YAMAN STA-170 User manual
STA170-1-001E
Instruction Manual
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Before Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Treatment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
How to Use each Treatment Mode . . . . . . . . . . . . . . . 13
After Treatment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Frequently Asked Questions (FAQ) . . . . . . . . . . . . . . 23
After Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Use in Foreign Countries . . . . . . . . . . . . . . . . . . . . . . . 7
Table of Contents
Keep this Instruction Manual for future reference.
Refer to the Safety Precautions section for important information.
Before using this product, please read these instructions
carefully.
Rei Beauté
21
Safety Precautions
Safety Precautions
WARNING
Safety Precautions
Do not use under any of the following conditions as this may
cause malfunction of medical devices:
Do not use in conjunction with any medical electronic equipment
such as a pacemaker, oxygenator, electrocardiograph, etc.
Consult a doctor or the manufacturer of the medical electronic
equipment before using this device.
To avoid accident or injury to your skin or body, do not use
under the following conditions:
· While pregnant or nursing or during menstruation
· While growing or during adolescence
· If you suffer from atopic dermatitis or have unusually sensitive skin
· If you have skin allergies or bleeding diathesis
· If you have skin irritation or redness caused by sunburn
· There is suppuration or inflammation of the skin
· You experience skin irritation caused by cosmetics
· Have itchy pigmentation or pathologic pigmentation
· Have viral warts or melanoderma
· Have abnormal blood pressure
· Have weak skin sensibility
· If you are sick or feeling unwell
· If you have capillary dilatation due to long term use of steroid
hormonal drugs or a disorder of liver function
· If you are under a doctor's care
Do not use if you suffer from any of the following conditions,
or on body areas listed below as this may cause injury:
Acute disorder, febrile disorder, contagion, fissures, unusual warts,
feeling unwell, extremely exhausted, tuberculosis, abnormal blood
pressure, malignancy, heart disease, blood or visceral disease,
epilepsy, photo sensitive, or if you have consumed alcohol or
medication that causes drowsiness.
Do not use on wounds, scars, parts of skin that are darker than your
usual skin tone including tattoos, body painting, dark brown spots, or
moles.
Do not use inside mouth or around the pubic area, lips, mucous
membranes, over the Adam's apple, on eyelids or eyeballs, or
around the eyes.
Do not use on areas where you have had plastic surgery.
Do not use on or around eyebrows, forehead, head, ears, nipples,
areola, inside umbilicus, large veins, or over acne.
If you are not sure, consult your doctor before use.
WARNING
Improper use of this device may pose a risk of
death or serious injury.
WARNING
Improper use of this device may result in fire,
injury, or property damage.
CAUTION
Please read all instructions carefully for safe and proper use.
Use only as directed.
Immediately discontinue use if any malfunction or unusual
reaction to treatment occurs.
Precautions listed in the instruction manual are very important.
For your safety, please follow them carefully.
Precautions are classified as WARNING or CAUTION in order to
clearly specify the level of danger and possible injury or damage
that may occur if the device is misused.
This symbol shows you what you must be careful with.
This symbol shows you what you must do.
This symbol shows you what you must NOT do.
Do not use near children.
The intense light may cause
serious eye injury.
Do not emit the flash directly
in or over eyes.
Direct exposure may cause
serious eye injury.
Do not block the vents.
Blocking the vents may
overheat the unit and cause
smoke or fire.
Do not touch the filter right
after flash emission.
The filter will get very hot after
flash emission. Touching the
filter may cause burns.
21
Safety Precautions
Safety Precautions
WARNING
Safety Precautions
Do not use under any of the following conditions as this may
cause malfunction of medical devices:
Do not use in conjunction with any medical electronic equipment
such as a pacemaker, oxygenator, electrocardiograph, etc.
Consult a doctor or the manufacturer of the medical electronic
equipment before using this device.
To avoid accident or injury to your skin or body, do not use
under the following conditions:
· While pregnant or nursing or during menstruation
· While growing or during adolescence
· If you suffer from atopic dermatitis or have unusually sensitive skin
· If you have skin allergies or bleeding diathesis
· If you have skin irritation or redness caused by sunburn
· There is suppuration or inflammation of the skin
· You experience skin irritation caused by cosmetics
· Have itchy pigmentation or pathologic pigmentation
· Have viral warts or melanoderma
· Have abnormal blood pressure
· Have weak skin sensibility
· If you are sick or feeling unwell
· If you have capillary dilatation due to long term use of steroid
hormonal drugs or a disorder of liver function
· If you are under a doctor's care
Do not use if you suffer from any of the following conditions,
or on body areas listed below as this may cause injury:
Acute disorder, febrile disorder, contagion, fissures, unusual warts,
feeling unwell, extremely exhausted, tuberculosis, abnormal blood
pressure, malignancy, heart disease, blood or visceral disease,
epilepsy, photo sensitive, or if you have consumed alcohol or
medication that causes drowsiness.
Do not use on wounds, scars, parts of skin that are darker than your
usual skin tone including tattoos, body painting, dark brown spots, or
moles.
Do not use inside mouth or around the pubic area, lips, mucous
membranes, over the Adam's apple, on eyelids or eyeballs, or
around the eyes.
Do not use on areas where you have had plastic surgery.
Do not use on or around eyebrows, forehead, head, ears, nipples,
areola, inside umbilicus, large veins, or over acne.
If you are not sure, consult your doctor before use.
WARNING
Improper use of this device may pose a risk of
death or serious injury.
WARNING
Improper use of this device may result in fire,
injury, or property damage.
CAUTION
Please read all instructions carefully for safe and proper use.
Use only as directed.
Immediately discontinue use if any malfunction or unusual
reaction to treatment occurs.
Precautions listed in the instruction manual are very important.
For your safety, please follow them carefully.
