Aban Technology HIGH SPEED DOME CAMERA User manual

User Manual
27X AF Zoom
HIGH SPEED DOME CAMERA

2

3
Ⅰ CAUTION --------- 4
Ⅱ INTRODUCTION OF PRODUCTS --------- 6
Ⅲ DIRECTIONS FOR USE --------- 14
Ⅳ FUNCTIONAL SETTING BY THE KEYBOARD --------- 26
Ⅴ OSD MESSAGE DISCRIPTION --------- 29
Ⅵ TROUBLE SHOOTING --------- 31
Ⅶ DIMENSION --------- 33
Ⅷ ASSEMBLY --------- 35
Ⅸ SPECIFICATION --------- 38
Table of contents

4
Thank you for purchasing our product. Please operate the product after being
fully aware of the manual. Pease contact us if you have any queries.
Precaution
Note the following matters before the installation of the product.
Avoid the following places for the installation.
Ⅰ. CAUTION
A high/low temperature: Using indoor-cameras
in the places of +50°C~ -10°C can cause
troubles and lower its capacity.
Snow, rain and wet: Humidity or water and
any liquid inside-camera can cause troubles.
Oil, gas: Oil and gas can damage the camera
as they go through the cameras.
Vibration, shock: They bring on problems or
errors of the camera.
Direct light, exposure to the air: In the case of
that sets indoor- cameras outside where the
weather is changeable, it can cause problems.
Closing to High frequency and electric power
lines: Setting the camera up around
electromagnetic units or power supplier can
bl

5
Caution in Use
Do not disassemble the unit and put alien substances in the unit.
- Disassembling the unit or putting alien substances such as a metal can make the
camera defective.
- Make sure of power switch-off before the installation.
: Ensure power switch-off and check the voltage the camera before the installation.
- Do not give the unit a shock and an operation.
: Giving a strong shock or an excessive power on the button, terminal can cause
problem.
This product has been designed and manufactured in accordance with the harmonized
European standards, following the provisions of the below stated directives.
Electromagnetic Compatibility Directive 89/336/EEC
(EN60065:1998, EN61000-6-3:2001, EN61000-6-1:1997)
This devise complies with part 15 of the FCC rules operation is subject to the
following two conditions: (1) This device may not cause harmful interference and
(2) This device must accept any interference received including interference that
may cause undesired operation
Caution :
①Must use AC24V power source, current intensity must be less than 1.5A and
must use a double winding transformer
②Never extend the power line from adaptor to camera.
③ Please use more thick cable than 18AWG(1.0mm), if you want to
extend the power line.
④ You must use one adaptor per one camera that is being provided.
⑤ Use extra power supplier, If you want to supply many piece of
cameras.

6
1. DESCRIPTION AND FEATURES
Description
This camera has been designed elegantly for buildings, department stores that
need to be in harmony with the interior as a high speed dome camera, including
various observation functions.
Features
☺Optical 27X Zoom Rate
Built-in 27X Zoom Camera with 12x Digital Zoom (Total 324x Zoom )
☺A low light function
Surveillance with optimum picture is possible owing to digital-slow-shutter function.
Digital-slow-shutter function is improving the CCD sensitivity by electrically lengthening
exposure time so that it should be under surveillance on the condition of 0.00005Lux in
B/W
☺Digital Noise Reduction
DNR significantly reduces the amount of low luminance noise.
☺Digital Image Stabilize
There is some tremble as zoom magnification is high, the function can compensate the
tremble.
☺HLC/User BLC Function
The HLC settings selectively eliminates high lights in a limited.
☺Auto Tilt Function
The unit can track the moving object automatically until 180° in vertical by using controller.
☺250 Preset positions
A maximum of 250 preset positions can be programmed. The preset function enables to
set where you want on monitor at any time.
☺Various auto-surveillance functions
Swing(2), Group(12 Presets), Tour(12 Groups), Spiral, Trace
☺Smart pan/tilt function
Pan and tilt speed compensation function in proportion to depth of zoom.
Ⅱ. INTRODUCTION OF PRODUCT

7
2. INSTALLATION AND CONNECTION
1) Name and function of each part
(UPPER COVER)
The camera’s body goes to
here and a power cable,
data cable, video cable,
sensor have been
connected with this
(DOME DRIVER)
A main body that has a
built-in the control units and
camera
(LOWER COVER)
Insert the body into the
upper cover, then close the
lower cover
Indoor Type Outdoor Type

