WCP Omio CNC Router Stand User manual

Page 1
wcproducts.com
Omio CNC Router Stand (Mobile Cart) -
User Guide (Rev 1)
Table of Contents

Omio CNC Router Stand (Mobile Cart) -
User Guide (Rev 1)
Page 2
wcproducts.com
Table of Contents
Table of Contents
What is the Omio CNC Router Stand (Mobile Cart)? ���������������������������������������3
Omio CNC Router Stand Assembly Instructions ����������������������������������������������5
Assembly Note ������������������������������������������������������������������������������������������6
Step 1 ��������������������������������������������������������������������������������������������������������7
Step 2 ������������������������������������������������������������������������������������������������������ 10
Step 3 ������������������������������������������������������������������������������������������������������ 11
Step 4 ������������������������������������������������������������������������������������������������������ 12
Step 5 ������������������������������������������������������������������������������������������������������ 13
Step 6 ������������������������������������������������������������������������������������������������������ 14
Step 7 ������������������������������������������������������������������������������������������������������ 15
Step 8 ������������������������������������������������������������������������������������������������������ 16
Step 9 ������������������������������������������������������������������������������������������������������ 17
Step 10 ���������������������������������������������������������������������������������������������������� 18
Step 11 ���������������������������������������������������������������������������������������������������� 19
Step 12 ���������������������������������������������������������������������������������������������������� 20
Step 13 ���������������������������������������������������������������������������������������������������� 21
Installing Omio X8 CNC Router ���������������������������������������������������������������������� 22
Step 1 ������������������������������������������������������������������������������������������������������ 23
Step 2 ������������������������������������������������������������������������������������������������������ 24
Leveling Router Stand ������������������������������������������������������������������������������������� 25
Kit Contents ����������������������������������������������������������������������������������������������������� 26
FAQ ������������������������������������������������������������������������������������������������������������������� 30
Revision Table ������������������������������������������������������������������������������������������������� 31

Omio CNC Router Stand (Mobile Cart) -
User Guide (Rev 1)
Page 3
wcproducts.com
Table of Contents
What is the Omio CNC Router Stand (Mobile
Cart)?
The Omio CNC Router Stand is a sturdy, mobile table for the Omio X8-2200L-USB (WCP-
0341). The stand will hold the computer or laptop used to control the router as well as
the control box. The stand is large enough to accommodate an enclosure, if desired.
Everything needed to operate the Omio X8-2200L is contained in one mobile unit.
Features:
• Designed for the Omio X8-2200L-USB (WCP-0341)
• Smaller routers may be used as well
• Overall Dimensions: 53”L x 38”W x 35.5”H
• 2” x 2” aluminum tubing construction
• Casters with leveling pads
• MaterialStorage(6sections)ts2’x4’sheet
• Monitor arm mounting holes
• Storage space for other accessories and tools
• Omio Enclosure (WCP-0343) bolts directly to cart
• Weight Capacity - 500 lbs

Omio CNC Router Stand (Mobile Cart) -
User Guide (Rev 1)
Page 5Table of Contents
wcproducts.com
Omio CNC Router Stand Assembly Instructions
The following outlines the assembly instructions for the Omio CNC Router Stand. All
tubing will be labeled with its own number to help with assembly. Tubing locations can
also be found in the CAD model available on the product page.
Rivnuts will come pre-installed where needed.

Omio CNC Router Stand (Mobile Cart) -
User Guide (Rev 1)
Page 6Table of Contents
wcproducts.com
Assembly Note
Due to variations and differences in quality of the aluminum extrusion, WCP will install all
tube plugs into the ends of the tubing where they are required. We do this to ensure all
tubeplugstcorrectly.Step1canbeskippedasitwillbecompletedbeforeshipping.
When installing the 2” x 2” tube plugs, the following illustrations show the maximum
amount of bolts that can be added to each tube. We have provided the amount that is
necessary for the cart to be assembled correctly and more may be added if desired.
Each tube plug only requires two bolts per side as opposed to the three seen in Step
1. Additionally, only four bolts are needed to attach one tube to an adjacent tube as
opposedtoveasseenintheremainingassemblysteps.

Omio CNC Router Stand (Mobile Cart) -
User Guide (Rev 1)
Page 7Table of Contents
wcproducts.com
Step 1
2” x 2” Tube Plug
Slide a 2” x 2” tube plug into the tube. Align the tapped holes on the sides of the tube
plug with the clearance holes in the tubing. Install the six #10-32 x 3/8”L BHCS.
Repeat this step on all 2” x 2” tubing that has the same hole pattern on the ends. There
will be 33 plugs in total that need to be installed.
Note: Some plugs may not be a slip t and may need to be tapped in with a mallet. This
is due to the inconsistency with the tubing.