Precautions are classified as WARNING or CAUTION in order to
clearly specify the level of danger and possible injury or damage
that may occur if the device is misused.
This symbol shows you what you must be careful with.
This symbol shows you what you must do.
This symbol shows you what you must NOT do.
Do not use near children.
The intense light may cause
serious eye injury.
Do not emit the flash directly
in or over eyes.
Direct exposure may cause
serious eye injury.
Do not block the vents.
Blocking the vents may
overheat the unit and cause
smoke or fire.
Do not touch the filter right
after flash emission.
The filter will get very hot after
flash emission. Touching the
filter may cause burns.
43
Safety Precautions
Safety Precautions
WARNINGWARNING
If any problem occurs
during use, unplug the AC
adapter immediately.
D i s c o n t i n u e u s e i f t h e
device does not operate
properly, or emits smoke,
an unusual noise, or odor.
Unplug the AC adapter
from the wall socket when
not in use or when cleaning
to avoid a potential
electrical shock hazard,
short circuit, or fire.
C h e c k a n d c l e a n t h e
treatment window on a
regular basis to avoid risk
of burns or malfunction.
Use only the supplied AC
adapter to avoid electrical
shock hazard, short circuit,
fire, or malfunction.
Use at AC100-240V only.
Make sure the AC adapter
is firmly and securely
plugged into the wall
socket while in use to
avoid a potential fire,
electrical shock hazard, or
malfunction.
Do not allow the main unit,
AC adapter, or cord to get
wet.
Do not use or store near
water or humid places such
as bathrooms as this may
cause an electrical shock
hazard, short circuit, fire,
or malfunction.
Do not use an extension
cor d as this m ay cau se
damage, overheating, or
fire hazard.
Use only as directed in this
instruction manual.
Improper use may cause
injury or malfunction.
Hold the head of the plug
instead of the cord when
unplugging the adapter
from the wall socket. Be
careful not to touch the
metal prongs or parts. Do
not handle with wet hands.
Damage to the cord may
cause an electrical shock,
short circuit, or fire hazard.
Do not disassemble,
attempt to repair, or modify
this device in any way as
this may cause a fire,
electrical shock hazard, or
injury. Consult your local
agent if repair is needed.
Do not allow children or
disabled persons to use
the device unattended.
If you are underage, do not
u s e w i t h o u t a p a r e n t ' s
permission and only use
under parental supervision
to avoid injury.
Do not place the device
near fire, flame, flammable
objects, under direct
s u n l i g h t , o r i n h u m i d
places such as the
bathroom. Do not dispose
of in a fire or place near
heating equipment as this
may cause overheating,
malfunction, fire hazard, or
explosion.
Do not drop, hit, or place
heavy objects on the main
unit as this may cause a
malfunction, crack the
glass tube, or cause injury.
D o n o t u s e i f t h e A C
adapter is damaged or the
wall socket is loose as this
may cause electrical shock
hazard, short circuit, or
fire. Consult your local
agent for repair.
Do not move or lift the
main unit by pulling the AC
adapter.
Doing so may cause
electrical shock hazard,
short circuit, fire, or
disconnection.
Do not use the device in
dark places as this may
cause eye injury or cause
the device to malfunction.
Do not use the device near
flammable substances or
objects such as alcohol,
thinner, benzene, nail
polish remover, or spray
cans as this ma y cau se
fire, electrical shock
hazard, or injury.
Do not look directly into
the treatment window
(flash) or allow others to
look at the emitting flash.
I f a n y p r o b l e m o c c u r s
during use, including
abnormal odor, smoke, or
excess heat, discontinue
use since this may cause
damage or fire.
Do not damage, modify,
bend by force, or bundle
the cord.
Do not place heavy objects
on the cord or allow it to
get pinched in between
other objects as this may
damage the cord and cause
a fire or electrical shock
hazard.
Do not use the device for
extended periods.
(Not for professional use.)
Allow at least 10 minutes interval
after 20 minutes of use. Not
following this instruction may
cause the glass tube to crack or
overheat, or may cause injury.
If you do not hear the fan
running when using the
Flash mode, immediately
discontinue use.
(Hearing a buzzing tone is
normal.)
Continued use of the device
under this condition may cause
smoke, fire, malfunction, or risk of
injury. Consult your local agent if
repair is needed. Do not point the treatment
window at a black object as
this may cause the device
to not work properly.
43
Safety Precautions
Safety Precautions
WARNINGWARNING
If any problem occurs
during use, unplug the AC
adapter immediately.
D i s c o n t i n u e u s e i f t h e
device does not operate
properly, or emits smoke,
an unusual noise, or odor.
Unplug the AC adapter
from the wall socket when
not in use or when cleaning
to avoid a potential
electrical shock hazard,
short circuit, or fire.
C h e c k a n d c l e a n t h e
treatment window on a
regular basis to avoid risk
of burns or malfunction.
Use only the supplied AC
adapter to avoid electrical
shock hazard, short circuit,
fire, or malfunction.
Use at AC100-240V only.
Make sure the AC adapter
is firmly and securely
plugged into the wall
socket while in use to
avoid a potential fire,
electrical shock hazard, or
malfunction.
Do not allow the main unit,
AC adapter, or cord to get
wet.
Do not use or store near
water or humid places such
as bathrooms as this may
cause an electrical shock
hazard, short circuit, fire,
or malfunction.
Do not use an extension
cor d as this m ay cau se
damage, overheating, or
fire hazard.
Use only as directed in this
instruction manual.
Improper use may cause
injury or malfunction.
Hold the head of the plug
instead of the cord when
unplugging the adapter
from the wall socket. Be
careful not to touch the
metal prongs or parts. Do
not handle with wet hands.
Damage to the cord may
cause an electrical shock,
short circuit, or fire hazard.
Do not disassemble,
attempt to repair, or modify
this device in any way as
this may cause a fire,
electrical shock hazard, or
injury. Consult your local
agent if repair is needed.
