A/DA GroundDrill - 3 User manual
Operating manual
Ground drill
Model: GroundDrill - 3
Manufacturer Address: WWW. ADAINSTRUMENTS.COM
GroundDrill - 3
Table of contents
1. Introduction ........................................................................................................................................................................................3
2. Safety rules and precautions..............................................................................................................................................................3
4. Assembly ..........................................................................................................................................................................................6
6. Motor .................................................................................................................................................................................................9
7. Adjusting the carburetor.....................................................................................................................................................................12
11. Prolonging the life of your machine..................................................................................................................................................14
MEASUREMENT FOUNDATION
GroundDrill - 3
3
DRESS
1. Wear a long-sleeved shirt and long pants closed at the culf.
3. Do not use the auger indoors or in poorly ventilated places. Exhaust is poisonous.
MEASUREMENT FOUNDATION
GroundDrill - 3
4
3. Wipe the auger body dry of any spilled gasoline after refuelling.
6. Store fuel in approved containers only and keep in a cool place.
stable position.
approaches it from the front.
9. Make sure the drill bit has stopped moving before placing on the ground.
MEASUREMENT FOUNDATION
GroundDrill - 3
Engine type: air-cooled, 2 stroke
Displacement: 49 cc
Palm grip
Engine
Drill
Gear case
Throttle lever
MEASUREMENT FOUNDATION
GroundDrill - 3
6
Gear case
Bolt x 3
Engine
Clutch shoe
Stud x 1
- Work open the connector case using a slotted
side to its counterpart on the gear case side.
- Reattach the connector case.
- Set the gear case on the engine and loosely
tighten the stud and nut.
3 holes, then tighten all 4 bolts securely and
evently.
Connector case
AConnector case
Throttle wire
(gear case side)
Throttle wire
(engine side)
Close in this direction
MEASUREMENT FOUNDATION
GroundDrill - 3
7
engine and gear case. Make sure col-
ors are match and connections are se-
curely tight.
the pin out from its hole.
- Align the pin holes on the gear shaft
and drill shank, and insert the drill
over the shaft.
- Reinsert the pin through the pin hole
covered.
Gear shaft
Clip band
Slide the
band
upwards
Drill shank
Pin
Slide the
clip band
downwards
Leads
MEASUREMENT FOUNDATION
GroundDrill - 3
- Do not add oil past the drain plug hole. To determine oil level, stand the auger on the drill. Oil level should be at the bottom of the
drain plug hole.
Gear case
Drain plug hole
Drain plug
Fill oil up to here
MEASUREMENT FOUNDATION
GroundDrill - 3
9
MOTOR
2-stroke oil. .
Caution: If you use an incorrect mixture of gaso-
line and oil, the engine may be damaged.
Zipper
Throttle cable adjustment screw
2. START
- Pump primer ball on bottom of carburetor about
- Move choke lever up for cold starts to block air
try again.
Throttle lever
Main On/Off switch
MEASUREMENT FOUNDATION
GroundDrill - 3
Primer ball
Choke lever
Pull start
- Make sure that throttle is set to idle.
The primer ball pumps gas through carburetor and back into the gas tank. It is not possible to over-prime the carburetor.
3. OPERATION
- Press or release throttle lever to get desired rpms.
MEASUREMENT FOUNDATION
11
GroundDrill - 3
- Release throttle to idle speed.
When storing for long periods, remove all fuel from the
gas tank and then start the engine to use up all the fuel in the
carburetor.
against the tank cap for long periods. The pressure inside the tank
can cause the gas to spill out from the vent in the cap.
Main On/Off switch
Throttle lever
MEASUREMENT FOUNDATION
12
GroundDrill - 3
: Generally it is not necessary to adjust the carburetor as
the motor is set at factory to the best position. Incorrect mix-
ture adjustment can cause damage to the machine or operator.
1) Idle adjustment screw
2) Low speed fuel mixture screw
3) High speed fuel mixture screw
MEASUREMENT FOUNDATION
13
GroundDrill - 3
Check tightness of all screws/bolts
Cover
Element
MEASUREMENT FOUNDATION
14
GroundDrill - 3
When storing for more than a month:
- Drain the fuel tank and start the motor to burn any remaining fuel
-
move fuel from the tank and carburetor before storing.
MEASUREMENT FOUNDATION
GroundDrill - 3
if it has been misused, abused or altered. Withiut limiting the foregoing, leakage of the battery, bending or dropping the unit are
presumed to be defects resulting from misuse or abuse.
The manufacturer, or its representatives, assumes no responsibility of results of a faulty or intentional usage or misuse including any
of data and interruption of business etc., caused by using the product or an unusable product.
-
2. Periodic maintenance, repair or changing parts as a result of their normal runout.
-
4. Service by anyone other than an authorized service center.
instruction.
-
WARRANTY CARD
Name and model of the product ________________________________________________
Serial number ________________date of sale_______________________
Name of commercial organization _____________________stamp of commercial organization
Warranty period for the instrument explotation is 24 months after the date of original retail purchase. It extends to the equipment, imported
During this warranty period the owner of the product has the right for free repair of his instrument in case of manufacturing defects.
occur in the result of the instrument outage.
The product is received in the state of operability, without any visible damages, in full completeness. It is tested in my presence. I have no
complaints to the product quality. I am familiar with the conditions of qarranty service and i agree.
purchaser signature _______________________________
Before operating you should read service instruction!
If you have any questions about the warranty service and technical support contact seller of this product
__________________________________________________________________________
__________________________________________________________________________
name and model of the instrument
Corresponds to ______________________________________________________________
designation of standard and technical requirements
Data of issue _______________________________________________________________
Stamp of quality control department
Price
Sold ___________________________________ Date of sale ______________________
name of commercial establishment
GroundDrill - 3
Table of contents
Other A/DA Drill manuals
Popular Drill manuals by other brands
Baukraft
Baukraft BK-BRH58 user manual
Clarke
Clarke CONTRACTOR CON400RHD Operation & maintenance instructions
Hougen
Hougen HMD115 Series Operator's manual
Panasonic
Panasonic EY6803 - HAMMER DRILL DRIVER 12V operating instructions
Meec tools
Meec tools 254-013 Operating instructions in original
Echo
Echo ED-2000 Operator's manual
Chicago Electric
Chicago Electric Chicago 44849 Assembly information
Ironton
Ironton 46179 owner's manual
Matco Tools
Matco Tools MT1810 operating instructions
Westfalia
Westfalia 77 49 01 instruction manual
Chicago Pneumatic
Chicago Pneumatic CP8548 manual
Chicago Pneumatic
Chicago Pneumatic CP879C Operator's manual