XITONG GT06 User manual

1/ 12
GPS Vehicle Tracker
（GPS+GSM+SMS/GPRS）
User Guide
( Version V1.0)
GT06
Tracking system: http://en.gpsxitong.com/index.aspx
Username: IMEN(ID)
Password:123456

2/ 12
Preface
This manual shows how to operate the device smoothly and correctly. Make sure to read this
manual carefully before using this product. The introduction in this book is just for your reference, if
product appearance and colors different from the real products, please follow the products.
Contents
1．Accessories
2．Product Features
3. Installation Instructions
4. Usage
5. Troubleshooting
6. Warranty
.1.
Accessories
1.1 Power Cord
1.2 Installation Guide
1.3 Microphone ( optional )
1.4 SOS button ( optional )
1.5 Relay ( optional )
.2
．
Product features
2.1 GPS and Quad Band GSM 850/900/1800/1900Mhz
2.2 Input Voltage :8-50VDC or 8-100VDC (optional );
2.3 Tracking by SMS/GPRS
2.4 Tracking on Mobile Phone
2.5 ACC ignition signal be detected , ACC ignition signal is detected , the vehicle's state be prompted ;
2.6 Built-in vibration sensor , to achieve the vehicle intelligent anti-theft ;
2.7 specific number can be set up for SOS alarm and Security alarm ;

3/ 12
2.8 SOS switch button for emergency calls for help ;
2.9 Internal / external microphone and speakers , remote audio monitoring and voice intercom function (
optional ) ;
2.10 Built-in backup battery ,to achieve illegal cutting line alarm ( optional ) ;
.3 . Installation Instructions
3.1 Preparation before installation :
3.1.1 Open the box, check the device model is correct, the accessories are complete, otherwise please contact
your dealer ;
3.1.2 choose the SIM card , the terminal needs to insert a GSM SIM card , optional Unicom or mobile GSM
card (Universal GSM network )
3.1.3 the installation of SIM card , take apart a terminal device , open the SIM card metal cover, put the SIM
card chip into the slot, cover the metal cover.
Note : ⑴before installing or removing the SIM card , turn off th power switch on the Terminal side ;
⑵terminal SIM card need to open GPRS function ;
⑶terminal SIM card needs to open the caller display function ( based on the needs of customers to choose ) ;
⑷If your SIM card is turned to input SIM PIN, please refer to your phone user manual and turn off the SIM
PIN fuction
⑸please make sure that the SIM card has charge. .
3.2Installation the way of terminal installation is the hidden installation , it recommend to be installed by the
technical personnel specified by the distributor . notesas following:
3.2.1 In order to avoid to be damaged by the thief , Equipment selection should be hidden
3.2.2 No together with emission sources , such as Parking sensors, anti-theft devices and other automotive
communications equipment ;
3.2.3 can be fixed by using cable ties , or using a strong double-sided adhesive stickers ;
3.2.4 Equipment’s built-in GSM antenna and GPS antenna should be ensured that a positive upward when
installing ( toward the sky ) , and non- metallic objects blocking shield above and recommend the installation
location :
3.2.4.1 the front windshield hiding place beneath the decorative plates ;
3.2.4.2 Car meter ( epidermis of non-metallic material ) surrounding the shelter ;

4/ 12
3.2.4.3 below under car windshield after decorative plates ;
3.2.4.4 car door or inside the column ;
3.2.4.5 inside the electric car / motorcycle shelter beneath the dashboard or rear seat.
NOTE : If the metal layer or heat insulating layeris attached below the windshield , it will lower the received
GPS signal , resulting in GPS work’s
Malfunction , please change equipment installation location.
3.3 terminal outlet defined
1 , The red line is connected to the positive pole ,
2 , The black line is connected with the cathode of the power
3 , the orange wire is connected to ACC,
4 , the yellow line access Oil cut-off electric / lock the car relay.
3.4 Terminal wiring diagram
Please use the original power cord , the red line is the positive power , black for negative power , negative

