Wirepath ONE WP-ONE-DOOR Series User manual

Thank you for purchasing a premium product from Wirepath
Structured Wiring. The Wirepath ONE™ Media Door is designed to
provide serious exibility for a professional installation.
Wirepath ONE™ Door
A
B
C
D
E
F
G
H
A - Surface Mounting
Mount the door to a surface, no tricky leveling. Reverse the swing of the door prior to
installation if desired. See back for installation steps.
B - Router Friendly Construction
Made from durable UL Listed ABS plastic to ensure that there is little signal
interference when using routers or other wireless devices.
C - Mounting Platform
The platform allows for a exible conguration. Flip the platform over to raise or lower
the height. Additionally, the xed standoffs allow the platform to swing left or right.
D - Wire Guides
Manage your wires by routing through the wire
guides on the side of the platform.
E - Module Attachment Holes
Secure modules with pins or zip ties.
F - Lock & Key
Each door comes equipped with a pre-installed lock and 2 keys to keep prying hands
away from equipment inside the enclosure.
G - Plexiglass Window
View the status of a device through the plexiglass window without having to remember
to grab the key.
H - Venting and Trunk Line Management
Ventilation is huge. We’ve already accounted for that with open vents in the bottom
and top of the door. Additionally, you may run thick trunk lines through the open vents.
I - Media Enclosure Shelves (not included/shown)
Place shelves (WP-ONE-ENCL-SHELF) wherever you want! The shelves can be
mounted on the Mounting Platform on the inside of the door where space is available.
If mounting the shelf to a platform, as opposed to the module attachment holes, you
may need to press in the center hook to attach it properly.
J - Cross-compatible
All same-size Wirepath Enclosure cans are compatible with this surface mounted
door.
www.snapav.com Support: 866.838.5052

Limited Lifetime Warranty
This Wirepath Product has a Lifetime Limited Warranty. This warranty includes parts and labor repairs on all components found to be defective in
material or workmanship under normal conditions of use. This warranty shall not apply to products that have been abused, modied, or disassembled.
Products to be repaired under this warranty must be returned to SnapAV or a designated service center with prior notication and an assigned return
authorization number (RA).
Lifetime
WP-ONE-DOOR-XX
Dimensions
14 17.91"W x 15.96"H x 2.94"D
20 17.91"W x 21.96"H x 2.94"D
28 17.91"W x 29.96"H x 2.94"D
40 17.91"W x 41.96"H x 2.94"D
Hardware Pack 1
2-Position Mounting Platform
14 1
20 1
28 1
40 2
Material White ABS Textured Plastic
Dual Locking Yes
UL Listed Material 94V-0
Installation
Tools Needed:
5mm Allen Wrench #2 Phillips Screwdriver
1. Locate the desired position over the installed enclosure, leaving enough clearance for the door to swing
open in the desired direction. To reverse the swing direction, skip to Swing Direction Reversal below
prior to installation.
2. To mount, remove the door rst. Unlatch and swing the door open before pulling upward to remove.
3. Ensure the door base is level, and drive a minimum of 4 (14”, 20”), or 6 screws (28”, 40”) into the drywall
or plywood through the Surface Mounting Holes of the door base.
4. Reinsert the door’s hinges onto the hinge pins, orienting it to swing in the desired direction. To reverse
the default direction, follow the directions below.
Swing Direction Reversal
ATTENTION: For best practice, determine the direction you would prefer the door to swing prior to installation.
Reversing the hinges requires access to the rear of the door base.
1. Open the door, then slide it up and off all hinges.
Size 14 in. 20 in. 28 in. 40 in.
No. of Hinges 2 2 3 4
2. Remove hinge bolts from the rear of the door base with a 5mm Allen Wrench. Turn the hinges laterally
so that the hinge pins face the outside of the enclosure.
3. Remove the two screws from the hinge pin receiver bracket on the door with a screwdriver. Swap the
hinge pin receiver over to the adjacent slot.
4. Slide the door back onto the hinges. Continue on to reverse the direction of the latch.
Latch Reversal
1. To remove the door latch (F), remove the clamp with a #2 Phillips screwdriver, and slide the latch out
of the door.
2. Rotate the latch mechanism 180° and re-install into latch opening.
3. Loosen the latch plate screw, located behind the latch, and rotate the latch 180° so that it faces the slot
in the door. Tighten screw back down once it is in the correct position.
Rev: 141212-1400www.snapav.com Support: 866.838.5052
Front Rear