WCP WCP-EX-0007 User guide

Page 1
wcproducts.com
WCP-EX-0007 - Application Guide
(Rev 1)
Table of Contents

Page 2
wcproducts.com
WCP-EX-0007 - Application Guide
(Rev 1)
Table of Contents
Table of Contents
What is the GreyT Telescope? ���������������������������������������������������������������������������3
Non-Flipped Hooks ��������������������������������������������������������������������������������������������4
Flipped Hooks ����������������������������������������������������������������������������������������������������5
Flipped Mounting Example ��������������������������������������������������������������������������������6
Revision Table ����������������������������������������������������������������������������������������������������7

Page 3
wcproducts.com
WCP-EX-0007 - Application Guide
(Rev 1)
Table of Contents
What is the GreyT Telescope?
The Greyt Telescope kit lets you make a linear telescoping system with little to no
effort. Up to 40 inches per stage, up to 4 stages, and more than enough power from the
Falcon 500 motor. Lock your telescope in place with either the Ratchet & Pawl or the
WCP Friction Brake. Use it for fast and secure climbs, or any other ne-controlled linear
mechanisms.
Notable features:
• Congurable, up to 4 stages.
• Easy to assemble and maintain.
• All bearings, no sliders.
• Integrated gearbox and mounting.
• Built in option for Ratchet & Pawl or WCP Friction Brake.
• Works with .060” and .125” tubing.
• No CNC machining required.
• Proper hardstops.
• Improved design, removes common failure point of internal bolts.

Page 4Table of Contents
wcproducts.com
WCP-EX-0007 - Application Guide
(Rev 1)
Non-Flipped Hooks
In the image below are example hooks that could be used for hanging. The hooks are
made from 1/8” thick aluminum and are bolted together using 1”L spacers. These will
help keep the hooks from bending.
A 3/8” OD Shaft is installed through both hooks and the 1x1 Output Tube. In this
example, this acts as an anchor point for the string.

Page 5Table of Contents
wcproducts.com
Flipped Hooks
The image below shows example hooks that could be used for either of the Flipped
congurations. The hooks are made from 1/8” thick aluminum and are bolted together
using 1”L spacers. These will help keep the hooks from bending.
A 3/8” OD Shaft is used as the anchor point for the string. Unlike the Non-Flipped Hooks,
the shaft is installed outside the tube for the Flipped congurations. The position for the
shaft is indicated in the image below.
Note: When designing your hook, make sure that the anchor point does not cause the
string to collide with any of the CF Springs�
WCP-EX-0007 - Application Guide
(Rev 1)

Page 6Table of Contents
wcproducts.com
Flipped Mounting Example
For this mounting example, you will need 2 Aluminum Nutstrips cut to 3”. For one of the
nuststrips, drill out the two holes marked in green to #9.
Remove the two #10-32 x 3”L bolts indicated in the image below. Drill out the
corresponding tapped holes on the Gearbox Plate clearance for #10-32 bolts. Install the
nutstrips as shown in the image below using the indicated bolts.
WCP-EX-0007 - Application Guide
(Rev 1)

Page 7Table of Contents
wcproducts.com
WCP-EX-0007 - Application Guide
(Rev 1)
Revision Table
Revision Date Revision # Description
11/24/2021 1.0 First revision created.