Wincomm WPC-651 User manual

WPC-651
Single VIA Eden Processor
Micro PC
User’s Manual
P/N: 205-000WPC6510, Version:V1.1
WINCOMM TECHNOLOGY CORP.
Address:3F, No.14 , Prosperity Rd. II, Science-Based Industry Park,
Hsinchu, Taiwan, 300
Tel: [phone]
Fax: [phone]
Web Site: http://www.wincomm.com.tw/
Copyright© Aug., 2003. All rights reserved
All other brand names are registered trademarks of their respective owners.

Copyright Notice
Copyright © 2003 by Wincomm Technology Corp.
All Rights Reserved.
Printed in Taiwan.
This publication is protected by copyright and all rights are reserved. No part or
whole of it may be reproduced or transmitted in any form or by any means,
electronic or mechanical, including photocopying and recording without prior
consent of Wincomm TECHNOLOGY CORP.
The information in this document has been carefully checked and is believed to be
accurate. However, Wincomm TECHNOLOGY CORP. assumes no responsibility
for any errors that may appear in this document. The material contained herein is
for informational purposes only.
The information contained in this document is subject to change without any
notices.
Acknowledgments
All product names or trademarks are properties of their respective owners.

III
ΰTo
Be
Addedα

4
Chapter 1 System Overview......................................................... 1-1
1.1 Introduction .............................................................................................1-1
1.2 Features ...................................................................................................1-1
1.3 System Specification ...............................................................................1-3
1.4 System View............................................................................................1-5
1.4.1 Product Outlook ..............................................................1-5
1.4.2 Outline Drawing..............................................................1-7
1.4.3 I/O connectors List..........................................................1-8
1.5 Unpacking ...............................................................................................1-9
Chapter 2 Getting Started............................................................ 2-1
2.1 Setting Up the System .............................................................................2-1
2.2 Using a Compact Flash Memory Card ....................................................2-2
2.3 Using PCMCIA Module..........................................................................2-4
Chapter 3 BIOS Setup Information ............................................ 3-1
3.1 Entering Setup .........................................................................................3-1
3.2 Main Menu ..............................................................................................3-3
3.3 Standard CMOS Setup Menu ..................................................................3-4
3.4 Standard CMOS Setup Menu ..................................................................3-9
3.5 Advanced CMOS Setup Menu ................................................................3-9
3.6 Advanced Chipset Setup Menu .............................................................3-11
3.7 Power Management Setup Menu...........................................................3-14
3.8 PCI/Plug and Play Setup .......................................................................3-15
3.9 Peripheral Setup ....................................................................................3-17
3.10 Hardware Monitor Setup .....................................................................3-20
3.11 BIOS POST Check Point List..............................................................3-20
3.12 Flash BIOS Utility...............................................................................3-25

5
J
umper
L
oca
ti
on................................................................................................
I
Jumper Setting................................................................................................. II
Jumper NotesII
Jumper Setting................................................................................................ III
Connector Definitions ....................................................................................VI
Connectors Location...............................................................................VI
Connectors List..................................................................................... VII
Battery Installation ..............................................................................XIX
Appendix B. System Assembly Reference................................. XXI

6
How to Use This Manual
This manual is written for the system integrator, PC technician and
knowledgeable PC end user. It describes how to configure your WPC-651 SERIES
to meet various operating requirements. The user’s manual is divided into four
chapters, with each chapter addressing a basic concept and operation of the server
board.
Chapter 1: Introduction - presents what you have inside the box and gives
you an overview of the product specifications and basic system architecture for
the WPC-651 SERIES Micro PC. And also shows the connectors of WPC-651
so that you can easily configure your system.
Chapter 2: Getting Started - shows you how to set up the system and
introduce how to use PCMCIA and Compact Flash slots.
Chapter 3: BIOS Setup Information - specifies the meaning of each setup
parameter, how to get advanced BIOS performance and update to a new BIOS.
Additionally, the POST checkpoint list will give you a guide for
troubleshooting.
The contents of this manual are subject to change without prior notice. These
changes will be incorporated in new editions of this manual. We may make
supplements or changes for the product described in this manual at any time.

