Wyrestorm NHD-000-RACK4 User manual

The NHD-000-RACK4 is a 6U rack mount that provides a clean installation for up to 12 NetworkHDTM 100, 200 and 400 Series encoders and decoders,
NetworkHD Controller and Enado Mini.
WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features before beginning the installation
process.
In the Box
1x NHD-000-RACK4 Chassis
2x 19” Rack Mounting Bracket
7x Blank Plate
1x Assembly Screws Pack
Dimensions and Weight
Dimensions and Weight
Rack Units/Wall Box 6U
Height With | Without Feet 265.9mm/10.47in | 265.9mm/10.47in
Width With | Without Brackets 483mm/19.02in | 440mm/17.33in
Depth With | Without Handles 188.3mm/7.42in | 150mm/5.91in
Weight (Chassis without Plates) 2.3kg/5.06lbs
Installing Chassis in a Rack
1. Attach the rack ears to both sides of the chassis using the supplied screws.
2. Position and install the assembly into the rack and secure with rack screws
(not supplied).
Tip: To keep the installed devices within operating temperature, do not
position the NHD-000-RACK4 directly above heat generating devices such as
ampliers.
Installing Devices into the Chassis
1. Install the devices into the chassis using the supplied screws and
mounting plates.
2. Install the supplied blank plates using the supplied screws to cover any
open slots in the chassis.
3. If not installing in a rack, place the assembled chassis on a solid at
surface such as a cabinet or shelf located in a dry, well ventilated area.
4. Connect the devices per their specic documentation.
Note: WyreStorm reserves the right to change product specication, appearance or dimensions of this product at any time without prior notice.
Copyright © 2018 WyreStorm Technologies | wyrestorm.com
NHD-000-RACK4 Quickstart Guide | 180718
UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)
6U/12 Slot Rack Mount for NetworkHD™ 100/200/400 Series
Quickstart Guide
NHD-000-RACK4

The NHD-000-RACK3 is a 7U rack mount that provides a clean installation for up to 8 NetworkHD™ 600 series encoders. Mounting brackets for NHD-000-CTL
NetworkHD controller are also included allowing for all required devices to be installed in a single location.
WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features before beginning the installation
process.
In the Box
1x NHD-000-RACK3 Chassis
2x 19” Rack Mounting Bracket
8x NetworkHD 600 Series Encoder/Decoder Mounting Plate
1x NHD-000-CTL Controller Mounting Plate
4x Blank Plate
1x Assembly Screws Pack
Dimensions and Weight
Dimensions and Weight
Rack Units/Wall Box 7U
Height With | Without Feet 310.3mm/12.22in | 310.3mm/12.22in
Width With | Without Brackets 483mm/19.02in | 440mm/17.33in
Depth With | Without Handles 188mm/7.41in | 160.7mm/6.33in
Weight (Chassis without Plates) 4.5kg/9.9lbs
Installing Chassis in a Rack
1. Attach the rack ears to both sides of the chassis using the supplied screws.
2. Position and install the assembly into the rack and secure with rack screws
(not supplied).
Tip: To keep the installed devices within operating temperature, do not
position the NHD-000-RACK directly above heat generating devices such as
ampliers.
Installing Devices into the Chassis
1. Install the devices into the chassis using the supplied screws and
mounting plates.
2. Install the supplied blank plates using the supplied screws to cover any
open slots in the chassis.
3. If not installing in a rack, place the assembled chassis on a solid at
surface such as a cabinet or shelf located in a dry, well ventilated area.
4. Connect the devices per their specic documentation.
Note: WyreStorm reserves the right to change product specication, appearance or dimensions of this product at any time without prior notice.
Copyright © 2018 WyreStorm Technologies | wyrestorm.com
NHD-000-RACK3 Quickstart Guide | 180410
UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)
7U/8 Slot Rack Mount for NetworkHD™ 600 Series
Quickstart Guide
NHD-000-RACK3
483.0 mm.
19.0 in.
310.3 mm.
12.2 in.
Top
Front Right Side
440.0 mm.
17.3 in.
160.7 mm.
6.3 in.
38.0 mm.
1.5 in.
150.0 mm.
5.9 in.
188.0 mm.
7.4 in.

The NHD-140-RACK-1U is a 1U rack mount that provides a clean installation for up to 2 NetworkHD™ NHD-140-TX encoders.
WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features before beginning the installation
process.
In the Box
1x NHD-140-RACK-1U Chassis
4x Encoder Mounting Bracket
1x Blanking Plate
1x Assembly Screws Pack
Copyright © 2019 WyreStorm Technologies | wyrestorm.com
NHD-140-RACK-1U Quickstart Guide | 190111
UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)
1U / 2 Slot Rack Mount for NHD-140-TX
Quickstart Guide
NHD-140-RACK-1U
Installing Chassis in a Rack
1. Attach the mounting brackets to the sides of the NHD-140-TX
encoder(s) using the supplied screws.
2. Position the NHD-140-TX encoder(s) through the NHD-140-RACK-1U
front face cutout(s) so that the front or rear face of the encoder(s) is
ush with the front face of the NHD-140-RACK-1U.
3. Attach the NHD-140-TX encoder(s) to the NHD-140-RACK-1U main shelf
using the supplied screws.
Secure with Screws
4. Install the blanking plate (if required) using the provided screws
5. Position and install the assembly into the rack and secure with rack
screws (not supplied).
Tip: To keep the installed devices within operating temperature, do not
position the rack directly above heat generating devices such as ampliers.
1 of 2

Note: WyreStorm reserves the right to change product specication, appearance or dimensions of this product at any time without prior notice.
Copyright © 2019 WyreStorm Technologies | wyrestorm.com
NHD-140-RACK-1U Quickstart Guide | 190111
UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)
Dimensions and Weight
Dimensions and Weight
Rack Units 1U
Height 43.5mm/1.71in
Width 483mm/19in
Depth 162mm/6.38in
Weight (Empty) 1.01kg/2.23lbs
Front Right Side
Top
483.0 mm.
19.0 in.
435.0 mm.
17.1 in.
43.5 mm.
1.7 in.
161.5 mm.
6.4 in.
259.4 mm.
10.2 in.
2 of 2
Other Wyrestorm Rack & Stand manuals