Do not allow children or
disabled persons to use
the device unattended.
If you are underage, do not
u s e w i t h o u t a p a r e n t ' s
permission and only use
under parental supervision
to avoid injury.
Do not place the device
near fire, flame, flammable
objects, under direct
s u n l i g h t , o r i n h u m i d
places such as the
bathroom. Do not dispose
of in a fire or place near
heating equipment as this
may cause overheating,
malfunction, fire hazard, or
explosion.
Do not drop, hit, or place
heavy objects on the main
unit as this may cause a
malfunction, crack the
glass tube, or cause injury.
D o n o t u s e i f t h e A C
adapter is damaged or the
wall socket is loose as this
may cause electrical shock
hazard, short circuit, or
fire. Consult your local
agent for repair.
Do not move or lift the
main unit by pulling the AC
adapter.
Doing so may cause
electrical shock hazard,
short circuit, fire, or
disconnection.
Do not use the device in
dark places as this may
cause eye injury or cause
the device to malfunction.
Do not use the device near
flammable substances or
objects such as alcohol,
thinner, benzene, nail
polish remover, or spray
cans as this ma y cau se
fire, electrical shock
hazard, or injury.
Do not look directly into
the treatment window
(flash) or allow others to
look at the emitting flash.
I f a n y p r o b l e m o c c u r s
during use, including
abnormal odor, smoke, or
excess heat, discontinue
use since this may cause
damage or fire.
Do not damage, modify,
bend by force, or bundle
the cord.
Do not place heavy objects
on the cord or allow it to
get pinched in between
other objects as this may
damage the cord and cause
a fire or electrical shock
hazard.
Do not use the device for
extended periods.
(Not for professional use.)
Allow at least 10 minutes interval
after 20 minutes of use. Not
following this instruction may
cause the glass tube to crack or
overheat, or may cause injury.
If you do not hear the fan
running when using the
Flash mode, immediately
discontinue use.
(Hearing a buzzing tone is
normal.)
Continued use of the device
under this condition may cause
smoke, fire, malfunction, or risk of
injury. Consult your local agent if
repair is needed. Do not point the treatment
window at a black object as
this may cause the device
to not work properly.
65
Safety Precautions
Safety Precautions
CAUTIONCAUTION
Always use an intensity
level that is suitable for
your skin. Refer to “How to
set the Flash level” (p.11)
If using the device for the first
time, or until you get used to
using the device, always start
from level 1.
Use only in the proper
operational environmental
temperature of 5°C - 35°C.
Check the temperature of
the environment you are in
before using the device to
prevent possible damage
or malfunction.
NOTE: If there is a sudden
change in temperature, it
may take some time for the
device to adapt to the new
environment.
Always refer to After
Treatment section in this
instruction manual (p.19)
after each use. Remove
hair debris and cosmetics
from the main unit since
this may cause skin burns,
a malfunction, or skin
irritation.
Always shave the treatment
area before applying flash
treatment. If you apply
flash to skin with long hair
remaining, hair debris may
adhere to the treatme nt
window and cause burns
o n t h e w i n d o w . G e n t ly
remove hair debris or dirt
from the treatment window
using a cotton tip.
Brush away any hair debris
on the ski n as th is ma y
cause your skin to feel
more heat during flash
emission.
Use a moisturizer on a
daily basis to prevent your
skin from overdrying. If
your skin is too dry, you
m a y n o t g e t t h e b e s t
results.
Avoid exercise, bathing
in a hot tub, or drinking
alcohol until the day after a
treatment as this may
cause skin irritation.
If your skin continues to
feel warm after treatment,
you can cool down the skin
completely with a cold
towel.
Skin may remain warm
after treatment depending
on your body condition or
o n h o w t h e d e v i c e h a s
b e e n u s e d . I f t h e s k i n
warmth bothers you, follow
instructions (p.14 sec.7) to
treat the symptom.
If this symptom does not
improve, consult your
doctor.
Avoid sun or UV exposure
to areas that have been
treated for at least 24 hours
after treatment. If redness
remains after 24 hours,
continue to avoid sun
exposure. Also apply
sunscreen to protect the
skin during the treatment
period to avoid potential
skin problems.
Make sure there are not
any dark or black objects,
cosmetics, dirt, or hair
debris on the attachment
before use as th i s m a y
cause skin burns, damage
the attachment, or lead to a
possible malfunction.
Do not use out of doors or
under direct sunlight as
this may cause malfunction
or the device may not work
properly.
D o n o t u s e o n p e t s o r
animals as this may cause
injury.
D o n o t u s e i f y o u a r e
experiencing skin rash,
irrita t i o n, o r i t c hiness.
Discontinue use if you
experience an abnormal
skin r e actio n durin g or
after treatment.
Do not wipe the device with
solvents such as alcohol,
thinner, benzene, nail
polish remover, as this may
cause damage to the
surface of the main unit.
Do not apply flash on
clothes, objects, or your
head hair as this may
cause burns, discoloration,
or damage.
Do not apply perfume or
makeup on areas that have
just been treated as this
may cause skin problems.
(Not including skin care
products for moisturizing.)
Do not apply antiperspirant
right after performing
treatment on underarms.
Refrain from use until
redness completely fades
away.
Do not place the device
near objects that are
susceptible to magnetism
as this may cause damage
to the objects, or result in a
malfunction of the device.
Make sure the treatment
window is not broken,
distorted, discolored, or
damaged.
D o n o t u s e i f y o u s e e
damage or broken parts on
the device as this may
worsen the damage or
cause burns or injury to the
skin or fingers.
Do not use more than once
a day on the same area.
Excess treatment does not
improve effectiveness.
For best results, follow the
treatment frequency
recommendations (p.12).
Treatment areas may be
slightly over lapped during
a treatment.
