XT XT-6300 Series User manual

Xirgo Technologies
XT-6300 Series Installation Guide
Version 1.3

1
Version 1.3
Contents
Document Change History.......................................................................................................................... 2
Hardware Specification............................................................................................................................... 3
Connectors IO Interface: ............................................................................................................................. 4
LED Definition ............................................................................................................................................... 6
Current Consumption ................................................................................................................................... 6
Device Mounting Options ............................................................................................................................. 6
Device Configuration using PC ...................................................................................................................... 7

2
Version 1.3
Document Change History
Revision
Date
Changes
1.1
03/02/2015
Draft
1.2
04/15/2015
Updated 14 PIN Molex Table & Hardware Table
1.3
07/30/2015
Updated Hardware Specifications

3
Version 1.3
Hardware Specification
Cellular Wireless Technology:
2G/GSM/GPRS/EGPRS: 850/900/1800/1900 Bands - Models: XT6350/ XT6355
3G (UMTS): 850/1900 Bands (Bands V, II) - Models: XT6360
CDMA (1xRTT): 850/1900 Bands - Models: XT6350
Parameter
Spec
GPS Specification
Receiver
56 channels
Receiver tracking
sensitivity
-162 dBm
Receiver Cold Start
-148dBm
CEP Accuracy
+/- 2.5m
TTFF
- Cold Start
- Hot Start
<29 sec
< 1 sec
HW Options:
3-axis Accel.
BT/BTLE
Last Gasp Back-up
Battery
Internal 250 mAh rechargeable Li-
Ion
Power Requirements
D.C. Power
9-32V
Physical Connection
Data Connector
24-pin Molex Main
14-pin Molex OBD/J-Bus
Antenna:
Cellular/GPS /BT
Internal
SIM Access (2G/3G)
N/A
Programming
Serial
Xirgo Device Manager (XDMI)
Mechanical
Case Material
PC2407, Black
Dimension
3.05”x 3.08”x 0.8”
Weight
3 oz.
Operating
Temperature
-30C to +75C
Certifications
Product
(CDMA) FCC ID: GKM-XT6350
(3G): FCC ID: GKM-XT6360
IC: 10281A-XT6350
Carrier
Verizon, ATT
Notes:
TTTF: All satellites at -130 dBm ; Accuracy: CEP, 50%, 24 hours static, -130 dBm, > 6 SVs

4
Version 1.3
Connectors IO Interface:
Main 24-pin Molex Connector (IO Interface):
Molex 24 pin connector part number: 43025-2400
Molex male pins part number: 43031-0002
Molex 24-pin Header Diagram (On Device):
Molex 24 pin header part number: 43045-2421
Molex 24-pin Pinout Table:
Pin No.
Pin Name
Comments
1
12/24 Volt Power
2
LED+12V
w/5K limiting resistor (panic
LED)
3
Ground
Main Battery GND
4
Ign Out
Buzzer +12V/24V with 560 ohm
5
IN0
Ignition Sense
6
IN1
7
IN2
8
IN3
Panic: pin3 on panic 4-pin Molex
9
IN4
10
OUT0
Buzzer GND
11
OUT1
12
OUT2
Panic: pin4 (LED) on panic 4-pin
Molex
13
Garmin PWR
12V/2A Switched
14
Serial Port-1 TX
Garmin FMI Tx
15
Serial Port-1 RX
Garmin FMI Rx
16
Serial Port-1 GND
Garmin FMI GND
17
Serial Port-2 TX
18
Serial Port-2 RX
19
Serial Port-2 GND
20
1-Wire Serial Main
iButton Data (default)
21
1-Wire Serial Sec.
22
Ext. ADC
23
Spare GND
Panic GND
24
Spare GND
1
2
3
=
4
5
6
7
8
9
=
10
11
12
19
20
21
=3
22
23
24
13
14
15
=3
16
17
18

5
Version 1.3
OBD 14-pin Molex connector (OBD2/JBUS/SWC):
Molex 14 pin connector part number: 043025-1400
Molex male pins part number: 43031-0002
Molex 14-pin Header Diagram (On Device):
Molex 14 pin connector part number: 43045-1421
Molex 14-pin Pinout Table:
J1962 OBD2
Pin No.
XT6350
Pins
XT6350 Pin Description
9 Pin J-Bus
6 Pin J-Bus
6
1
CAN_HS_H
C
2
J1708_RXD
G
B
3
J1708_TXD
F
A
15
4
L_LINE
10
5
J1850_NEG
2
6
J1850_POS
7
14
8
CAN_HS_L
D
3
9
CAN_MS_H
11
10
CAN_MS_L
1
11
SWC_BUS
7
12
K_LINE
5&4
13
GND
A
E
16
14
Vehicle Power (VBAT)
B
C
1
2
3
4
5
6
7
8
9
10
11
12
13
14

6
Version 1.3
LED Definition
Current Consumption
OPERATING MODE
CURRENT CONSUMPTION
Deep Sleep
3 mA
Standby
10 mA
Active Transmit/Receive
65 m
Device Mounting Options
The XT6350 must be securely installed. The XT650 accelerometer will not calibrate if unit is loose
and moves when vehicle is in motion. When mounting the XT6350 use the space provided to
insert a tie strap to secure the device.
BASE
UNIT
LED
Description
Status
Cellular (Amber)
Searching for Cellular Network
LED OFF
Cellular Carrier Lock
Solid
GPS (Green)
Searching for satellite
Solid
GPS Lock
Blinking
Optional
Bluetooth (Blue)
TBD
TBD

7
Version 1.3
Device Configuration using PC
a. A RS-232 to USB TTL converter cable is required to connect a XT-63XX device to a computer for
local configuration. Serial Port # 2 is used for configuration. Connect the XT63XX Tx wire to the
TTL converter cable Rx wire. Connect the XT-63XX Rx wire to the TTL converter cable Tx wire.
Connect the XT-63XX ground wire to the ground wire of the TTL converter cable. Use a terminal
application to connect to the COM port associated with the TTL converter cable. Use the
following settings:
A. Terminal Application Settings:
a. Bits per second: 115200
b. Data bits: 8
c. Parity: None
d. Stop bits: 1
e. Flow control: None
B. Load Script File with the following command
a. :grscr x 2 "D_Script3_20.bin>"
b. Upload file with terminal program
C. Load Parameter File with the following command
a. :gycfg x 2 "Name of file"
b. Upload file with terminal program
D. Save the configuration
a. :vycfg