10-32 x 1/2”L bolts. The counter
bores in the plastic panel need to face the rivnuts in the tubing.
Repeat this step for the opposite side of the enclosure.

Omio CNC Router Enclosure (Base) -
User Guide (Rev 1)
Page 11Table of Contents
wcproducts.com
Step 6
Attach the Plastic Top Panel as shown using the #10-32 x 1/2”L bolts. The counter bores
in the plastic panel need to face the rivnuts in the tubing.
Thread the loose bolt from Step 3 into the Plastic Top Panel.

Omio CNC Router Enclosure (Base) -
User Guide (Rev 1)
Page 13Table of Contents
wcproducts.com
Step 8
Install the 3D printed bearing guides and bearing in the locations shown below. Do not
over tighten the bolts as this will cause the bearings to bind. Tighten enough so that the
3D printed parts are tight against the plastic.
Repeat this for all four corners of the Omio CNC Router Enclosure.
Note: The threads of the bolts will needed to be sanded down a bit for them to t into
the bearings. This can be accomplished with a hand drill and some sandpaper.

Omio CNC Router Enclosure (Base) -
User Guide (Rev 1)
Page 14Table of Contents
wcproducts.com
Step 9
Install the three bolts and bearings into the Bearing Top Guide, as shown below.
Repeat this step for all four Bearing Top Guides (both versions).
Note: The threads of the bolts will needed to be sanded down a bit for them to t into
the bearings. This can be accomplished with a hand drill and some sandpaper.

Omio CNC Router Enclosure (Base) -
User Guide (Rev 1)
Page 16Table of Contents
wcproducts.com
Step 11
InstallthemagnetintotheDoorMagnetHolderusingthetwo#6-32atheadbolts
prior to installing the Door Magnet Holder to the door. Repeat for all four magnets and
Holders.
Use two #10-32 x 1/2”L BHCS and nuts to attach the Door Magnet Holder to the Plastic
Door. Repeat for all four Door Magnet Holders.
Note: Be sure to check the polarity of the magnets before installing them� This magnet
and the one installed in Step 3 need to attract each other. Check that the door is held
up and that there is no gap between the magnets. If there is, then one magnet may
need to be ipped.

Omio CNC Router Enclosure (Base) -
User Guide (Rev 1)
Page 17Table of Contents
wcproducts.com
Step 12
Cut the rubber trim to the desired length to cover the bottom edge of the door. It is
recommended to leave 1/4”- 1/2” gap at the end of the door uncovered so that the
rubber does not rub on the side panels. Press the rubber trim onto the bottom edge of
the door.
Repeat this process for the other door.

Omio CNC Router Enclosure (Base) -
User Guide (Rev 1)
Page 18Table of Contents
wcproducts.com
Installing Router Enclosure
Attach the Omio CNC Router Enclosure to the Omio CNC Router Stand using the ten
#10-32 x 1.5”L BHCS. Get all bolts started before fully tightening them.
Note: If the Enclosure is not being installed on the Omio CNC Router Stand, the same
holes can be used to attach whatever the surface may be.
Table of contents