8
2) Installation
SEPARATION OF LOWER
COVER
(Indoor type)
Loosen the bolt of the back
of lower cover by a
screwdriver(+), then turn the
cover as above the picture
and pull the lower cover to
the down
(Outdoor type)
Loosen the four bolts of the
lower cover, then separate.
Loosen the three bolts, the
round head shaped, of the
camera body. The three bolts
are not loosened completely
and not come up more than
1cm of the lower cover, then
separate.
Pull the cover up with
grabbing the bottom of the
camera after loosening the
three bolts
Indoor Type Outdoor Type

9
Open the connector cover, then connect
power, data, video cable and sensor
The cover is opened if user loosens the
one bolt on the connector cover by using a
screwdriver(+).
The bolts not loosened completely to
protect from missing of them.
Be careful that each cable which each
function is changed wrong
Have you connect the power cable
in the right direction ?
If yes
①RED led, in the middle of the
connector, is lighted
②Use AC24V power source and
user can use any power input that is
connected with a terminal and a
jack (But use 1 input).

10
3) How to connect equipments
Connect the image
line of a monitor
User can control maximum up to 255 cameras
connected by using the exclusive control keyboard.
User can connect it maximum up to 1.2km when
using twist pair shield cable as a connecting cable
DC12V/1A adaptor and junction box are provided
on a purchase, Junction box consists of 2 data
ports ( Each data port can be connected with
maximum up to 128 cameras and sub keyboard
terminal
Reference to the following page.

11
Alarm output is tangency output of
relay non-load, it can be used up
to AC220/10A by connecting the
load. The switch is automatically
turned on when the sensor works
and it is possible to cancel by
using the controller after a limited
time The sensor
Can be connected maximum 4 channels and the camera
can be moved automatically to the point by preset mode,
DATA
Can be processed by RS485 or RS422 and use parallel connection to use a large quantity of
cameras. ( Even if it must be used 2-twist paired cable in use of RS422, the terminal port
which was connected with R485 cable port with 1-pair cable when it is not necessary to take
a return data from camera

12
4) HOW TO SET PROTOCOL
①Please the power off
②Switch protocol that user wants to change on as above the cable
③The power on, then the set protocol and baud rate are appealed.
④The power off, if every setting is right. Then the change of protocol is finished.
⑤Change No. 3 of S2 to ADDR before the power on, then the power on after setting the address of the camera.
⑥Try it again with the information as above the table, if something is wrong
PROTOCOL S 1 S 2
SW 1 SW 2 SW 3 SW 7 SW 8 SW ‘INITADDR’
D-MAX (9600
bps) OFF OFF OFF OFF OFF INIT
P-P (9600 bps) ON OFF OFF OFF OFF INIT
P-P (4800 bps) ON OFF OFF OFF ON INIT
P-P (2400 bps) ON OFF OFF ON OFF INIT
P-D (9600 bps) OFF ON OFF OFF OFF INIT
P-D (4800 bps) OFF ON OFF OFF ON INIT
P-D (2400 bps) OFF ON OFF ON OFF INIT
S-T (9600bps) OFF OFF ON OFF OFF INIT
You have to change this switch when you
change protocol
1 2 3 4 5 6 7 8
O
N
4
2
2
I
N
I
P
A
L
I
N
T
ON
OFF
A D D R E S S
T
M
4
8
A
D
N
T
E
X
O
O
F
S 1
Change No.3 of S2 to INIT if user
wants to change protocol
Use to change this switch Protocol
and communication speed
The switch to select
protocol
The switch to select
baud rate

