weintek iR-AQ04-VI User manual

User Manual
iR-AQ04-VI iR-AM06-VI iR-AI04-VI
This guide walks through important information about iR-Axxx-VI Series.
V1.00

Table of Contents
1. Product Overview ...................................................................................................1
2. Specifications..........................................................................................................2
Modules Specification....................................................................................22.1
Analog Input Specification .............................................................................22.2
Analog Output Specification ..........................................................................22.3
3. LED Insicators..........................................................................................................3
L.V LED............................................................................................................33.1
RUN LED .........................................................................................................33.2
ERR LED ..........................................................................................................33.3
STA LED...........................................................................................................33.4
4. Error Handling.........................................................................................................3
5. Wiring .....................................................................................................................5
6. Analog I/O Features................................................................................................9
Feature List.....................................................................................................96.1
User-Defined Conversion Rate.......................................................................96.2
Analog Output –Soft Start...........................................................................116.3
Diagnose.......................................................................................................126.4
Analog Input –Fast Conversion Mode .........................................................126.5
Analog Input –Filter.....................................................................................136.6
7. Registers................................................................................................................13
8. iR-ETN Coupler Address Mapping.........................................................................18
9. iR-COP Coupler Address Mapping ........................................................................20

iR-AQ04-VI iR-AM06-VI iR-AI04-VI
1
1. Product Overview
a
Terminal
b.c
Expansion Connector
81mm [3.19"]
109mm [4.29"]
27mm [1.06"]
Top View
Side View
iR-AXXX
Side View
Bottom View
a
b
c
27mm [1.06"]
iR-AQ04-VI
a

iR-AQ04-VI iR-AM06-VI iR-AI04-VI
2
2. Specifications
Modules Specification2.1
Module Name
iR-AI04-VI
iR-AM06-VI
iR-AQ04-VI
Number of Analog Inputs
4
4
0
Number of Analog outputs
0
2
4
Current Consumption
70mA@5VDC
70mA@5VDC
65mA@5VDC
Analog Power Supply
24 VDC（20.4 VDC~28.8 VDC）（ -15%~+20%）
Specification
PCB Coating
Yes
Enclosure
Plastic
Dimensions WxHxD
27 x 109 x 81 mm
Weight
Approx. 0.12 kg
Mount
35mm DIN rail mounting
Environment
Protection Structure
IP20
Storage Temperature
-20°~ 70°C (-4°~ 158°F)
Operating Temperature
0°~ 55°C (32°~ 131°F)
Relative Humidity
10% ~ 90% (non-condensing)
Vibration Resistance
Conforms to EN 60068-2-6 / EN 60068-2-27
Connection
Cross-section
AWG 28-16
AWG 24-16
Certification
EMC Immunity
Conforms to
EN 55032: 2012+AC: 2013, Class A
EN 61000-6-4: 2007+A1:2011
EN 55024: 2010+A1: 2015
EN 61000-6-2:2005
Analog Input Specification2.2
Input Range
-10V~10V、-20mA~20mA
Conversion Time
2ms/Channel
Isolation
500 VDC：(Analog / Digital)
Data Format
-10~10V
-5V~5V
1~5V
-20~20mA
4~20mA
±32000
±32000
0~32000
±32000
0~32000
Resolution
0.312mV
0.156mV
0.156mV
0.625uA
0.625uA
16 bit
16 bit
15 bit
16 bit
15 bit
Input Impedance
1MΩ
250 Ω
Diagnose
Supply Voltage
Wire break (1~5V & 4~20mA)
Overflow/underflow
Accuracy
± 0.2 % Full Scale@25°C
± 0.3 % Full Scale@0°~ 55°C
Analog Output Specification2.3
Output Range
-10V~10V、-20mA~20mA
Conversion Time
1.6ms/4 channels
1.3ms/3 channels
1ms/2 channels
700us/1 channel
Isolation
500 VDC：(Analog / Digital)
Data Format
-10~10V
-5V~5V
1~5V
-20~20mA
4~20mA
±32000
±32000
0~32000
±32000
0~32000
Resolution
5mV
5mV
5mV
10uA
10uA
12bit
11bit
10bit
12bit
11bit
Output Impedance
≧1kΩ
≦500Ω
Diagnose
Supply Voltage
Open Circuit Voltage
Short Circuit Current
Accuracy
± 0.2 % Full Scale@25°C
± 0.3 % Full Scale@0°~ 55°C