65
Safety Precautions
Safety Precautions
CAUTIONCAUTION
Always use an intensity
level that is suitable for
your skin. Refer to “How to
set the Flash level” (p.11)
If using the device for the first
time, or until you get used to
using the device, always start
from level 1.
Use only in the proper
operational environmental
temperature of 5°C - 35°C.
Check the temperature of
the environment you are in
before using the device to
prevent possible damage
or malfunction.
NOTE: If there is a sudden
change in temperature, it
may take some time for the
device to adapt to the new
environment.
Always refer to After
Treatment section in this
instruction manual (p.19)
after each use. Remove
hair debris and cosmetics
from the main unit since
this may cause skin burns,
a malfunction, or skin
irritation.
Always shave the treatment
area before applying flash
treatment. If you apply
flash to skin with long hair
remaining, hair debris may
adhere to the treatme nt
window and cause burns
o n t h e w i n d o w . G e n t ly
remove hair debris or dirt
from the treatment window
using a cotton tip.
Brush away any hair debris
on the ski n as th is ma y
cause your skin to feel
more heat during flash
emission.
Use a moisturizer on a
daily basis to prevent your
skin from overdrying. If
your skin is too dry, you
m a y n o t g e t t h e b e s t
results.
Avoid exercise, bathing
in a hot tub, or drinking
alcohol until the day after a
treatment as this may
cause skin irritation.
If your skin continues to
feel warm after treatment,
you can cool down the skin
completely with a cold
towel.
Skin may remain warm
after treatment depending
on your body condition or
o n h o w t h e d e v i c e h a s
b e e n u s e d . I f t h e s k i n
warmth bothers you, follow
instructions (p.14 sec.7) to
treat the symptom.
If this symptom does not
improve, consult your
doctor.
Avoid sun or UV exposure
to areas that have been
treated for at least 24 hours
after treatment. If redness
remains after 24 hours,
continue to avoid sun
exposure. Also apply
sunscreen to protect the
skin during the treatment
period to avoid potential
skin problems.
Make sure there are not
any dark or black objects,
cosmetics, dirt, or hair
debris on the attachment
before use as th i s m a y
cause skin burns, damage
the attachment, or lead to a
possible malfunction.
Do not use out of doors or
under direct sunlight as
this may cause malfunction
or the device may not work
properly.
D o n o t u s e o n p e t s o r
animals as this may cause
injury.
D o n o t u s e i f y o u a r e
experiencing skin rash,
irrita t i o n, o r i t c hiness.
Discontinue use if you
experience an abnormal
skin r e actio n durin g or
after treatment.
Do not wipe the device with
solvents such as alcohol,
thinner, benzene, nail
polish remover, as this may
cause damage to the
surface of the main unit.
Do not apply flash on
clothes, objects, or your
head hair as this may
cause burns, discoloration,
or damage.
Do not apply perfume or
makeup on areas that have
just been treated as this
may cause skin problems.
(Not including skin care
products for moisturizing.)
Do not apply antiperspirant
right after performing
treatment on underarms.
Refrain from use until
redness completely fades
away.
Do not place the device
near objects that are
susceptible to magnetism
as this may cause damage
to the objects, or result in a
malfunction of the device.
Make sure the treatment
window is not broken,
distorted, discolored, or
damaged.
D o n o t u s e i f y o u s e e
damage or broken parts on
the device as this may
worsen the damage or
cause burns or injury to the
skin or fingers.
Do not use more than once
a day on the same area.
Excess treatment does not
improve effectiveness.
For best results, follow the
treatment frequency
recommendations (p.12).
Treatment areas may be
slightly over lapped during
a treatment.
87
A
B3
BF
C
O
Accessories
Cool Plate
(For skin cooling)
Emission
Button
Treatment
Window
(Shown in grey)
* Design and specifications of the main unit and accessories
are subject to change for improvements without prior notice.
Vents
* Do not block
Filter
* Yellow Clear
Glass
AC Adapter Socket
Main Unit
Standby Lamp
Glass Tube
(Flash)
AC AdapterFace Attachment
AC Adapter
Adapter Plug
Product Description
Use in Foreign Countries
WARNING
Be sure to check the plug shape and the voltage before using.
Using this device with an improper plug or at the incorrect
voltage may cause overheating, fire, or malfunction.
NOTE: This product can be operated at 100-240V. If the plug of the
supplied AC adapter does not match the plug of your location, use a
plug adapter (not provided).
Main plug configurations and countries of use
US, Canada, Hawaii, Spain, Guam,
Saipan, Thailand, Korea, Taiwan, China,
Philippines, Vietnam, Brazil, Turkey, etc.
UK, Switzerland, China, Hong Kong,
India, Singapore, Philippines, Egypt,
South Africa, etc.
Canada, UK, Switzerland, Thailand,
Korea, Singapore, China, Hong Kong,
Egypt, South Africa, etc.
The plug configuration and voltage varies depending on the region and
the type of accommodation. Always be sure to check for compatibility
before using the device.
For information about plug adapters, consult a travel agency or a
consumer electronics retailer.
Type Plug Configuration Countries of Use
Use at AC100-240V only to avoid a potential fire or electrical
shock hazard.
Italy, Holland, Switzerland, Spain,
Germany, France, India, Thailand, Korea,
China, Hong Kong, Malaysia, Turkey, etc.
UK, France, Australia, New Zealand,
Korea, Taiwan, China, Philippines,
Argentina, etc.
Use in Foreign Countries
Product Description
87
A
B3
BF
C
O
Accessories
Cool Plate
(For skin cooling)
Emission
Button
Treatment
Window
(Shown in grey)
* Design and specifications of the main unit and accessories
are subject to change for improvements without prior notice.
