Workrite Workrite Poise–Dual User manual

Workrite Poise™–Dual
Assembly Instructions
Clamp and Grommet Mounts

2
Workrite Poise–Dual™ Installation Instructions
Important Safety Instructions
Read and understand all these safety
instructions before using this product.
Do not mount the clamp base or the grommet base on an unstable surface
(any surface that will not hold the base rmly).
For safety reasons, the internal gas-strut of the Workrite Poise–Dual™ is
pre-adjusted at the factory to the lowest force for the prevention of arm
body recoil during installation.
IMPORTANT SAFETY PRECAUTION:
During installation, beware that the arm body can move suddenly when
attaching or detaching the LCD monitor to the arm. WHEN CHANGING
THE LCD MONITOR, ALWAYS RE-ADJUST THE GAS STRUT TO THE LOWEST
FORCE SETTING. Without this adjustment, the arm will move suddenly up-
ward when the monitor is removed.
Do not attempt to disassemble, service or modify the product yourself.
Use only a slightly damp cloth to clean the arm surface. Never use am-
mable solvents like alcohol, benzene, thinner, etc.
Table of Contents
List of Parts .................................................................................................. 3
Step 1: Verify that you have all the hardware and tools needed for the assembly ... 4
Step 2: Attach Clamp Base to Work Surface ...................................................... 4
Step 3: Attach Grommet Base to Work Surface.................................................. 5
Step 4: Attach Monitor Arms to Monitors .......................................................... 5
Step 5: Attach Pivot Base and Arms ................................................................. 6
Step 6: Vertical Movement Adjustment ............................................................. 7
Step 7: Ball-joint Adjustment for Tilt Action ...................................................... 7
Step 8: Final Touches: Cable Management ........................................................ 8
Replacement Part Numbers............................................................................. 8

3
Workrite Poise–Dual™ Installation Instructions
List of Parts, grouped by carton
HU-Bracket
Qty: 1
JM8 X 1.25 X
130mm Thread Rod
Qty: 1
PDual Mount Clamp Qty: 1
GGrommet Base Qty: 1
AClamp Base Qty: 1
N14" Pole Qty: 1
QPlastic Spacer 30mm
OD, 18.5 mm ID
Qty: 2
OCable manager hook and loop strips
Qty: 2
UM8 Disc Spring
Washer 23mm OD,
8.2 mm ID
Qty: 2
SButton-head Cap Threaded Bolt M8 X
1.25 X 70mm
Qty: 2
BClamping Bracket Qty: 1
CBase Cushion Qty: 1 DM5 Hex Wrench
Qty: 1
EM2.5 Hex Wrench Qty: 1 FButton head cap screw M8 X 1.25 X 15mm
Qty: 2
IM8 Washer Qty: 2
CBase Cushion Qty: 1
DM5 Hex Wrench Qty: 1 EM2.5 Hex Wrench
Qty: 1
KM8 X 1.25 Wing Nut
Qty: 2
RPivot Pins 55mm Qty: 2
VFlat M8 Washer
16mm OD
Qty: 2
TSet Screws M5 X .8 X 10mm
Qty: 2
YRound-head screw M4 X 0.7 X 10mm
Qty: 8*
WAssembled Arm Qty: 2*
ZRound-head screw M4 X 0.7 X 6mm
Qty: 8*
XEnd Cap Qty: 2*
aPlastic Holding Tabs Qty: 16*
* Note that there are two of these cartons.
Quantities given show total from both cartons.
OR
For model #: PA2000-C-_
For model #: PA2000-G-_
LButton head bolt M8 X 1.25 X 65mm
Qty: 1 MM4 Hex Wrench
Qty: 1

4
Workrite Poise–Dual™ Installation Instructions
1Verify that you have all the hardware and tools needed for the assembly
Check your cartons against the list on page 3 to verify that you have all the parts needed.
You will also need the following tools:
#3 tip Phillips screwdriver
2
For Grommet Base please skip to Step 3.
Attach the base cushion to the underside of the
base.
Attach 14” pole to base, securely tighten 4 set
screws (already in place).
Attach the clamping bracket to worksurface with 2
button-head cap screws. (See note below.) Use the
upper set of holes on the bracket for work surfaces
between ½" and 1¼" thick, and use the lower set for
work surfaces between 1¼" and 2¼" thick.
Tighten the clamping bracket until it is rmly
clamped to the work
surface.
Skip to step 4.
If there is not enough clearance to t the assembled base between
the back of the worksurface and the wall, place the clamp base on the
desk edge before attaching the clamping bracket from below.
C
B
E
F
a
b
c
d
a
b
c
d
A
Clamp Base Only: Attach Clamp Base to Worksurface
N

