Zhejiang Sansilou Industrial BECS-129S User manual

Index
BECS-129S Singular-head Computerized Embroidery Machine I
Index
Part I Features________________________________________________________________________1
Part II Control Panel and Basic Operations ________________________________________________6
2.1 Control Panel ___________________________________________________________________6
2.2 Main Screen ___________________________________________________________________10
2.3 Definition and Basic Operation of Keys_____________________________________________13
2.4 Indicator Light of Main Shaft Stop Position _________________________________________17
2.5 Start and Stop Button____________________________________________________________17
Part III Basic Knowledge and Operation__________________________________________________18
3.1 Work Status, Embroidery Mode and Work Sequence _________________________________18
3.2 Inputting Design from USB-Disk and Starting First Embroidery________________________21
3.3 Select Memory Design for Embroidery _____________________________________________26
Part IV Setting Parameters_____________________________________________________________29
4.1 Parameter Menu________________________________________________________________29
4.2 Real Time Rotation and Scaling up/down ___________________________________________30
4.3 Setting Repetition Embroidery ____________________________________________________34
4.4 Offset Point____________________________________________________________________38
4.5 Cyclic Embroidery ______________________________________________________________39
4.6 Work Sequence_________________________________________________________________40
4.7 Standard Data Parameter ________________________________________________________42
4.8 Standard Trim Parameters _______________________________________________________45
4.9 Standard Machine Parameters ____________________________________________________47

Index
II BECS-129S Singular-head Computerized Embroidery Machine
4.10 Common Parameters ___________________________________________________________52
Part V Manual Operation ______________________________________________________________54
5.1 Origin Back____________________________________________________________________54
5.2 Stop Back______________________________________________________________________54
5.3 Main Shaft Origin ______________________________________________________________55
5.4 Manual Trim___________________________________________________________________55
5.5 Frame Range___________________________________________________________________55
5.6 Embroider Range_______________________________________________________________57
5.7 Embroider a Line _______________________________________________________________57
5.8 Forward Code Float_____________________________________________________________58
5.9 Backward Code Float____________________________________________________________58
5.10 Forward Sti. Float _____________________________________________________________59
5.11 Backward Sti. Float ____________________________________________________________60
Part VI Disk Management _____________________________________________________________61
6.1 List USB Disk Directory _________________________________________________________61
6.2 U Disk Design Input_____________________________________________________________62
6.3 Des. Output to USB Disk _________________________________________________________65
6.4 Format U Disk _________________________________________________________________67
6.5 Delete USB Disk Design__________________________________________________________68
Part VII Memory Design Operation______________________________________________________69
7.1 Enter the Memory Design Operation Menu _________________________________________69
7.2 Select Design for Embroidery _____________________________________________________70
7.3 Show Memory Design ___________________________________________________________72

Index
BECS-129S Singular-head Computerized Embroidery Machine III
7.4 U. Des. Input___________________________________________________________________73
7.5 Delete Memory Design___________________________________________________________75
7.6 Copy Design ___________________________________________________________________75
7.7 Combine Design ________________________________________________________________77
7.8 Divide Design __________________________________________________________________80
7.9 ClearAll ______________________________________________________________________82
7.10 Check Design _________________________________________________________________83
7.11 Rename File___________________________________________________________________83
7.12 Expand Satin__________________________________________________________________84
7.13 Design letter pattern____________________________________________________________85
Part VIII Assistant Function____________________________________________________________88
8.1 Set soft Limit___________________________________________________________________88
8.2 Frame Restore _________________________________________________________________89
8.3 Default Setup __________________________________________________________________90
8.4 Change UI Language ____________________________________________________________91
8.5 Set Frame Origin _______________________________________________________________91
8.6 Machine Self-Test and Test Machine Parts __________________________________________92
8.7 Set Password___________________________________________________________________92
8.8 Set Network Address ____________________________________________________________93
8.9 LAN Function Switch____________________________________________________________94
8.10 Net Manual Connect ___________________________________________________________95
8.11 Set Design Showing-Color _______________________________________________________96
Appendix ___________________________________________________________________________98

