Xilence INTERCEPTOR User manual

1
Content
1. Product Introduction 2
1.1 Specications INTERCEPTOR 2
1.2 Specications INTERCEPTORPRO 3
1.3 Accessory INTERCEPTOR & INTERCEPTORPRO 4
1.4 Additional Accessory INTERCEPTORPRO: 4
2. Installation 5
2.1 Removing the Side Panel 5
2.2 Installing the motherboard 6
2.3 Installing the DVD drive 6
2.4 Installing hard drives 7
2.5 Installing 2.5“ hard drives/SSDs 8
2.6 Installing the power supply unit 10
2.7 Installing the fan in the side panel 11
2.8 Cleaning the side panel lter 11
2.9 Removing the top of the case 12
2.10 INTERCEPTORPRO: Switching the Back Panels 12
2.11 INTERCEPTORPRO: Installing an Extra ITX-System 13
2.12 INTERCEPTORPRO: Water Cooling Installation 13
2.13 Installing the Supporting Feet / Pedestals 14

2
1. Product Introduction
1.1 Specications INTERCEPTOR
Dimensions 230 (W) x 580 (H) x 605 (L) mm
Material SECC
Front Panel: ABS + Mesh Design
Device & HDD 4x 5.25“ (exposed)
4x 2.5” (Hot Swappable Tray)
6x 3.5” (Hot Swappable Tray)
2x 3.5“ (internal)
PCI-Slots 10
Front Ports 1x USB 3.0 + 2x USB 2.0 + HD Audio + Reset + Power
Status LED Power & HDD
Case Fans
(Main Case)
Front: 2x LED 120mm
Back: 1x 140mm
Side: 2x 120mm or 2x 140mm or 1x 230mm (optional)
Top: 3x 120mm or 2x 140mm or 1x 230mm (optional)
Motherboard ITX, mATX, ATX, E-ATX, XL-ATX™, HPTX™
Power Supply ATX

3
1.2 Specications INTERCEPTORPRO
Dimensions 230 (W) x 780 (H) x 605 (L) mm
Material SECC
Front Panel: ABS + Mesh Design
Device & HDD 6x 5.25“ (exposed)
4x 2.5” (Hot Swappable Tray)
8x 3.5” (Hot Swappable Tray)
2x 3.5“ (internal)
PCI-Slots 10
Front Ports Main Case: 1x USB 3.0 + 2x USB 2.0 + HD Audio + Reset +
Power
Top System: 2x USB 2.0 + HD Audio + Reset + Power
Status LED Power & HDD
Case Fans
(Main Case)
Front: 2x LED 120mm
Back: 1x 140mm
Side: 2x 120mm or 2x 140mm or 1x 230mm (optional)
Top: 3x 120mm or 2x 140mm (optional)
Case Fans
(Top System)
Top: 4x 120mm or 3x 140mm (optional) or 2x 230mm
(optional)
Motherboard ITX, mATX, ATX, E-ATX, XL-ATX™, HPTX™
Power Supply ATX (Main System) + SFX (Top System) (optional)

4
1.3 Accessory INTERCEPTOR & INTERCEPTORPRO
User Manual (1x)•
Pedestals / Supporting Feet (2x)•
Cable Strap 80mm (5x)•
Screw bag containing the•
following screws:
Stando
5H-6#*4- 6#*6.5HCu
15x 32x 10x
HDD Screw
6*5KM
Thumb Screw
M3*5
Motherboard
Screw
6#*5B-C
Pedestal Screw
M4*10
Case Screw
6#6HW-TC
PSU Back Plate Mini ITX Back Plate
19x
8x 8x
Fan Back Plate 120mm
1.4 Additional Accessory INTERCEPTORPRO:
Cover for the I/O slot if not used (Top System)•
Three dierent back plates for the Top System•
PSU switching cable for connecting two ATX power•
supplies to one motherboard
PSU Switching Cable
I/O Panel Cover

5
2. Installation
2.1 Removing the Side Panel
Remove the thumb screws from the
rear side of the case.
Then pull the side panel rearwards.
To close again place the side panel
into the guide rails and push it for-
wards with care. Then screw in the two
thumb screws on the rear side.
INTERCEPTORPRO only: To open the
upper system, press the opening me-
chanism inwards simultaneously.

6
2.2 Installing the motherboard
Place the standos in positions that
suit your motherboard.
PLEASE NOTE:
CPU, RAM and any peripheral
installations are not included
in this manual. Please refer to
your motherboard manual for
related installation instructions
and troubleshooting
2.3 Installing the DVD drive
Remove the desired DVD drive panel
from the front and insert the DVD
drive into this position, until the front
of the drive unit is ush with the front
of the case.
Then push the pre-installed screw in
to the point where it can be screwed
into the drive itself.

7
2.4 Installing hard drives
Open the front panel on the left hand
side.
Push the opening mechanism to the
left to release the lever.
Pull the drive plug-in module out of
the case.
Fix the 2.5“ or 3.5“ SATA drive in place
with the screws supplied. When doing
so ensure that the sockets are facing
rearwards and that these are in the
correct position.

8
The cabling for all hard drives is only
performed once. Behind the HDD
plug-in modules you will nd several
boards that you should connect in
advance.
On the INTERCEPTORPRO you will
nd two more HDD plug-in modules
at the top of the case.
2.5 Installing 2.5“ hard drives/SSDs
Take the desired 2.5“ HDD/SSD plug-in
module between your thumb and in-
dex nger and gently press the release
mechanism together.
You can now pull out the plug-in
module.

9
Unlock the 2.5“ plug-in module.
Insert the drive with the connections
facing rearwards. Please ensure that
the drive sits in the four xing points.
Now close the plug-in slot carefully
and replace the cover with care.

10
2.6 Installing the power supply unit
If you are using a power supply from
the XO series that makes use of Direct
Airow Technology, we recommend
that you install the power supply with
fans pointing upwards.
For power supplies with 120 or
135mm fans we recommend an instal-
lation with fans pointing downwards.
Please do not forget to clean the dust
lter regularly.
You can run the electricity cables to
the rear of the motherboard bracket
and x them there. Using rubber
bound cabling ensures perfect order
in the case.
Install the power supply unit in the
lower part of the case. In doing so you
have a free choice of where to place
the fan.