1-1
py
1.1 Introduction
Wincomm’s Micro PC, WPC-651, is especially developed for embedded
application. WPC-651 series are based-on the features of compact size, high
performance, cost-effective and truly low power solution with VIA Eden series
platform. This slim system is ideal used in all harsh environments, such as high
temperature, high pressure or any anxiously for reliable and stable situations but
concern spaces. Surely this compact design is without sacrificing the performance
and functionality.
WPC-651 series can support CRT output as SXGA+, UXGA and UXGA+ for
high resolution. This is very suitable for commercial KIOSK, Point-of-Information
and Point-of-Sales application. Its 10/100 Base-T Ethernet allows the heavy
network assignment in a fast and stable manner.
WPC-651 provides the standard I/O features like the main stream PC
including Compact Flash Interface, two serial ports, one parallel port, two USB
ports, audio ports for line-in/line-out/mic-in, one PS/2 port to support Mouse and
Keyboard via Y-cable, Reset/Power-on switch and Power-on/HDD/LAN
indicators.
WPC-651 provides one PCMCIA interface for 16-bit PCMCIA module or
ATA flash memory module. This feature can support some application such as
Wireless LAN, GPS and so on.
WPC-651 series are rugged with aluminum-packed chassis, and the compact
size for 170x150x66mm is easy to develop for various appliances, such as
information collecting machine in Factory Automation, home-PC, mobile
application, medical facilities and any other computing equipment in today’s
unrestrained technical field.
1.2 Features
The WPC-651 features:

1-2
VIA
Ed
en
400MH
z
(WPC
-
651
-
P400
ser
i
es
)
w
ith
i
n
t
erna
l
FANLESS
thermal solution
VIA C3 Low Voltage 1GHz (WPC-651-P1000 series) with
Wincomm’s proprietary thermal solution
System Memory
128/256 MB system RAM, maximum to 512 MB
Mass Storage Device
One 2.5-inch IDE hard disk drive
Compact Flash Memory Support
One Compact Flash slot, support Compact Flash memory card
PCMCIA interface
One PCMCIA slot, support 16-bit PCMCIA module and ATA flash
memory module with hot-swapping function
Video Function
VGA display controller with AGP4X enhanced 2D and 3D graphics,
display memory dynamic sharing with system memory (up to 32MB)
Audio Function
Dual full-duplex Direct Sound channel between system memory and
AC97 link, standard AC97 codec interface with Line-in, Line-out and
Microphone-in ports
Ethernet Function
10/100Base-T Ethernet bus

1-3
AMI
BIOS
,
2
MB
Fl
as
h
EEPROM
,
Pl
ug-an
d
-
Pl
ay compa
tibl
e
Watchdog Function
1~63 seconds, software programmable
1.3 System Specification
NOTE: Specifications are subject to change without notice.
Parts Specifications
CPU VIA Eden 400MHz processor onboard or VIA C3
Low Voltage 1GHz processor onboard
Other VIA EBGA-type processors can be requested
by OEM model
System
memory
144-pin DIMM socket supporting PC100/133
64/128/256/512 MB SDRAM
CPU Board:
WEB-6580
I/O
interfaces
CRT port
RS-232C port (COM1)
RS-232C/422/485 port (COM2)
SPP/EPP/ECP parallel port
PS/2 keyboard/mouse port
10/100 Base-T LAN connector
Compact Flash Interface
PCMCIA
Slot:
WTB-PCMCI
A
PC-104
Peripheral
module
Comply with PCMCIA V.2.10 and JEIDA 4.1
specification
Support each slot accept type II card
16-bit data bus
Support Read/Write Flash card with Hot-swapping
function
USB and
Audio
Connectors:
WTB-A01
Peripheral
module
Two USB 1.1 ports
Microphone input connector
Line input connector
Line output connector