13
5) SETTING ADDRESS OF DIP SWITCHES.
RX
NO
DIP SWITCH (HEX) RX
NO
DIP SWITCH (HEX)
1 2 3 4 5 6 7 1 2 3 4 5 6 7
1 ON OFF OFF OFF OFF OFF OFF 33 ON OFF OFF OFF OFF ON OFF
2 OFF ON OFF OFF OFF OFF OFF 34 OFF ON OFF OFF OFF ON OFF
3 ON ON OFF OFF OFF OFF OFF 35 ON ON OFF OFF OFF ON OFF
4 OFF OFF ON OFF OFF OFF OFF 36 OFF OFF ON OFF OFF ON OFF
5 ON OFF ON OFF OFF OFF OFF 37 ON OFF ON OFF OFF ON OFF
6 OFF ON ON OFF OFF OFF OFF 38 OFF ON ON OFF OFF ON OFF
7 ON ON ON OFF OFF OFF OFF 39 ON ON ON OFF OFF ON OFF
8 OFF OFF OFF ON OFF OFF OFF 40 OFF OFF OFF ON OFF ON OFF
9 ON OFF OFF ON OFF OFF OFF 41 ON OFF OFF ON OFF ON OFF
10 OFF ON OFF ON OFF OFF OFF 42 OFF ON OFF ON OFF ON OFF
11 ON ON OFF ON OFF OFF OFF 43 ON ON OFF ON OFF ON OFF
12 OFF OFF ON ON OFF OFF OFF 44 OFF OFF ON ON OFF ON OFF
13 ON OFF ON ON OFF OFF OFF 45 ON OFF ON ON OFF ON OFF
14 OFF ON ON ON OFF OFF OFF 46 OFF ON ON ON OFF ON OFF
15 ON ON ON ON OFF OFF OFF 47 ON ON ON ON OFF ON OFF
16 OFF OFF OFF OFF ON OFF OFF 48 OFF OFF OFF OFF ON ON OFF
17 ON OFF OFF OFF ON OFF OFF 49 ON OFF OFF OFF ON ON OFF
18 OFF ON OFF OFF ON OFF OFF 50 OFF ON OFF OFF ON ON OFF
19 ON ON OFF OFF ON OFF OFF 51 ON ON OFF OFF ON ON OFF
20 OFF OFF ON OFF ON OFF OFF 52 OFF OFF ON OFF ON ON OFF
21 ON OFF ON OFF ON OFF OFF 53 ON OFF ON OFF ON ON OFF
22 OFF ON ON OFF ON OFF OFF 54 OFF ON ON OFF ON ON OFF
23 ON ON ON OFF ON OFF OFF 55 ON ON ON OFF ON ON OFF
24 OFF OFF OFF ON ON OFF OFF 56 OFF OFF OFF ON ON ON OFF
25 ON OFF OFF ON ON OFF OFF 57 ON OFF OFF ON ON ON OFF
26 OFF ON OFF ON ON OFF OFF 58 OFF ON OFF ON ON ON OFF
27 ON ON OFF ON ON OFF OFF 59 ON ON OFF ON ON ON OFF
28 OFF OFF ON ON ON OFF OFF 60 OFF OFF ON ON ON ON OFF
29 ON OFF ON ON ON OFF OFF 61 ON OFF ON ON ON ON OFF
30 OFF ON ON ON ON OFF OFF 62 OFF ON ON ON ON ON OFF
31 ON ON ON ON ON OFF OFF 63 ON ON ON ON ON ON OFF
32 OFF OFF OFF OFF OFF ON OFF 64 OFF OFF OFF OFF OFF OFF ON
-No.1 is changed to No.64 and the last No.64 is changed No.128 when No.7 DIP SW is on.
-No.1 is changed to No.129 when No.7 DIP SW is off and No.8 DIP SW is on.
-No.1 is changed to No.193 and user can set up to maximum 255 ADDRESS when No.7, 8 DIP SW are on.

14
●OSD (ON SCREEN DISPLAY) menu control
It is the function to call up the Menu
＊User can not only set Preset, Group, Tour, Swing, Trace functions of the camera up by the menu, but also set
them up by shortening keys.
●Accessing OSD menu
●The menu is displayed on the screen with the key tone when user presses No.1 and menu key.
●OSD Menu Control Up, Down, Right and Left moving
of Cursor like under pictures
●Cancellation of OSD menu
◄◄ CAMERA SET UP p1 ►►
1.IDSet :CAM-001
2.OSDDisplay. :ON
3.H-VReverse. :OFF
4.AGClevel. :20dB
5. Shutter speed. : AUTO
6. Sharpness level : 010
7. Brightness : 50
8.Flickerless :OFF
9.SSNR. :Middle
- NEXT MENU PAGE
Ⅲ. DIRECTIONS FOR USE