iR-AQ04-VI iR-AM06-VI iR-AI04-VI
3
3. LED Insicators
L.V LED3.1
State
Description
OFF
24V power normal
Blinking
Detect 24V power
ON
24V power error
RUN LED3.2
State
Description
OFF
No Power
Blinking
iBus initiating
ON
iBus working
ERR LED3.3
State
Description
OFF
No error
Blinking
Analog channel error
ON
Unable to perform conversion
(Analog hardware error)
STA LED3.4
State
Description
OFF
No error
Blinking
Conversion in progress
4. Error Handling
State
Description
Error Handling
L.V LED ON
24V power error
Check 24V power
L.V LED Blinking
Detect 24V power
Check 24V power
Run LED is OFF
No Power
Check whether the coupler is
properly powered, or if module
malfunction occurs. And send the
malfunction unit for repair.
ERR LED ON
Unable to perform conversion
Hardware error, send the unit for
repair.

iR-AQ04-VI iR-AM06-VI iR-AI04-VI
4
RUN LED Blinking
iBus initiating
Check whether the coupler is
functioning, if not, sent the unit for
repair.
ERR LED Blinking
Channel conversion error
Check the error code to find out
whether the output value exceeds
allowable range, or voltage short
circuit / current open circuit occurs.

iR-AQ04-VI iR-AM06-VI iR-AI04-VI
5
5. Wiring

iR-AQ04-VI iR-AM06-VI iR-AI04-VI
6
2-, 3- and 4-wire Analog Sensor connection at inputs:
2 wire：

iR-AQ04-VI iR-AM06-VI iR-AI04-VI
7
3 wire：

iR-AQ04-VI iR-AM06-VI iR-AI04-VI
8
4 wire：
※AG connected to V- contact with low-resistance.

iR-AQ04-VI iR-AM06-VI iR-AI04-VI
9
6. Analog I/O Features
Feature List6.1
No.
Feature
Descriptions
1
User-Defined Conversion Rate
2
Analog Output –Soft Start
3
Diagnose
Analog Output
Voltage Short Circuit Detection & Protection
Voltage Open Circuit Detection & Protection
4
Analog Input
Disconnection Detection (1-5v / 4-20mA)
5
Analog Input –Fast Conversion Mode
6
Analog Input –Digital Filter
User-Defined Conversion Rate6.2
iR-Axxx-VI Series models support built-in digital-to-analog conversion with
user-defined range. Available ranges are: ±10V, ±5v, 1-5v, ±20m, 4-20mA.
Example: When the defined mode is ±10V, the default scale range is ±32000.
Converting analog value 10v will get the upper limit of the range, which is 32000.
Converting analog value -10v will get the lower limit of the range, which is -32000.
10v
Upper Limit
Lower Limit -10v
5v
-5v 1v
5v
-20mA
20mA
4mA
20mA
Mode: ±10v ±5v 1-5v ±20mA 4-20mA

iR-AQ04-VI iR-AM06-VI iR-AI04-VI
10
Mode: ±10v
Mode: ±5v
Upper Limit
Lower Limit
10v
-10v
Upper Limit
Lower Limit
5v
-5v
Mode: 1-5v
Mode: ±20mA
Upper Limit
Lower Limit
5v
1v
Upper Limit
Lower Limit
20mA
-20mA
Mode: 4-20mA
Upper Limit
Lower LimIt
20mA
4mA
The upper and lower limit of the scale range can be configured for each mode. When
switching from one mode to another, the upper and lower limit will return to default;
therefore, when using this feature, please set the mode before configuring the range.
By default the upper and lower limit of the range for each mode is as below:
Mode
Minimum
Maximum
-10~10V
-32000
32000
-5V~5V
-32000
32000
1~5V
0
32000
-20~20mA
-32000
32000
4~20mA
0
32000

iR-AQ04-VI iR-AM06-VI iR-AI04-VI
11
Analog Output –Soft Start6.3
Generally, when changing analog output value, the voltage or current output will
change immediately. To gradually increase or decrease output for reducing potential
system impact, an [Output Update Time] parameter can be configured. Adjusting
Output Update Time can get a slew rate where the change of voltage or current from
minimum to maximum value per unit of time is defined, as illustrated in the following
figures.
Time
Analog
Value
Output Update Time
Upper Limit
Lower Limit
m( Slope)
Time
Analog Value
m
m
m
Parameter
Description
Default
Output Update Time
The time unit is 10ms. By default this parameter is set to 0
(disabled). The maximum allowable setting is 3200 (32
seconds)
0