5
Workrite Poise–Dual™ Installation Instructions
4
3
Attach Monitor Arms to Monitors
Place monitor carefully on a clean, at
surface, face down.
Attach the monitor arm to the back of the
monitor with four screws, using a Phillips-
head screwdriver (not included). Use the
mounting screws provided by your moni-
tor manufacturer if available. Otherwise,
use the screws provided that best ts
your monitor.
Use the outer holes for a
100mm mount, or the inner holdes for a
75mm mount.
Repeat for the second monitor.
W
Y or Z
Remove the center hole from the base cushion,
then attach it to the underside of the base, aligning
the hole in the base with the hole in the protector.
Thread the M8 Thread Rod into the bottom of the
base. Use the M4 Allen wrench to tighten if needed.
Attach 14" pole to base, securely tighten 4 set
screws (already in place).
Place the base on the work surface, centering it over
a bolting hole from ⅜" to 3" in diameter.
Position the U-Bracket and Small Washer onto the
M8 Thread Rod and secure the bracket by tightening
the Wing Nut.
To provide extra stability, especially for monitors
over 15 lbs., install additional stabilizing Button
Head Bolt. Follow appropriate instruction based on
mounting option chosen:
- For mounting holes larger than 1¾", thread the
65mm Button Head Bolt through the small hole in
the back of the base, and through the second hole in
the U-Bracket securing with the second Washer and
Wing Nut.
- For mounting holes smaller than 1¾”, drill a second
hole for the Button Head Bolt behind the center
bolting hole. The two holes must be at least ⅜" each
in diameter, and their centers should be 1⅜" apart.
The Button Head Bolt should be positioned at the
back of the Grommet Base.
Proceed to step 4.
1) Single hole:
3"ø max, 1¾"ø min
2) Two holes:
Min: ⅜"ø
1⅜"
Mounting Diagram
Select one of two mounting options:
Single hole or Two holes.
Rear edge of worksurface
Grommet Base Only: Attach Grommet Base to Work Surface
a
b
c
d
a
b
c
d
N
EG
I
J
H
K
C
ee
L

6
Workrite Poise–Dual™ Installation Instructions
Attach Pivot Base and Arms
Place the pivot pins and the large plastic spacers onto the dual mount clamp.
Place the dual mount clamp assembly onto the pole with the ratchet handle facing the back. Posi-
tion the mount so that the top of it is approximately 7” from the desk for a 15” monitor, 8” for a
17” monitor or 9” for a 19” monitor. Tighten the dual mount using the ratcheting handle. Pull the
handle out to release and rotate to allow for additional turns to tighten.
Attach one assembled monitor arm to the dual mount clamp. Position the arm horizontally and test
the height range to be sure it is correct for your monitor. If not, remove the arm and move the dual
mount clamp accordingly. Then replace the arm. Attach the second arm to the dual mount clamp.
Secure the monitor arms by placing the small at washer on the 70mm threaded bolt, followed by
the larger disc spring washer, with the concave side facing away from the bolt head (down), and
then placing the bolt with the washers into the hole on the end of the monitor arm, tightening with
the M5 hex wrench. Tighten to a light friction so that the arm can turn, but not too loosely.
Install and tighten the set screws in the dual mount with the M2.5 hex wrench to lock the 70mm
bolts.
Press the end caps onto the ends of the monitor arms, covering the 70mm bolts.
5
Remove the monitor arms before
adjusting the clamp height to avoid
scratching the nish of the pole.
a
b
c
d
e
f
a
b
c
d
e
f
R
W
Q
S
T
P
V
U
X

7
Workrite Poise–Dual™ Installation Instructions
7
6
Adjustment for Tilt Action
If the monitor doesn’t hold its tilt position or
is too hard to tilt, adjust the screw directly
behind the LCD screen with the M5 Allen
wrench provided (clockwise to tighten,
counter-clockwise to loosen).
If your monitor is too light or too heavy for the factory-set tension,
the arm will raise or lower too easily (or even on its own). If this is the
case, you need to adjust the vertical movement.
Set the monitor arm at a 90° angle and locate the adjustment screw on
the top of the arm joint.
If the arm tends to rise, turn the adjustment screw clockwise using
the M5 hex wrench, loosening until the arm reaches a stable, balanced
adjustment.
If the arm tends to drop, turn the adjustment screw counterclockwise
using the M5 hex wrench, tightening until the arm reaches a stable, bal-
anced adjustment. With too much tension on the arm, the arm will tend
to rise.
Vertical Movement Adjustment
a
b
c
Loosen
Tighten
Tension
screw
90°
To prevent damage to the arm,
remove the hex wrench after
adjustment.
Adjustment
Screw
a
b
c

8
Workrite Poise–Dual™ Installation Instructions
Secure attached hook and loop strips around monitor
cables, again leaving enough slack at both ends of the
arm for full movement of the arms.
Attach the monitor cables to the pole and secure with
provided hook and loop straps, again leaving enough
slack between the extension arm and the pole for full
movement of the arm.
Final Touches: Cable Management
Thread monitor cables through Cable Mount located on underside of Forearm.
Place Holding Tabs in center slot as shown and slide into place along Mount track. Use four tabs on
each side.
8
a
b
c
Workrite
Ergonomics
Strip
Strip
a
O
a
b
c
6400443: Poise Arm W/O Base Type 1/5-15 Lb Graphite
6400441: Poise Arm W/O Base Type 1/5-15 Lb Silver
6400444: Poise Arm W/O Base Type 2/10-22 Lb Graphite
6400442: Poise Arm W/O Base Type 2/10-22 Lb Silver
6400364: Dual Arm Pole Mount – Graphite
6400363: Dual Arm Pole Mount – Silver
SASP-B: Pole 14” W/Cover Cap – Black
6400365: Pole 14” W/Cover Cap – Silver
SACB-B: SA Clamp Base Kit, Graphite
SACB-S: SA Clamp Base Kit, Silver
SAGB-B: SA Grommet Base Kit, Graphite
SAGB-S: SA Grommet Base Kit, Silver
Replacement Part Numbers