Griffin Technology AP3372 User manual

www.Griffin-Stands.com
Speaker Wall
Mount
Brackets
www.Griffin-Stands.com
www.Griffin-Stands.com
Griffin™ stands and accessories are manufactured
in several innovative factories responsible for
developing products that address the newest
needs and trends of the current market. We take
pride in the Griffin™ brand and endeavor to be on
the forefront of the musical stands and musical
and lighting accessories market.
Performance Issue, Uneven or Unstable- Make
sure all nuts and bolts are tight on the product. If they
are, then loosen all nuts and bolts 1 full turn counter-
clockwise, then go back and tighten each bolt only ½
turn tight. Then do a final tighten turn for another ½
turn tight. Next, Make sure there are not any missing
nuts or bolts. Third, ensure all parts on the product
are not broken or defective. Finally, Re-read the
assembly instructions or watch the product
demonstration video to ensure you have correctly
assembled or are using the product properly with
factory specifications.
Missing Parts- The pictures, videos and images
shown in this manual might have changed style or
count due to the product being redesigned. So in rare
cases the part may no longer be included or of a
different style. However, if you think you are missing
a part that is necessary to the assembly and use of
your product, then first carefully double check all
packaging for any parts you think are missing. Some
parts might be hiding in the packaging or loose in an
inner box.
User Manual
M o d e l # A P 3 3 7 2
Griffin | 11408 Hwy 64 W, Tyler, TX 75704 |
[email protected] | www.Griffin-
Stands.com
For current product specifications, please to go
www.griffin-stands.com and type the model number
into the search bar. Locate the product listing to view
the current factory specifications. Thank you for purchasing the Griffin Speaker Wall
Mount Brackets. Your product comes with a 1 year
factory warranty from purchase date. Please read all
assembly instructions prior to assembling your new
cart. Pictures that may aid in assembly can be found
by going to www.griffin-stands.com and typing
AP3372 into the search bar.

Step 4 –Drill into the marked holes and insert the
threaded plastic anchors to each hole, a hammer might
be needed to insert these.
Step 7 –For safety
reasons, please always
make sure to test the
stability and safety of
the product before
use. Double check all
nuts and bolts, knobs
and connectors, make
sure that these are
tight and securely
fastened before use of
your product. Test the
product under light use
or light loads the first
time to confirm
assembly and structure
of the product is
correct.
Step 1 - Align the two tilt adjustment arms and insert
the top arm into the bottom arm and insert the pin
into one of the holes. The amount of tilt that you want
determines which hole to insert the pin into, please
see Figure 1.
Step 2 –As shown in
Figure 2, the speaker
post mount is screwed
in one of the 3
different holes on the
adjacent steel bar. It
depends on your
preference to where
you would want the
mount to be screwed
in. You may use a
wrench to counter the
bolt while tightening
the speaker post
mount.
Step 3 –To mount the bracket to the wall, take the
bracket and measure the height if it suits your
preference. Mark the holes to where you should drill to
mount the brackets. Make sure that everything is
leveled to avoid the bracket leaning on one side and
making it a risk for your items to fall. See Figure 3.
Step 5 –Take the bracket and mount it on the wall, align
each hole on the wall to the brackets. Screw in first one
at the top and one at the bottom (do not tighten
immediately). Next is insert all the other screws in the
holes and adjust the tightness of each screw one by one,
this is to make sure that one side is not over tightened
and the brackets will be leaning over to one side.
Please scan the QR Code below for the product
demonstration video. Or go to the URl shown here and find
the product video. www.Griffin-Stands.com/Videos
Step 6 –The loop on
the side is used to
insert the cables to be
connected to the back
of the speakers. (See
Figure 4).
Always check the integrity of the speaker wall mount
bracket before mounting anything. You may hold onto
the speaker post mount and grip it tightly and wiggle the
brackets to test.