iR-AQ04-VI iR-AM06-VI iR-AI04-VI
12
Diagnose6.4
Analog Voltage Output
When voltage short circuit is detected, the module will generate an alarm and stop
output. An error code can be used to find out which channel is reporting error. (No
alarm will be generated when output is 0V)
Analog Voltage Output
When current open circuit is detected, the module will generate an alarm and stop
output. An error code can be used to find out which channel is reporting error. (No
alarm will be generated when output is 0mA)
Disconnection Detection
A channel alarm will be generated when input exceeds allowable range. In 1-5V /
4-20mA mode, disconnection can be detected when voltage is 0v or current is 0mA.
Analog Input –Fast Conversion Mode6.5
The conversion time per channel is 2ms. The total required conversion time is
calculated by multiplying 2ms by the number of channels, for example, 4 channels
will take 8ms for conversion. In fast conversion mode, where only one channel is
used, the conversion time can be reduced to 500us.
Fast Conversion Mode can be enabled by setting the corresponding register to 0.5ms.
Under this mode, only one channel can be used. If channel 0 is not closed, the rest of
the channels will not be able to perform conversion. If channel 0 is closed where

iR-AQ04-VI iR-AM06-VI iR-AI04-VI
13
channel 1 is opened, only channel 1 can perform conversion while the rest cannot.
Analog Input –Filter6.6
The built-in filter enhances signal precision to achieve better control. Setting a slower
conversion rate will get a better signal quality. By default the conversion time is 2ms.
Setting 50ms can effectively filter out noises in a 50/60Hz environment.
The filter can stabilize the signal by averaging sampled values, in order to achieve
better control.
7. Registers
Address
Description
Default
Read/Write
0
Analog
Output
Channel 0 Output Mode
1
Read/Write
1
Channel 1 Output Mode
1
Read/Write
2
Channel 2 Output Mode
1
Read/Write
3
Channel 3 Output Mode
1
Read/Write
4
Channel 0 Scale Range Upper Limit
32000
Read/Write
5
Channel 1 Scale Range Upper Limit
32000
Read/Write
6
Channel 2 Scale Range Upper Limit
32000
Read/Write
7
Channel 3 Scale Range Upper Limit
32000
Read/Write
8
Channel 0 Scale Range Lower Limit
-32000
Read/Write
9
Channel 1 Scale Range Lower Limit
-32000
Read/Write
10
Channel 2 Scale Range Lower Limit
-32000
Read/Write
11
Channel 3 Scale Range Lower Limit
-32000
Read/Write
12
Channel 0 Update Time
0
Read/Write
13
Channel 1 Update Time
0
Read/Write
14
Channel 2 Update Time
0
Read/Write
15
Channel 3 Update Time
0
Read/Write
16
Error Code
0
Read
17
Command
0
Read/Write
18
Channel Detection
FFh
Read/Write
19
Analog
Input
Conversion Time
0
Read/Write
20
Channel 0 Input Mode
1
Read/Write
21
Channel 1 Input Mode
1
Read/Write
22
Channel 2 Input t Mode
1
Read/Write
23
Channel 3 Input Mode
1
Read/Write
24
Channel 0 Scale Range Upper Limit
32000
Read/Write

iR-AQ04-VI iR-AM06-VI iR-AI04-VI
14
25
Channel 1 Scale Range Upper Limit
32000
Read/Write
26
Channel 2 Scale Range Upper Limit
32000
Read/Write
27
Channel 3 Scale Range Upper Limit
32000
Read/Write
28
Channel 0 Scale Range Lower Limit
-32000
Read/Write
29
Channel 1 Scale Range Lower Limit
-32000
Read/Write
30
Channel 2 Scale Range Lower Limit
-32000
Read/Write
31
Channel 3 Scale Range Lower Limit
-32000
Read/Write
32
Channel 0 Filter Frame Size
5
Read/Write
33
Channel 1Filter Frame Size
5
Read/Write
34
Channel 2 Filter Frame Size
5
Read/Write
35
Channel 3 Filter Frame Size
5
Read/Write
36
Channel 0 Maximum Value
0
Read
37
Channel 1 Maximum Value
0
Read
38
Channel 2 Maximum Value
0
Read
39
Channel 3 Maximum Value
0
Read
40
Channel 0 Minimum Value
0
Read
41
Channel 1 Minimum Value
0
Read
42
Channel 2 Minimum Value
0
Read
43
Channel 3 Minimum Value
0
Read
Analog Output Mode
Value
Mode
Resolution
0
Close Channel
N/A
1
-10V-10V(Default)
12bit
5mV
2
-5V-5V
11bit
5mV
3
1-5v
11bit
5mV
4
±20mA
12bit
0.01m
A
5
4-20mA
11bit
0.01m
A
Analog Input Mode
Value
Mode
Conversion Time
Resolution
0
Close Channel
N/A
N/A
1
-10V-10V(Default)
2ms
16bit
312uV
2
-5V-5V
2ms
16bit
156.25uV
3
1-5v
2ms
16bit
156.25uV