5/ 12
power installation, choose a separate grounding or grounding , not connected with other common ground . If
ACC auto- theft feature is required, being sure to connect the ACC line , the device state to decide whether to
enter the ACC fortified state ; Without access ACC line, the vehicle will enter the fortified state , vibration
occurs at the maximum security state of the vehicle is running , it will trigger vibration alarm .
3.5 Proper use of the product : Installation →Power →Settings →Registration
Installation : The installation , you should make the GPS antenna towards the sky , above themounting location
must be no electromagnetic wave absorption materialQuality ( such as metal , heat -proof membrane ) occlusion
place.
Power : the SIM card installed in the right direction , according to the terminal wiringdirection , according to the
terminal wiringswitch.Settings: must be done , or can not perform other operations , the use of owner’s mobile
phoneto send text messages to set a specific number to the owner of the terminal number and SIM card .
Registration : registration method based on different dealer’s platforms. registration method is different , please
consult your dealer.
3.6 Indicator Description
3.6.1Red LED---indicate charge sate
state means
Flashing(every 2 second)
charging was completed
、normal
ti
No light
Power is low / no boot
3.6.2yellow LED--- indicate the GSM signal state
state means
Flashing(every 2 second)
GSM initializing
Constant Lighting
Normal GPRS communications / online
No light
GSM sleep
3.6.3blue LED--- indicate the GPS signal state
state means
Flashing(every 2 second)
GPS Seach Signal
Constant Lighting
working and has located
No light
GPS
sleep
.4. User
Note : GPS vehicle positioning terminal communicationsset parameters via SMS , the owner’s phone number to
send SMS code to the GPS vehicle positioning terminal communication SIM card number, separated by a
comma symbol , the following function parameter setting instruction format Comma English input state format.
4.1 owner’s password setting : the owner can only bind a number ,the last number of owners is valid default
owner password is: 123456 Set the owner number instruction are : admin123456 13712345678

6/ 12
Modify the owner password command : password123456 666888 (666888 is the new password )
4.2 SOS set a specific number
Specific number is the alarm number , you can send text messages to increase the terminal commands specific
numbers to add numbers , you can add three ,
101 is the first , 102 is the second , 103 is the third , in the alarm state , the terminal will send thePositioning
information or help to a specific number ( information is based on the needs to be set ) , and the cycle call until
the dial up . Before setting specific numbers , all numbers can be set and query. After setting a specific
number ,specific number without a password can only be associated with the instruction set .
4.2.1 increase the specific number : Instruction Format: 101 # number #
Example : # 13712345678 # 101
reply message : ok
4.2.2 delete a specific number:
Instruction format:
D101 #
D102 #
D103 #
Example : D101 # indicate to delete the first number.
Reply Information : OK
4.2.3 query a specific number : Instruction Format : C10 #
Example : C10 #
Reply Information : 101 # 13712345678
102 # 13712345688
103 # 13712345698
4.3 off the main power alarm settings
4.3.1 turned on the power-off alarm message : pwrsms123456, 1 ( default ) Reply : pwr sms alarm set ok
4.3.2 shut off SMS alarm : pwrsms123456, 0 reply : pwr sms alarm set ok
4.3.3 turned on the power-off phone alarm : pwrcall123456, 1 Reply : pwr call alarm set ok

7/ 12
4.3.4 shut off phone alarm : pwrcall123456, 0 ( default ) Reply : pwr call alarm set ok
4.4 ACC alarm settings ( lines need to be properly connected to the ACC )
4.4.1 ACC ( open start switch by car keys ) in the open state , if it is the auto-arming state , ACC can open to
Anti- automatic solution . If fortification via SMS or platform , ACC does not anti- solution automatically as it
is turned on.
4.4.2 ACC in the closed ( car key switch is turned off ) state , after a set period of time , will enter into the auto-
arming state.
4.5 vibrating alarm settings
4.5.1 Open the vibration alarm messages : 125 # ( default ) Reply message : OK
4.5.2 Close vibrating alarm messages : 126 # Reply message : OK
4.5.3 Open the vibration phone alarm : 122 # Reply message : OK
4.5.4 Close vibrating phone alarm : 121 # ( default ) Reply message : OK
4.5.6 Set the duration of the vibration alarm SMS commands , 1-15 seconds. Instruction : vibtime123456, n
Reply : vibtime set ok n (0 ~ 15), 0 to cancel vibration alarm , default 3 seconds , namely vibration alarm for 3
seconds
Vibration alarm Description : connect the main power , ACC closed ( car key switch is turned off ) state , after
10 minutes into the maximum security state automatically, anti-theft feature is turned on , the occurrence of
illegal vehicle vibration ,thevibration alarm warning will be issued .
If you turn on the phone vibrating alarm, terminal dialed owner’s number was set before , the owner answer the
phone ,then it can remotely monitor vehicle movement.
4.6 SOS alarm settings
When facing with an emergency situation and need help , you can press the SOS button ,SOS emergency alarm
will be triggered . terminal will send a warning message SOS to a SOS specific number was set before and
dialing SOS specific numbers until the dial up , the terminal will upload SOS alarm message to monitoring
platform . Note : SMS and phone alarm required to set up the owner’s number first , SOS alarm to be set a
specific number.
4.6.1 SOS alarm messages Open Instruction, sossms123456
Reply : sossms ok
4.6.2 SOS alarm messages close Instruction , no sossms123456 ( default )

