YAW VR Yaw2 User manual

Yaw2 assembly guide and
general help

1. rotation platform 2. base unit 3. design legs 4. pitch platform 5. roll platform 6. side rails
7. seat 8. foot holder 9. footrest plate 10. seat holder slider 11. large gaming plate 12. plate
mounts 13. plate holders
1. metal sheet + 2 x M620 screws
2. counter weight holder
3. 3 x M6x10 screws
4. 4 x M6x16 screws
5. 12 x M6x20 screws
After opening the package check all items were included. If not please contact us.

Tools needed:
Electric screwdriver / screwdriver + M6 screwdriver bit + screwdriver extension

Yaw2 assembly
Written guide
I. Design Leg Assembly
If you have a 3DOF simulator, then
Platform for this step, but if you have the 2DOF version, use the
Base Unit instead of the Rotation Platform here.
Step 1.: Mounting the design legs on the Rotation Platform
Turn the Rotation Platform upside down (if you have built in
be a flat bottom).
Mount the design legs on it. Carefully attach the LED panels on
both sides. Align the predrilled holes.
Step 2.: Tighten the legs with corresponding screws
Find the 4 x M6X16 cylindrical head screws. Take your electrical
screwdriver and screw in the screws on the side of the Rotation
Platform (behind the LED panel). Then turn the Rotation platform
over on its legs

II. Rotation Platform and Base Unit assembly
If you have a 2DOF version, you can skip this step.
Step 3.: Place the Base Unit on the Rotation Platform
On top of the Rotation Platform there are four mechanical
adapters, which connect the Base Unit to the Rotation Platform.
Carefully, place the Base Unit on the Rotation Platform, paying
aligned before tightening the screws.
Step 4.: Tighten the Base Unit with the corresponding screws
Find the 4 x M6X20 countersunk head screws. Take your
screwdriver the screws on the side of the Base Unit.

III. Base Unit and Pitch Platform assembly
Step 5.: Fold out the Flat Cable from the Base Unit
The Flat Cable is folded inside the Base Unit. It is fixed with a tape
that has your local power supply written on it (either 110V or 220V).
Remove the tape and fold out the Flat Cable and leave it hanging
outside the Base Unit for now.
Step 6.: Loosen the fixing casters of the Pitch Platform
On both sides (front and back) of the Base Unit, you will find a pair
of fixing casters. These casters will keep the Pitch Platform in
place. Push the holder of the casters on the inside of the Base Unit
a small piece sticking out of the Base Unit on the front and back.
Step 7.: Place the Pitch Platform on the Base Unit
through the whole part. This rail is going to be between both pairs
of fixing casters. Mount the Pitch Platform on the Base Unit paying

special attention to placing the rails in between the fixing casters.
Also make sure that the Pitch Platform is not sitting on the flat
cable.
Step 8.: Activate the Fixing Casters of the Base Unit
The
sticking out on the front and the back of the Base Unit after you
loosened the fixing casters. Press them firmly to push the casters
back in place.

IV. Pitch and Roll Platform assembly
Step 9.: Align the Roll Platform using the casters (pay attention to
the integrity of the cables)
Check where the cogwheels are on the Roll Platform and where
they are inside of the Pitch Platform. Slide the Roll Platform into
the Pitch Platform from the side. Pay special attention to the
moving it back and forth in the arc.

V. Seat, Footholder and Footrest assembly
Step 10.: Assemble the Footholder with the seat
Turn the seat upside down. Loosen the screws of the seat where
the Footholder will be slid into.
Slide the Footholder into the retainer on the bottom of the seat.
Push it through well over the top (this is how you can adjust the
length of the Footholder).
Tighten the screws. Turn the seat back over.
Step 11.: Assemble the Footrest plate with the Footholder
Remove the 4 screws from the footrest (keep them close though,
you will need them soon).
Attach the footrest plate (use the previously removed screws)
Mount the footrest plate setting it to a desired angle. Place the
screws in the pre-drilled holes. Tighten the screws to secure the
footrest plate.

VI. Seat assembly with Pitch and Roll
Step 12.: Screw the Counterweight Holder in
On the top of the Seat
counterweight. In the middle of the -drilled
hole. Screw in the counterweight holder there.
Step 13.: Fit the seat to the Pitch Platform
When placing the seat on top the already assembled parts, start
with attaching the top of the seat to the Pitch Platform.
Step 14.: Fit the Seat to the Roll Platform

After fitting it to the Pitch Platform it should be easy to fit it in the
Roll Platform. Just lower the seat and it will align perfectly.
Step 15.: Fasten the seat to the Pitch Platform with screws
Fasten the seat to the Pitch Platform with 3 x M6X10 cylindrical
head screws around the point where you attached the two parts.
Step 16.: Fasten the seat to the Roll Platform with screws
Fasten the seat to the Roll Platform with 8 x M6X20 countersunk
head screws.

VII. Chair Holder Slider assembly with Chair
Step 17.: Identify the front of the Chair Holder Slider
If you ordered the Yaw VR chair, the screws will be already in it.
package, therefore you can skip Step 18.
Step 18.: Remove the screws from the bottom of the chair
along the Chair Holder Slider.
Step 19.: Fasten the Chair Holder Slider to the chair (use the screws
you removed in the previous step)
with the sides of the seat. Tighten the screws.

Step 20.: Attach the chair to the seat
Fit the chair with the now attached holder slider on the seat. On
both sides the chair holder slider has 3 anchor points which must
fit perfectly.
Step 21.: Fasten the Chair Holder Slider to the seat
Screw in the one corresponding screw on the front of the Chair
Holder Slider.

VIII. Connecting Flat Cable ports with the Upper Flat PCB
Step 25.: Remove the panel on the back of the Pitch Platform
screws. Remove the screws and take down the panel.
Step 26.: Place the Flat Cable carefully inside the panel
Be extra careful to not break the Flat Cable. Slide it gently under
the horizontal piece and upwards to the PCB.
Step 27.: Connect the Flat Cable Ports to the Upper Flat PCB
Ports are organized in the same pattern as the cable (see below):
Step 28.: Place the metal sheet that clamps the flat cable
Step 29.: Tighten the screws firmly on the metal sheet
Step 30.: Close the panel and fasten with screws
, now you can try your new Yaw2! Have fun! :)