Vents
* Do not block
Filter
* Yellow Clear
Glass
AC Adapter Socket
Main Unit
Standby Lamp
Glass Tube
(Flash)
AC AdapterFace Attachment
AC Adapter
Adapter Plug
Product Description
Use in Foreign Countries
WARNING
Be sure to check the plug shape and the voltage before using.
Using this device with an improper plug or at the incorrect
voltage may cause overheating, fire, or malfunction.
NOTE: This product can be operated at 100-240V. If the plug of the
supplied AC adapter does not match the plug of your location, use a
plug adapter (not provided).
Main plug configurations and countries of use
US, Canada, Hawaii, Spain, Guam,
Saipan, Thailand, Korea, Taiwan, China,
Philippines, Vietnam, Brazil, Turkey, etc.
UK, Switzerland, China, Hong Kong,
India, Singapore, Philippines, Egypt,
South Africa, etc.
Canada, UK, Switzerland, Thailand,
Korea, Singapore, China, Hong Kong,
Egypt, South Africa, etc.
The plug configuration and voltage varies depending on the region and
the type of accommodation. Always be sure to check for compatibility
before using the device.
For information about plug adapters, consult a travel agency or a
consumer electronics retailer.
Type Plug Configuration Countries of Use
Use at AC100-240V only to avoid a potential fire or electrical
shock hazard.
Italy, Holland, Switzerland, Spain,
Germany, France, India, Thailand, Korea,
China, Hong Kong, Malaysia, Turkey, etc.
UK, France, Australia, New Zealand,
Korea, Taiwan, China, Philippines,
Argentina, etc.
Use in Foreign Countries
Product Description
109
1
2
Shave the treatment area with your own shaver.
Unwanted hair or debris on the skin surface may cause burns.
Do not pluck or wax unwanted hair on areas you wish to treat.
Make sure the attachment and treatment window are clean,
free of dirt and debris, undamaged, and in good condition.
Always clean the treatment window if it is dirty to prevent malfunction,
deterioration, burns, injury, and skin irritation.
Refer to the section “How to Clean” (p.19) for details on cleaning.
Preparing for Treatment
Follow these instructions before every treatment for best results.
Operation Panel
Set the treatment intensity. There are 5 adjustable levels.
With each press of a Level button, the corresponding Level lamp will turn
solid green. At maximum, all 5 Level lamps will be lit.
The higher the level, the more warmth you may feel when using Flash.
Be sure to start from Level 1 until you get used to treatment.
Level UP and Level DOWN Buttons
Lamp off: The unit is in standby (waiting), or the treatment window is not
entirely covering the treatment area.
Solid green: Treatment window is properly touching the skin and pressing
the Emission button will emit flash.
You will hear two short beep tones when the unit is ready for treatment.
Standby Lamp
Power / Cool Button
ON: Press and hold (approx. 3 sec.) to turn ON
(Level 1 lamp will be solid green)
COOL: Press (approx. 1 sec.) to switch to Cool Mode
(Mode Lamp is solid blue)
OFF: Press (approx. 3 sec.) to turn OFF
(Lamps are off)
The fan will run for about 90 seconds after power is turned off.
Do not unplug the AC adapter until the fan stops running.
Level
Indicator
Lamp
Level Up
Button
Level Down
Button
Standby
Lamp
Mode Lamp
Power / Cool Button
Emission
Button
Before Use
Before Use
Before Use
109
1
2
Shave the treatment area with your own shaver.
Unwanted hair or debris on the skin surface may cause burns.
Do not pluck or wax unwanted hair on areas you wish to treat.
Make sure the attachment and treatment window are clean,
free of dirt and debris, undamaged, and in good condition.
Always clean the treatment window if it is dirty to prevent malfunction,
deterioration, burns, injury, and skin irritation.
Refer to the section “How to Clean” (p.19) for details on cleaning.
Preparing for Treatment
Follow these instructions before every treatment for best results.
Operation Panel
Set the treatment intensity. There are 5 adjustable levels.
With each press of a Level button, the corresponding Level lamp will turn
solid green. At maximum, all 5 Level lamps will be lit.
The higher the level, the more warmth you may feel when using Flash.
Be sure to start from Level 1 until you get used to treatment.
Level UP and Level DOWN Buttons
Lamp off: The unit is in standby (waiting), or the treatment window is not
entirely covering the treatment area.
Solid green: Treatment window is properly touching the skin and pressing
the Emission button will emit flash.
You will hear two short beep tones when the unit is ready for treatment.
Standby Lamp
Power / Cool Button
ON: Press and hold (approx. 3 sec.) to turn ON
(Level 1 lamp will be solid green)
COOL: Press (approx. 1 sec.) to switch to Cool Mode
(Mode Lamp is solid blue)
OFF: Press (approx. 3 sec.) to turn OFF
(Lamps are off)
The fan will run for about 90 seconds after power is turned off.
Do not unplug the AC adapter until the fan stops running.
Level
Indicator
Lamp
Level Up
Button
Level Down
Button
Standby
Lamp
Mode Lamp
Power / Cool Button
Emission
Button
Before Use
Before Use
Before Use
1211
1
2
3Do not apply flash on the same area more than once a day.
The results vary from person to person and depend on which body area is treated.
If you are not satisfied with the results, continue to treat every 2 weeks for more
than 2 months until you see the desired results.
This device is not designed for permanent hair removal.
If regular treatment is discontinued, it may be difficult to see results and you may
find that unwanted hair will gradually grow back.
Do not use more often than the recommended frequency of
treatment above.
If you wish to treat the area more than the recommended treatment
frequency, always check your skin condition before and during use.
Do not apply flash on the same area more than once per day as this
may cause skin irritation or damage.
CAUTION
Treatment
Frequency of Treatment
Treatment Steps
< Body Care >
Shave →
Apply flash treatment →
Cool down the treatment area using Cool mode
NOTE: If unwanted hair is longer than 1mm, always shave first before
performing flash treatment.