8/ 12
Reply : no sossms ok
4.6.3 SOS alarm call open instruction , soscall123456 ( default )
Reply : soscall ok
4.6.4 SOS alarm call close instruction , no soscall123456
Reply : no soscall ok
4.7 Remote monitoring
SMS Format: 88
When the owner’s number or a specific number to send this command to the terminal SIM card , call back to
achieve the monitoring function.
Note: The implementation of this function must first set the owner number and SOS specific numbers.
4.8 Voice Intercom ( optional ) when the terminal is called the call center or caller, the terminal product can
achieve voice intercom with the called person, to provide help in the emergency , Simultaneously, care staff or
call center can also take the initiative to be custodial staff . Click the SOS button , make a call , press to hang
up . When an incoming call, there is ringing reminder , click the SOS button to answer , press again to hang up .
Note: The implementation of this function must first set up a specific number.
4.9 SMS query location
4.9.1 As the location information of the terminal equipment needs to be queried , you can write the location
query message and sent to the terminal device SIM card the terminal reply the last location information .
SMS : 123
Note: The device can only resolve the Chinese address, users in other countries can use our mobile APP
4.9.2 owners and specific card number calls back to the location information ,the bell twice to hang up
4.10 speed alarm setting
speed limit of the speed alarm message : speed123456 080 set the speed limit of 80 km / h
4.10.1 Close speeding SMS notification : speed123456 000 ( default )
Reply : speed ok
4.10.2 Open the speeding SMS notification : speed123456 080 Re : speed ok
4.11 Displacement alarm setting

9/ 12
Displacement alarm settings command : move123456 300 ( default ) Unit : meter Re : move ok
4.12 fortification disarm SMS setting
SMS fortification : SF Re : SF OK
SMS disarm : CF Re : CF OK
4.13 off the oil and power-offmessage( optional )
When the vehicle was stealed , unsolicited set the off the oil and power-offinstruction by monitoring
background, to ensure the safety of the vehicle move, cutting of the stolen vehicle’s oil-way, to achieve
that the vehicle can’t be started .
Note: To ensure the safety of the vehicle , the terminal perform off electricity and oil operationsonly in
the GPS positioning state, and vehiclemeet :Under conditions of speed less than 20KM / H or
stationary .
When the robbery alarm is released, the monitoring of the background Manual issued to restore oil
electric instruction, terminal performs recovery oil electric action,the vehicle will be able to continue
driving.
SMS off oil : DY
SMS open oil : KY
4.14 GPS reboot
SMS : CQGPS
4.15 restore factory settings :
SMS command : FORMAT
4.16 device reboots
SMS : CQ
4.17 query device information
SMS : CXZT
4.18 APN settings:
Set APN instruction format : apn123456 apn (about APN please consult your SIM card supplier )
Reply : apn ok
Set APN corresponding user name instruction format : apnuser123456 user

10 / 12
Reply : apnuser ok
Set APN corresponding password command format : apnpasswd123456 password
Reply : apnpasswd ok
4.19 set the server IP and port :
SMS : IP + space + IP address + space + port number
Example : IP 219.143.106.193 8500 Re : set IP OK
4.20 -platform applications ( the dealer’s platforms are different, consult your dealer platforms URL )
4.20.1 Real-time monitoring, network / phone search vehicles
GPS + LBS Bi-mode positioning , GPS positioning accuracy of 2 meters , when there is GPS signals
to use the GPS positioning, in a place with no GPS signal to use LBS base station location, automatic
switching bi-mode, keep your GPS vehicle positioning terminal communication online , make sure
your monitoring 365 days ×24 hours and always online.
4.20.1 Mobile real-time monitoring : mobile Internet to landing the domain
For example:
4.20.2 platform for real-time monitoring : PC Internet logindomain
Example : http://www.aika110.com
4.20.2 track playback
Landing platform , click the historical track playback function
4.20.3 report statistics logistics enterprises can set being monitored cargo’s departure time , route point
notification , alarm lines , regional alarm , heavy collision warning , rollover warning , driving speed,
etcthrough the software , we will analyze goods Comprehensively in transit conditions, issued
statements.
Landing platform , point report statistics .
.5. Troubleshooting
5.1 terminal was unable to connect to the backend server after the initial installation , the background is
not displayed on-line , check the terminal installation:
5.1.1 whether main power wiring is correct, pay attention not to connect the interior vehiclecontrol
line.