Well TVS-MON-SWD32-WL User manual

INSTRUCTION MANUAL
MONITOR DESK MOUNT
Thank you for choosing WELL. Please read carefully the following instructions and keep them
within reach.
Reorder No: TVS-MON-SWD32-WL

UNPACKING INSTRUCTIONS
Carefully open the carton, remove contents and lay out on cardboard or other protective surface
to avoid damage.
Check package contents against the Supplied Parts List in the next page to assure that all
components we received undamaged. Do not use damaged or defective parts.
Carefully read all instructions before attempting installation.
IMPORTANT SAFETY INFORMATION
Install and operate this device with care. Please read this instruction before installation, and
carefully follow all instructions contained. Use proper safety equipment during installation.
Please call a qualified installation contractor for help if you don’t understand these directions or
have any doubts about the safety of the installation.
Do not use this product for any purpose or in any configuration not explicitly specified in this
instruction. We disclaim any and all liability for injury or damage arising from incorrect
assembly, incorrect mounting, or incorrect use of this product.
Supplied Parts List
CAUTION
This monitor desktop mount must be securely attached to the horizontal desk. If the mount is not
properly installed it may fall, resulting in possible injury and/or damage.
STEP 1. Install the Pole to the Desktop
Option A: Desk Clamp Install
1. Remove the 3pcs M5X20 bolts at the bottom of the pole (a) with hex key, see Figure 1A.
2. Install the clamp brace (c) to the pole (a) using 3pcs M5x20 Bolts, and tighten using the hex
key (E), see Figure 1.

3. Install the “c’-Clamp (b) to the pole assembly according to the thickness of the desktop.
The thickness can be changed of three positions. Connect it using 2 pcs M8x12 Bolts (A), and
tighten using the hex key (E).
Tighten the “c’-Clamp to the desktop by twisting the plastic knob, see Figure 2.
Option A: Base Install
Self Drilled Hole Installation
Position the Pole(a) on the mounting surface and mark the center hole. Drill a 3/8” (10mm)
diameter hole at the marked position through the mounting surface.
1. Remove the 3pcs M5X20 bolts at the bottom of the pole(a) with hex key, see Figure1A.
2. Install the Base Plate (f) to the Pole(a) using 3 pcs M5x20 Bolts, and tighten using the hex key
(E), see Figure 5.
3. Use screwdriver counter-clockwise release the screw, and counter-clockwise release the plastic
knob. see Figure 5A.
4. Position the Pole (a) on the mounting surface and secure using the Support Plate (B), see
Figure 6.

Option B: Base Install
Existing Hole Installation
If the existing grommet hole comes with a plastic protector, remove it to ensure a flat surface
before installing the desk mount.
1. Remove the 3pcs M5X20 bolts at the bottom of the pole (a) with hex key, see Figure A.
2. Install the Grommet Base Plate (f) to the Pole (a) using 3 pcs M5x20Bolts, and tighten using
the hex key (E), see Figure 3.
3. Use screwdriver counter-clockwise release the screw, and counter-clockwise release the plastic
knob. see figure 3A
4. Position the Pole(a) on the mounting surface and secure using the Support Plate (B), see
Figure 4.
STEP 2. Install Arm to the Pole

STEP 3. Attach the VESA plate to the monitor
STEP 4. Slide the monitor to the head of swivel arm
STEP 5. Make the necessary adjustments

STEP 6. Manage the wires and store the keys on wire clip
Waste electrical and electronic equipment are a special waste category,
collection, storage, transport, treatment and recycling are important
because they can avoid environmental pollution and are harmful to
health. Submitting waste electrical and electronic equipment to special
collection centers makes the waste to be recycled properly and protecting
the environment. Do not forget! Each electric appliance that arrives at the
landfill, the field, pollutes the environment!
Importer & distributor:
SC VITACOM ELECTRONICS SRL
CIF: RO 214527
Tel. [phone]*
of[email protected], www.vitacom.ro