During first 2 months
Every 2 weeks Once in 4-8 weeks
After 2 months of treatment
①
②
③
< Face Care >
Attach Face Attachment and then perform flash treatment →
Remove Face Attachment →
Cool down the treatment area using Cool mode
NOTE: Shave long unwanted hair, unwanted dark hair, and hair
around the mouth before performing flash treatment.
①
②
③
Test the Flash on a patch of skin
Set the Flash Level
Set to a level at which you feel a mild sensation of warmth
or heat. Do not use at a level that is intolerable.
Adjust the Flash level according to the treatment area.
Do not set the flash level high for those with dark skin tone or
recently tanned skin. Doing so may cause skin irritation.
Press and hold Power / Cool button for approx. 3 seconds
to turn on the power.
Body: No attachment needed.
Face: Use the Face attachment.
* When using the Face attachment, attach it to the treatment
head after turning on the power.
Test the flash on a patch of skin near the area you plan to
treat starting at Level 1.
See section “How to Use Flash Mode” on p.13.
Wait 24 hours and then examine the treatment area.
If the skin appears normal (skin condition without any redness,
blisters, or burns), then start your first treatment.
Please follow these instructions prior to your first treatment.
Before Use
Treatment
1211
1
2
3Do not apply flash on the same area more than once a day.
The results vary from person to person and depend on which body area is treated.
If you are not satisfied with the results, continue to treat every 2 weeks for more
than 2 months until you see the desired results.
This device is not designed for permanent hair removal.
If regular treatment is discontinued, it may be difficult to see results and you may
find that unwanted hair will gradually grow back.
Do not use more often than the recommended frequency of
treatment above.
If you wish to treat the area more than the recommended treatment
frequency, always check your skin condition before and during use.
Do not apply flash on the same area more than once per day as this
may cause skin irritation or damage.
CAUTION
Treatment
Frequency of Treatment
Treatment Steps
< Body Care >
Shave →
Apply flash treatment →
Cool down the treatment area using Cool mode
NOTE: If unwanted hair is longer than 1mm, always shave first before
performing flash treatment.
During first 2 months
Every 2 weeks Once in 4-8 weeks
After 2 months of treatment
①
②
③
< Face Care >
Attach Face Attachment and then perform flash treatment →
Remove Face Attachment →
Cool down the treatment area using Cool mode
NOTE: Shave long unwanted hair, unwanted dark hair, and hair
around the mouth before performing flash treatment.
①
②
③
Test the Flash on a patch of skin
Set the Flash Level
Set to a level at which you feel a mild sensation of warmth
or heat. Do not use at a level that is intolerable.
Adjust the Flash level according to the treatment area.
Do not set the flash level high for those with dark skin tone or
recently tanned skin. Doing so may cause skin irritation.
Press and hold Power / Cool button for approx. 3 seconds
to turn on the power.
Body: No attachment needed.
Face: Use the Face attachment.
* When using the Face attachment, attach it to the treatment
head after turning on the power.
Test the flash on a patch of skin near the area you plan to
treat starting at Level 1.
See section “How to Use Flash Mode” on p.13.
Wait 24 hours and then examine the treatment area.
If the skin appears normal (skin condition without any redness,
blisters, or burns), then start your first treatment.
Please follow these instructions prior to your first treatment.
Before Use
Treatment
1413
2
3
1
4
5
6
7
8
Move the treatment window to the next
adjacent area after each flash to continue
applying treatment to the entire area.
Move to the next area after each flash even
when using repeat flash emission mode.
The treatment window is the size of the area
that will receive each flash emission.
Press and hold the Power/Cool button (approx. 3 seconds)
to turn off the power.
All the lamps will turn off when the power is off
The fan will run for about 90 seconds after power is turned off.
Do not unplug the AC adapter until the fan stops running.
If the skin remains hot after the treatment, use the Cool
mode or a refrigerant or cold towel to cool down the
treatment area. Then apply a moisturizer to soothe the
treatment area.
When you are finished, unplug the AC adaptor from the
wall socket and clean the main unit and attachment.
Follow instructions for “How to Clean” described on p.19. Clean
the unit and accessories after every use.
Do not bathe (showering is OK), exercise, or drink alcohol after
any treatment session until the next day.
This device has a built-in safety feature which only allows the flash to
work when the treatment window is completely flat against the skin
and blocking ambient light. Never use in a dark room since this may
defeat the safety feature and could harm your eyes.
The device may not operate properly under direct sunlight.
The power will automatically turn off 20 minutes after turning on the
power. Allow at least a 10 minute interval before the next use to avoid
malfunction.
The device cannot be used in a dark room.
At higher intensity levels, the standby time (waiting period) will be
longer.
How to Use Each Mode
Plug the AC adaptor into the adapter plug socket and then
into the wall socket.
How to use Flash Mode
Press and hold the Power/Cool button (approx. 3 seconds)
to turn on the power
When using an attachment, first turn on the power and then attach
the attachment.
Level 1 indicator lamp will turn on solid green.
When the power is on, you will hear a humming sound from the
internal fan. This is normal.
Press the Level UP or Level DOWN buttons to set the
treatment level.
This device offers 5 intensity levels for Flash treatment.
Always start from level 1 until you get used to treatment.
When you hear two short beep tones, the device is ready for
treatment.
Place the treatment window flat against the skin and press
the emission button.
The flash will only emit if the standby lamp turns solid green.
Continue pressing the emission button to switch to repeat flash
emission mode (p.15).
Do not look directly into the treatment window when applying
flash.
Apply to skin as shown above.
Treatment
Treatment
1413
2
3
1
4
5
6
7
8
Move the treatment window to the next
adjacent area after each flash to continue
applying treatment to the entire area.
Move to the next area after each flash even
when using repeat flash emission mode.
