A-EON 1702 User manual

AEON-1702 - Page 1
Premium Speaker Stand
Instruction Manual
Tools Required:
- None
Parts Included
- Upper bar with Speaker Holder
- Lower bar with Bar Connector
- Stand Base
- 3pcs Rubber Pads
- 4pcs Lower Bar Washer
IMPORTANT NOTE:
Please read the instructions completely
before attempting assembly. Failure to comply
to the instructions may result in an unstable stand
that can topple or fall over, damaging your speaker.
!
SIZE AND WEIGHT RESTRICTIONS:
The AEON-1702 Speaker Stand is built to
specifically to hold the SLS Q-Line type speakers.
!
Parts List:
Figure A
Complete Installation
Overview
A: Stand Base
B: Upper Bar
with Speaker Holder
C: Lower Bar with
Bar Connector
Other Required Parts:
- Speaker Wire
- SLS Q-Line Speaker
D: Lower Bar Washer

Figure E:
Bottom Washer
Placement
AEON-1702 - Page 2
Premium Speaker Stand
Instruction Manual
INSTALLATION STEPS
1) Remove all components from carton and unwrap the protective bags.
2) See page one of this manual for a parts list of all parts included in the carton.
Familiarize yourself with each part and their corresponding letter. Use Figure A on
page one as a guide for the overall completed assembly.
3) Place a rubber pad on each of the three feet of the Stand Base (A) as shown in
Figure D.
4) Thread the Lower Bar Washer (D) onto the Lower Bar (C) as shown in Figure C
on to each Lower Bar.
5) Attach the Lower Bar (C) to the Stand Base (A) by inserting the Lower Bar into the
hole on the Stand Base and turning clockwise.
6) Turn the Lower Bar Washer (D) counter clockwise until it is tight onto the Stand
Base (A). The washer should be finger tight, and a pair of pliers should not be used.
7) Attach another Lower Bar Washer (D) to the underside of the Stand Base (A) and
finger tighten until it will not move. See figure E.
8) Insert the Upper Bar (B) into the Lower Bar (C) through the bar connector. When
you have inserted the Upper Bar to a desired height, twist the bar connector
clockwise until it is tight. The Upper Bar should not move up or down after the bar
connector is tightened. See Figure F.
9) Place the speaker stand assembly near the desired location that you want. Slide
your speaker wire into the hole under the Stand Base (A) through the Lower Bar (C)
and push the speaker wire until it appears at the top of the Upper Bar. Grab the wire
with your hands and pull until you have a few feet of speaker wire hanging out of the
top.
10) Match the holes on the back of your speaker with the Top Base Assembly (see
Figure B) and press into place. Press firmly to ensure a good fit.
11) Finish the completed assembly by hooking up your speaker with the speaker
wire. Your finished assembly should look like Figure A on page one.
Figure B:
Top Base
Assembly
Figure D:
Rubber Pad
Placement
Figure F:
Upper and Lower
Bar Connector
Do not over tighten
NOTES
The height of the Upper Bar is adjustable. Simply loosen the Bar Connector on the
Lower Bar by turning it counter clockwise. This will free the Upper Bar to move up
and down. Set to the desired height and tighten the Bar Connector again by turning
it clockwise by hand. Be careful not to over tighten the Bar Connector of you may
damage the stand.
If you are using this speaker stand for an SLS Q-Line style speaker, please note that
there are four different positions that you can mount your speaker to the stand.
Each position has a pair of slots on the back of the speaker for easy placement.
Figure C:
Attach Washer
to Lower Bar
WARNING
Be careful not over tighten the Upper and Lower Bar Connector. The connector
should only be slightly tight on the bar to prevent the Upper Bar from sliding. If
you over tighten the connector, or use a tool to tighten, you could break the
connector.