1-4
Output
power
60W
AC-to-DC
Power
Adapter Input
voltage
100 a240 V, 47~63 Hz, 1.9A
Power Output
voltage
Output Maximum Load
+5 V 7 A
+12 V 3 A
Dimension 170×150×66 mm (LxWxH)
Weight 3.0 Kg (net), 4.5Kg (gross)
Temperature Operating: 0 qCa40 qC
Storage: –20 qCa60 qC
Environment
Humidity 5% a90% @ RH, non-condensing

1-5
y
1.4.1 Product Outlook
The front view of WPC-651-P400
The front view of WPC-651-P1000

1-6
The rear view of WPC-651-P400
The rear view of WPC-651-P400

1-7

1-8
˄ ˅ ˆ ˇ
ˈ
Front Panel
ˉ
ˌˋˊ ˄˃
Rear Panel
˄˄ ˄˅ ˄ˆ
Ref Component Ref Component
Audio for Line-in, Line-out, Mic-in CRT output
Serial port for RS-232 Serial port for RS-232/422/485
USB 1.1 ports Compact Flash slot
Power-on and HDD LEDs RJ45 for Ethernet
LPT port PCMCIA slot
Power-on Switch DC-in for power input
PS/2 Keyboard and Mouse
˄ ˋ
˅ ˌ
ˆ˄˃
ˇ˄˄
ˈ˄˅
ˉ˄ˆ
ˊ

1-9
After unpacking the shipping carton, you should find these standard items:
The WPC-651 Micro PC
Accessory box:
– Power cord cable
– AC-DC Adapter
– Y-cable for PS/2 Keyboard and Mouse
– System Driver, Utility and User Manual CD-title
– Quick installation Guide
– Fixed Brackets
Inspect all the items. If any item is damaged or missing, notify your dealer
immediately.

2-1
pg
This chapter tells you how to set up the system.
2.1 Setting Up the System
The following is a summary of the steps in setting up the system for use.
CAUTION: Make sure that power to the system and each of the devices to be
connected is switched OFF before plugging in the connectors.
1. Make any required external connections such as the display, keyboard, and
mouse.
2. Plug the appropriate end of the power cord into the power connector of
AC-to-DC Adapter and plug the other end-side to DC Power-in connector of
the on the rear of the system. Then plug the other end of the power cord to an
electrical outlet.
3. Press the power switch on the front of the system to turn on the system’s
power.
4. If necessary, run the BIOS SETUP program to configure the system (see
Chapter 3).
5. Install the software drivers if necessary.

2-2
gp y
To insert a Compact Flash Memory Card, please follow the blowing steps.
1. Locate the Compact Flash Memory Card slot on the rear of the system.
2. Slide the Compact Flash Memory Card into the slot until the eject button
pops out and push the eject button to the left side until closed to the stick.

2-3
3. When a new card is seated, the system may detect it and try to install the
appropriate driver. Follow the onscreen instruction to complete the
process.
To remove a Compact Flash Memory Card:
1. Please turn off the system before you remove the Compact Flash Memory
Card.
2. Move the eject button from the stick.
3. Push the eject button and the card will slide out slightly.
4. Pull the card out of the slot.
Note:
Not support hot swap mode. Please turn off the system while you plug or
remove the compact flash module.

2-4
g
To insert a PCMCIA module, please follow the blowing steps.
1. Locate the Compact Flash Memory Card slot on the rear of the system.

2-5
2. Slide the PCMCIA module into the slot until to the bottom of the slot.
3. When a new card is seated, the system may detect it and try to install the
appropriate driver. Follow the onscreen instruction to complete the
process.
To remove the PCMCIA module,
1. Please push the button on the right side of the slot and the button will be
pop-up.
2. Pull the card out of the slot.