The treatment window is the size of the area
that will receive each flash emission.
Press and hold the Power/Cool button (approx. 3 seconds)
to turn off the power.
All the lamps will turn off when the power is off
The fan will run for about 90 seconds after power is turned off.
Do not unplug the AC adapter until the fan stops running.
If the skin remains hot after the treatment, use the Cool
mode or a refrigerant or cold towel to cool down the
treatment area. Then apply a moisturizer to soothe the
treatment area.
When you are finished, unplug the AC adaptor from the
wall socket and clean the main unit and attachment.
Follow instructions for “How to Clean” described on p.19. Clean
the unit and accessories after every use.
Do not bathe (showering is OK), exercise, or drink alcohol after
any treatment session until the next day.
This device has a built-in safety feature which only allows the flash to
work when the treatment window is completely flat against the skin
and blocking ambient light. Never use in a dark room since this may
defeat the safety feature and could harm your eyes.
The device may not operate properly under direct sunlight.
The power will automatically turn off 20 minutes after turning on the
power. Allow at least a 10 minute interval before the next use to avoid
malfunction.
The device cannot be used in a dark room.
At higher intensity levels, the standby time (waiting period) will be
longer.
How to Use Each Mode
Plug the AC adaptor into the adapter plug socket and then
into the wall socket.
How to use Flash Mode
Press and hold the Power/Cool button (approx. 3 seconds)
to turn on the power
When using an attachment, first turn on the power and then attach
the attachment.
Level 1 indicator lamp will turn on solid green.
When the power is on, you will hear a humming sound from the
internal fan. This is normal.
Press the Level UP or Level DOWN buttons to set the
treatment level.
This device offers 5 intensity levels for Flash treatment.
Always start from level 1 until you get used to treatment.
When you hear two short beep tones, the device is ready for
treatment.
Place the treatment window flat against the skin and press
the emission button.
The flash will only emit if the standby lamp turns solid green.
Continue pressing the emission button to switch to repeat flash
emission mode (p.15).
Do not look directly into the treatment window when applying
flash.
Apply to skin as shown above.
Treatment
Treatment
1615
1
2
3
How to use the Cool Mode
CAUTION
Press Power/Cool button for approximately 1 second to
switch to Cool mode while the device is turned on.
The Mode lamp will turn on solid blue.
Apply Cool Plate to the treatment area.
Move the device in the direction shown in
the figure at right.
Cool mode does not have adjustable
temperature level settings.
Press and hold the Power/Cool button for approximately 3
seconds to turn off Cool mode if you wish to finish.
The solid blue lamp will turn off when Cool mode is off.
If you wish to apply another flash treatment to a different area, press
the Power/Cool button for approximately 1 second to switch back to
flash mode.
Cool down the treatment area after a flash treatment.
Do not use Cool mode successively.
If not allowed to rest between applications, the Cool Plate will
not fully reach its proper cooling state. Allow at least a 10
minute interval before next use.
< About Single/Repeat Emission Mode >
If you continue to press the emission button, the flash will repeatedly emit
automatically each time the device is ready to flash again. Glide the
treatment window (without lifting) to a new area after each flash.
Do not use in dark areas; this may cause eye injury.
Do not emit flash directly into eyes; may cause eye injury.
Do not emit the flash on your head hair when using the
device on the face. Pull your hair back to keep hair away from
your face during treatment.
Do not touch the filter after use as this may cause burns
and injury to fingers.
Do not use on these areas to avoid skin problems or injuries:
Wounds (scars, or parts of skin that are darker than your
usual skin tone)
Eyeballs
Eyelids, or around eyes
Pimples
Brown spots, moles
Eyebrows, forehead, head hair
Tanned skin
WARNING
Treatment
Treatment
1615
1
2
3
How to use the Cool Mode
CAUTION
Press Power/Cool button for approximately 1 second to
switch to Cool mode while the device is turned on.
The Mode lamp will turn on solid blue.
Apply Cool Plate to the treatment area.
Move the device in the direction shown in
the figure at right.
Cool mode does not have adjustable
temperature level settings.
Press and hold the Power/Cool button for approximately 3
seconds to turn off Cool mode if you wish to finish.
The solid blue lamp will turn off when Cool mode is off.
If you wish to apply another flash treatment to a different area, press
the Power/Cool button for approximately 1 second to switch back to
flash mode.
Cool down the treatment area after a flash treatment.
Do not use Cool mode successively.
If not allowed to rest between applications, the Cool Plate will
not fully reach its proper cooling state. Allow at least a 10
minute interval before next use.
< About Single/Repeat Emission Mode >
If you continue to press the emission button, the flash will repeatedly emit
automatically each time the device is ready to flash again. Glide the
treatment window (without lifting) to a new area after each flash.
Do not use in dark areas; this may cause eye injury.
Do not emit flash directly into eyes; may cause eye injury.
Do not emit the flash on your head hair when using the
device on the face. Pull your hair back to keep hair away from
your face during treatment.
Do not touch the filter after use as this may cause burns
and injury to fingers.
Do not use on these areas to avoid skin problems or injuries:
Wounds (scars, or parts of skin that are darker than your
usual skin tone)
Eyeballs
Eyelids, or around eyes
Pimples
Brown spots, moles
Eyebrows, forehead, head hair
Tanned skin
WARNING
Treatment
Treatment
1817
◆
◆
◆
◆
◆
About the Face Attachment
WARNING
FaceNo Attachment
Fingers
Legs
Arms
Underarms
Face
Area
Recommended Attachment for Treatment Areas
Proper treatment on the face or small areas can be performed by
attaching the face attachment to the device.
Face Attachment
The Face attachment is always recommended for use on facial hair.
Always attach or remove the Face attachment while the power is ON.
Attaching and Removing Face Attachment
Make sure the Face Attachment is securely attached to the device.