Part I Features
BECS-129S Singular-head Computerized Embroidery Machine 1
Part I Features
Notice: The machine should be grounded with the earth terminal, otherwise the
machine may not work properly or even be damaged.
1. LCD Displayer
This machine model uses LCD as monitor. Both words and icons are used
in the operation window to help fast learning and easy operation. The design
picture can be displayed simultaneously with embroidery.
2. Input and output of Usb disk-stored designs
From the built-in usb port, the user can directly input the designs data in
the following formats into the memory: files in binary system (.dsb), ternary
system (.dst) and Z coding system (.dsz) from Tajima format disk, and files in
binary system, ternary system and Z coding system from Barudan format disk.
And it is also possible to output the design data from the memory to Tajima
format disk in the term of binary format.
3. Storage capacity for design data
The built-in storage can keep 99 designs and the stored maximum stitches
are 1,000,000.
4. Rotating speed control
Press the keys to adjust the current rotating speed of the main shaft between
400 rpm and the highest speed, and the current speed value will show in the
screen.And the highest rotating speed for flat embroidery is 1000 rpm.

Part I Features
BECS-129S Singular-head Computerized Embroidery Machine2
5. Real time scaling up/down and design rotation
While embroidering the designs in memory, the user can scale up/down the
design separately in vertical and horizontal directions within the range of scaling
from 50% to 200%. Meanwhile the user can rotate the design freely in a circle by
choosing one of the eight coordinate directions and adding an angle degree
between 0° and 89°.
6. Thread break detecting
In parameter setting, the user can select thread break detecting or no
thread break detecting. When it’s effective, the machine will stop
automatically and show an icon in the screen when thread breaks.
7. Work sequence
The “work sequence” parameter decides how to deal with color change
codes.
8. Over-frame protection
It’s to prevent the frame from exceeding the normal scope to cause a
collision accident.
9. Auto origin return
With this function, the frame will return to the origin point upon
completion of embroidery.
10. Positioning idling
The frame can move fast forward or backward to the desired position
according to function code or certain stitches to move without embroidering,

Part I Features
BECS-129S Singular-head Computerized Embroidery Machine 3
which will let the machine start embroidery from anywhere.
11. Repetition embroidery function
There can be maximal 99 times of repetition for one design in each of
vertical and horizontal directions.
12. Periphery operation
This is to show and idle around the border of the design which has been
scaled up/down, rotated or repetition embroidered.
13. Scaling up/down and rotating the design
It is to embroider the design in memory after scaling up/down and/or
rotate it.
14. Design operation
With this, the user can survey the memory directory and the information
of design files in the directory. And the user can delete, copy, combine or
divide the designs.
15. USB disk management
It is to list the design files, input/output files and format the USB disk.
16. Error information
In case of wrong operations or machine malfunctions, the screen will
show words or icons to inform you.
17. Frame protection
When the frame has changed its position after power-off during
embroidering or after stopping the machine, it will be unable to continue the

Part I Features
BECS-129S Singular-head Computerized Embroidery Machine4
former embroidery. If the frame protection has already been set as effective,
the user can restore the frame position to continue embroidery via the
operation “Frame restore”.
18. Adjusting the stop position (parameter “Set brake Para”)
It is to adjust the stop position of the main shaft to suit different machines.
The parameter is available to be changed by setting the parameter of flat
embroidery machine in Setting. The bigger its value is, the larger additional
degrees the main shaft will stop with.
19. Returning and patching
When the thread breaks, the user can choose automatic return of a certain
stitches or press the stop button for manual return. When the machine arrives
at the start point for patching, press start button to patch.
The stitches of automatic return can be set.
20. Cyclic embroidery
With this function the machine will automatically return to the origin
point to start again after embroidering one design.
21. Offset point
It’s to set an offset point anywhere away from the start point. This will
facilitate the operations such as fabric-changing and trimming.
22. Change UI Language
Choose the desired language to suit different customers. You can choose
several kinds of language as follows : Chinese , English , Turkish , Spanish

Part I Features
BECS-129S Singular-head Computerized Embroidery Machine 5
and Portuguese.
23. Trimming
In embroidery the user can choose the automatic trimming according to
the function codes or stopping the machine to trim manually.

Part II Control and Basic Operations
BECS-129S Singular-head Computerized Embroidery Machine6
Part II Control Panel and Basic Operations
2.1 Control Panel
LCD Panel