Omio CNC Router Stand (Mobile Cart) -
User Guide (Rev 1)
Page 8Table of Contents
wcproducts.com
1”x1” Tube Plug (1/16” Wall Tubing)
Slide a 1” x 1” tube plug into the tube plug adapter. Then slide both into the tubing. Align
the tapped holes on the sides of the tube plug with the clearance holes in the tubing.
Install the two #10-32 x 3/8”L BHCS.
Repeat this step on all 1” x 1” x1/16” tubing that has the same hole pattern on the ends.
Therewillbeveplugsandadaptersintotalthatneedtobeinstalled.
Note: Some plugs may not be a slip t and may need to be tapped in with a mallet. This
is due to the inconsistency with the tubing.

Omio CNC Router Stand (Mobile Cart) -
User Guide (Rev 1)
Page 9Table of Contents
wcproducts.com
1”x1” Tube Plug (1/8” Wall Tubing)
Slide a 1” x 1” tube plug into the tube. Align the tapped holes on the sides of the tube
plug with the clearance holes in the tubing. Install the two #10-32 x 3/8”L BHCS.
Repeat this step on all 1” x 1” x1/8” tubing that has the same hole pattern on the ends.
There will be ten plugs in total that need to be installed.
Note: Some plugs may not be a slip t and may need to be tapped in with a mallet. This
is due to the inconsistency with the tubing.

Omio CNC Router Stand (Mobile Cart) -
User Guide (Rev 1)
Page 10Table of Contents
wcproducts.com
Step 2
Placetubingonaatsurfaceasshownbelow.All#10-32rivnutsshouldbefacingup
with the 1/4-20 rivnuts in each corner facing down.
Installtheve#10-32x3/8”LBHCSscrewsintoeachtubingpluginthelocationsshown
below.
Note: Assembly for this step will be easier if all components are placed on a table so
that there is access to the side holes�

Omio CNC Router Stand (Mobile Cart) -
User Guide (Rev 1)
Page 11Table of Contents
wcproducts.com
Step 3
Place the MDF Cart Base on top of the aluminum structure from the previous step. The
counter bores in the MDF Cart Base will line up with the rivnuts in the tubing. Install all
#10-32 x 1.25”L bolts.
Note: DO NOT over tighten the bolts�

Omio CNC Router Stand (Mobile Cart) -
User Guide (Rev 1)
Page 15Table of Contents
wcproducts.com
Step 7
Place the MDF Short Shelf and MDF Long Shelf on top of the aluminum structure from
the previous step. The counter bores in the MDF Shelf will line up with the rivnuts in the
tubing. Install all #10-32 x 1.25”L bolts.
Note: DO NOT over tighten the bolts�

Omio CNC Router Stand (Mobile Cart) -
User Guide (Rev 1)
Page 16Table of Contents
wcproducts.com
Step 8
Install all tubes as shown in the locations shown below. Use four #10-32 x 3/8”L bolts to
secure each end of tube in place. Install as many sets of dividers as desired.
Note: Some angle iron may be installed on the wood base directly under each 1” x 1”
piece of tubing to help prevent sheets from sliding around, if the cart will be moved
often� This is an optional addition and parts are not included�

Omio CNC Router Stand (Mobile Cart) -
User Guide (Rev 1)
Page 17Table of Contents
wcproducts.com
Step 9
Placetubingonaatsurfaceasshownbelow.All#10-32rivnutsshouldbefacingup.
Installtheve#10-32x3/8”LBHCSscrewsintoeachtubingpluginthelocationsshown
below.
Note: Assembly for this step will be easier if all components are placed on a table so
that there is access to the side holes�

Omio CNC Router Stand (Mobile Cart) -
User Guide (Rev 1)
Page 20Table of Contents
wcproducts.com
Step 12
Flip the assembly right side up, as seen below. Align the Aluminum Cart Top with the
rivnuts in the top of the cart assembly. The counter bores in the aluminum sheet will be
facing the rivnuts. Use twelve #10-32 x 1/2”L BHCS to attach the sheet to the cart.
Note: If an enclosure is not to be installed, additional #10-32 x 1/2”L BHCS can be add-
ed into the unused holes�
Table of contents
Other WCP Rack & Stand manuals