Hold the attachment carefully when removing.
Fasten the Face Attachment to the treatment window as shown in the
figure below. The attachment will magnetically stay in place.
Tips for Each Treatment Area
Follow these tips for application to different treatment areas:
Remove all cosmetics, antiperspirants, perfumes, and lotions before
treatment.
Use a mirror for an easier view of the treatment area. Stretch the skin with
your fingers where skin is loose.
You may feel heat if loose skin gets near to the treatment window.
Underarm Treatment
Always use the Face Attachment when treating facial areas.
Avoid sun exposure right after treatment and also avoid getting a tan
during the treatment period.
Stretch narrow or angled areas such as around the mouth which may be
more difficult to reach for treatment (e.g. moustache or beard).
* Never look directly into the flash.
Face Treatment
Use lower levels on areas that have more pigmentation (parts of skin that
are darker than your usual skin tone).
*Always start from level 1 if you are treating for the first time or unfamiliar
with use.
Bikini Line Treatment
Skin over bone or lumpy areas may be sensitive compared to other body
areas and may be more likely to result in some redness.
In such cases, cool down the treatment area by using the Cool mode and
apply a moisturizer after treatment.
Arms / Legs Treatment
Wounds (scars, or parts of skin that are darker than your
usual skin tone)
Eyeballs
Eyelids, or around eyes
Pimples
Brown spots, moles
Eyebrows, forehead, head hair
Tanned skin
Do not use on these areas to avoid skin problems or injuries:
Using Attachments
Treatment Area Tips
1817
◆
◆
◆
◆
◆
About the Face Attachment
WARNING
FaceNo Attachment
Fingers
Legs
Arms
Underarms
Face
Area
Recommended Attachment for Treatment Areas
Proper treatment on the face or small areas can be performed by
attaching the face attachment to the device.
Face Attachment
The Face attachment is always recommended for use on facial hair.
Always attach or remove the Face attachment while the power is ON.
Attaching and Removing Face Attachment
Make sure the Face Attachment is securely attached to the device.
Hold the attachment carefully when removing.
Fasten the Face Attachment to the treatment window as shown in the
figure below. The attachment will magnetically stay in place.
Tips for Each Treatment Area
Follow these tips for application to different treatment areas:
Remove all cosmetics, antiperspirants, perfumes, and lotions before
treatment.
Use a mirror for an easier view of the treatment area. Stretch the skin with
your fingers where skin is loose.
You may feel heat if loose skin gets near to the treatment window.
Underarm Treatment
Always use the Face Attachment when treating facial areas.
Avoid sun exposure right after treatment and also avoid getting a tan
during the treatment period.
Stretch narrow or angled areas such as around the mouth which may be
more difficult to reach for treatment (e.g. moustache or beard).
* Never look directly into the flash.
Face Treatment
Use lower levels on areas that have more pigmentation (parts of skin that
are darker than your usual skin tone).
*Always start from level 1 if you are treating for the first time or unfamiliar
with use.
Bikini Line Treatment
Skin over bone or lumpy areas may be sensitive compared to other body
areas and may be more likely to result in some redness.
In such cases, cool down the treatment area by using the Cool mode and
apply a moisturizer after treatment.
Arms / Legs Treatment
Wounds (scars, or parts of skin that are darker than your
usual skin tone)
Eyeballs
Eyelids, or around eyes
Pimples
Brown spots, moles
Eyebrows, forehead, head hair
Tanned skin
Do not use on these areas to avoid skin problems or injuries:
Using Attachments
Treatment Area Tips
2019
1
2
1
CAUTION
WARNING
Never use solvents such as alcohol, thinner, benzene, or nail
polish remover.
Do not leave or store the device with skin care product or
lotion residue remaining on the device.
Unplug the AC adapter from the wall socket when cleaning.
Cleaning with the adapter attached may cause electrical
shock hazard, short circuit, or fire.
Keep water from entering inside the unit as this may cause
electrical shock hazard, short circuit, or fire.
How to Store
Maintenance and Inspection
If you will not be using the device for an extended period, clean the main
unit and the attachment before storing.
When not in use, turn off the power, unplug the AC adapter from the wall
socket, and store in a clean, dry location.
Do not use or leave the device near stoves or heaters, under direct
sunlight, in humid places such as the bathroom, or in an unstable place.
Keep this device out of the reach of children.
If you have not used the device for an extended period, inspect it
carefully and check that the device works properly and safely before use.
If there is any evidence of a malfunction, refer to the “Troubleshooting”
section (p.21) before calling for service.
If the device malfunctions, appears damaged, or needs service, please
contact your local distributor.
How to Clean Attachment and Main Unit
Treatment window and cool plate must be cleaned every time after
each treatment.
Clean the main unit regularly to avoid malfunction or operation failure.
Always turn off the power and unplug the AC adapter from the main unit
and from the wall socket before cleaning.
Use a sponge or cloth with diluted mild detergent
for heavy dirt.
Never wipe the device with solvents such as
alcohol, thinner, benzene, or nail polish remover.
Use a wrung cloth to clean dirt from the surface.
Remove finger prints and keep the filter clean. Dirt or debris may
cause the filter to overheat, degrade performance of the flash, lead to
a malfunction, or cause skin irritation.
Remove any dirt or debris from the attachment filter as well.
Remove skin care or hair debris or dirt on the yellow glass
filter with a soft cloth or cotton tip.
Gently remove any skin care product or dirt that may be on the inner
edges of the treatment window opening by using a cotton tip.
Also clean any dirt in the areas of contact between the treatment
head and Face Attachment with a wrung cloth.
Use a wrung cloth to clean dirt, skin care product, or hair
debris from attachment, treatment window, and cool plate.
Cleaning Treatment Window and Face Attachment
Cleaning the Main Unit
After Treatment
After Treatment
After Treatment
Table of contents
