Zomodo KTC011 Installation instructions

ZOMODO.CA
Faucet Installation

Care and Maintenance
In order to ensure proper funcon over the lifeme of the faucet, smoothly
operate the handle and pull-out hand shower during use. When installing do
not over ghten the locking nut. Regularly clean the faucet with a so, damp
cloth and avoid abrasive cleaners, steel wool, and strong chemicals.
Notes
All pipework must be thoroughly flushed prior to installaon as foreign
materials may block the flow .
1.
Aerator and the flow control can be removed with standard tool and
cleaned.
2.
If a screen-filter is fied into the faucet, remove it and flush the pipes
and faucet to remove grit. Then re-insert the screen.
3.
Working Specificaons
Working pressure: 20-100 psi
Working temperature: 1-60°C
This faucet must be installed with isolang/wall valves in accordance with
local installaon codes. All ZOMODO faucets are strongly recommended
to be installed by a licensed plumber. Improper installaon may void the
warranty.
24
16
17
18
19
14
15
8
11
12
13
9
10
4
2
3
5
6
7
23
22
21
20
1
KTC011KTC011
Parts List
4 O-ring
1 Spout
6 Screw
7 Facuet body
9 O-ring
10 Locking Screw
12 Steel washer
11 Plasc washer
13 Plasc locking nut
19 Handle cap
20 Screw
21 Plasc washer
22 Pin lever
16 Cartridge
17 Locking Nut
18 Cover
14 Connecon tube - hot
15 Connecon tube - cold
8 Base
23 Aerator
24 Flexible hose
2 Guide washer
3 Guide sleeve
5 Guide nut
235
362
286

SINK WALL
WALL
Insert the faucet into the countertop and
ensure the O-ring (9) is secure in the groove
of the faucet body. Then slide the washers
(11 and 12) onto the threaded body of the
faucet followed by the nut (13) in the order
shown in the diagram. Tighten the nut (13)
by hand and ensure the faucet is correctly
aligned above the countertop.
Step 3
Locate a hole centre in the countertop at
least 50mm from the wall and with enough
clearance to the rim/flange of the sink.
Dim. A >50mm(2”) and Dim. B >50mm (2”) .
If you need to locate the faucet within these
dimensions, you should ensure enough
clearance for the mounng washers and
nut (11,12,13). Cut a hole 35 to 40mm
diameter into the countertop .
Step 2
Aach the hoses (24) to the Connecon tube
(14,15) and ghten firmly. Do not use thread
tape, as the water-ght seal is provided by
O-rings. Do not over ghten.
Step 1
Note: Use the hose with RED braid-strands
for the hot water connecon. Connect hot
water to the rigid pipe with red marking.
SINK WALL
WALL
A
B
Flush the wall valves to ensure no grit enters
the faucet. Now aach the hoses to the wall
valves ensuring the hose with RED braid
aaches to the hot water outlet.
Step 4
KTC011
HOT COLD
KTC011

SINK WALL
WALL
Test the faucet flow and mix funcons. If
any grit etc has entered the faucet you can
easily remove the aerator(23) and
clean/reaach.
Step 5
KTC011
Troubleshoong
1. If water is leaking from the connecon tube joints (14,15) you should
reghten the flexible hoses (23). It is possible that these connecons
have loosened when the flexible hoses are ghtened to the wall valves.
2. If the water stream is uneven it is possible that debris or grit has blocked
the aerator. You can remove the p of the spout and backflush the aerator.
Firmly reghten the retaining nut.
3. If the faucet is lose or rotang at the base as it enters the countertop you
should reghten the nut (13) ensuring the handle lever assembly is correctly
posioned.
4. If the spout (1) is loose at the connecon to the body (7) you may need to
gently ghten the small grub screw (6). Do not over ghten the grub screw
or the spout will not rotate.