iR-AQ04-VI iR-AM06-VI iR-AI04-VI
15
4
±20mA
2ms
16bit
0.625uA
5
4-20mA
2ms
16bit
0.625uA
Analog Input Conversion Time
Value
Conversion Time
0
2ms
1 (Default)
2ms
2
5ms
3
10ms
4
15ms
5
25ms
6
60ms
7
0.5ms (Fast Conversion Mode)
When changing from one mode to another, the closest conversion time to 2ms x
number of channels will be set. Users can adjust the conversion time to get better
signal precision, for example, setting 50ms in 50/60Hz environment.
Scale Range Setting
Setting
Description
Default
Upper Limit
Allowable range: -32768~32767
32000
Lower Limit
Allowable range: -32768~32767
-32000
Please note that setting the upper limit and lower limit to the same value will make
the system use the default value.
Analog Output Update Time
Setting
Description
Default
Analog Output Update Time
Allowable range: 0~3200
Time unit: 10ms
By default this setting is disabled.
0
Analog Input - window size of digital filter
Setting
Description
Default
window size of digital
filter
Allowable range: 0~20
Setting value 0 will disable this
setting.
5
Analog Input maximum / minimum value
This setting keeps on recording the maximum and minimum digital value. The record

iR-AQ04-VI iR-AM06-VI iR-AI04-VI
16
can be cleared by giving a command (restart recording).
Setting
Description
Default
Input Max./Min. Value
Allowable range: -32768~32767
0
Error Code
Error Code
Description
0
Power error
1
Hardware error
2
Device isn't calibrated
3
Reserved
4
Conversion cannot be performed.
5-7
Reserved
8
Input Channel 0 error
9
Input Channel 1 error
10
Input Channel 2 error
11
Input Channel 3 error
12
Output Channel 0 error
13
Output Channel 1 error
14
Output Channel 2 error
15
Output Channel 3 error
Command
Value
Description
0x0001
Restore factory default
0x0002
Reset the max./min. value of analog output channel 0
0x0003
Reset the max./min. value of analog output channel 1
0x0004
Reset the max./min. value of analog output channel 2
0x0005
Reset the max./min. value of analog output channel 3
0x0006
Reset the max./min. value of analog output channel 0-3
Channel Detection
Bit
Description
Value
1
0
0
Analog Input Channel 0 Detection
Enable
Disable
1
Analog Input Channel 1 Detection
Enable
Disable
2
Analog Input Channel 2 Detection
Enable
Disable
3
Analog Input Channel 3 Detection
Enable
Disable

iR-AQ04-VI iR-AM06-VI iR-AI04-VI
17
4
Analog Output Channel 0 Detection
Enable
Disable
5
Analog Output Channel 1 Detection
Enable
Disable
6
Analog Output Channel 2 Detection
Enable
Disable
7
Analog Output Channel 3 Detection
Enable
Disable
8/15
Reserved

iR-AQ04-VI iR-AM06-VI iR-AI04-VI
18
8. iR-ETN Coupler Address Mapping
Module No.
Module Address
iR-ETN Modbus Address
1st
0-500
20000-20499
2nd
0-500
20500-20999
3rd
0-500
21000-21499
4th
0-500
21500-21999
……
……
……
16th
0-500
27500-27999
Example:
Module
Module Register
iR-ETN Modbus Address
iR-AQ04-VI
0# Channel 0 Output Mode
20000
1# Channel 1 Output Mode
20001
2# Channel 2 Output Mode
20002
3# Channel 3 Output Mode
20003
………
……..
16# Error Code
20016
iR-AI04-VI
20# Channel 0 Input Mode
20520
21# Channel 1 Input Mode
20521
22# Channel 2 Input Mode
20522
23# Channel 3 Input Mode
20523
………
……..
iR-AM06-VI
0# Channel 0 Output Mode
21500
1# Channel 1 Output Mode
21501
………
……..
20# Channel 0 Input Mode
21520
Module No.
Module Name
0
iR-ETN
1
iR-AQ04-VI
2
iR-AI04-VI
3
iR-DQ16-P
4
iR-AM06-VI