15
1. ID SET.
This function is to set
camera ID up to 16
letters on the monitor.
User can choose letters
that they want, if user
control a joystick up /
down / right / left, and
user can reselect the
previous letters, if user
presses Z/I, Z/O or turn the head of the joystick to right/left
2. OSD DISPLAY.
Set up whether user sets ID and STATUS to display on the
screen in normal operating.
●ID + Status: ‘ID’ and ‘Status’ displayed on the screen
●ID only: Only ‘ID’ displayed on the screen
●Status only: Only ‘Status’ displayed on the screen
●All off: Nothing displayed on the screen
3. H-V REVERSE
Set up H-V reverse mode.
●Normal
●H-REV : You can flip the picture horizontally on the screen.
●V-REV : You can flip the picture vertically on the screen.
●HV-REV : You can flip the picture horizontally and vertically on the
screen.
4. AGC LEVEL
AGC(Automatic Gain Control)- It adjusts the amount of video
amplification to maintain a full 1-volt peak-to-peak video signal output
automatically.
▶Low, Medium, Max
◄◄ CAMERA SETUP p1 ►►
1.IDSet :CAM-001
2.OSDDisplay. :ON
3.H-VReverse. :Normal
4.AGClevel. :Low
5. Shutter speed. : AUTO
6. Sharpness level : 010
7. Brightness : 50
8.Flickerless :OFF
9.DNRControl :Medium
- NEXT MENU PAGE
◄◄ CAMERA SETUP p1 ►►
1.IDSet :CAM-001
2.OSDDisplay. :ON
3.H-VReverse. :Normal
4.AGClevel. :Low
5. Shutter speed. : AUTO
6. Sharpness level : 010
7. Brightness : 50
8.Flickerless :OFF
9.DNRControl :Medium
- NEXT MENU PAGE
◄◄ CAMERA SETUP p1 ►►
1.IDSet :CAM-001
2.OSDDisplay. :ON
3.H-VReverse. :Normal
4.AGClevel. :Low
5. Shutter speed. : AUTO
6. Sharpness level : 010
7. Brightness : 50
8.Flickerless :OFF
9.DNRControl :Medium
- NEXT MENU PAGE
◄◄ CAMERA SETUP p1 ►►
1.IDSet :CAM-001
2.OSDDisplay. :ON
3.H-VReverse. :Normal
4.AGClevel. :Low
5. Shutter speed. : AUTO
6. Sharpness level : 010
7. Brightness : 50
8.Flickerless :OFF
9.DNRControl :Medium
- NEXT MENU PAGE

16
5. SHUTTER SPEED
As a setting shutter speed mode, it can be distinguished a fast
moving subject easily by means of shutter speed up.
※Attention-The illumination of the camera decreases if shutter
speed is up.
※The state of first default is ‘AUTO’.
※It can be worked in the state of Flickerless ‘off’
▶Range : Auto, 1/125, 1/150, 1/200, --- 1/10000
6. SHARPNESS LEVEL
Compensation of the shape of a subject
▶Range : 0 ~ 14, Default : 10
7. BRIGHTNESS
Control brightness of a screen.
The screen gets dark because an iris is closed as the numerical
value is low, whereas the screen gets bright because an iris
is opened as the numerical value is high.
▶Range: 0~99, Default: 50
8. FLICKERLESS
Tremble on the screen is removed in the state of FLICKERLESS ‘ON’,
the shutter speed, at the same time, is fixed in 1/120sec in NTSC and
in 1/100sec in PAL.
◄◄ CAMERA SETUP p1 ►►
1.IDSet :CAM-001
2.OSDDisplay. :ON
3.H-VReverse. :Normal
4.AGClevel. :Low
5.Shutterspeed. :AUTO
6. Sharpness level : 010
7. Brightness : 50
8.Flickerless :OFF
9.DNRControl :Medium
-
NEXT MENU PAGE
◄◄ CAMERA SETUP p1 ►►
1.IDSet :CAM-001
2.OSDDisplay. :ON
3.H-VReverse. :Normal
4.AGClevel. :Low
5. Shutter speed. : AUTO
6. Sharpness level : 010
7. Brightness : 50
8.Flickerless :OFF
9.DNRControl :Medium
- NEXT MENU PAGE
◄◄ CAMERA SETUP p1 ►►
1.IDSet :CAM-001
2.OSDDisplay. :ON
3.H-VReverse. :Normal
4.AGClevel. :Low
5. Shutter speed. : AUTO
6. Sharpness level : 010
7.Brightness : 50
8.Flickerless :OFF
9.DNRControl :Medium
- NEXT MENU PAGE
◄◄ CAMERA SETUP p1 ►►
1.IDSet :CAM-001
2.OSDDisplay. :ON
3.H-VReverse. :Normal
4.AGClevel. :Low
5. Shutter speed. : AUTO
6. Sharpness level : 010
7. Brightness : 50
8. Flickerless : OFF
9.DNRControl :Medium
- NEXT MENU PAGE

17
9. DNR Control
It can remarkably reduce noise of minimum illumination by super
noise removable technique and also file size becomes smaller while
DVR is being recorded by the effective reduction of noise.
▶Off, Low, Medium, Max
10. BACK LIGHT
This camera is designed so that it delivers a distinctive subject and
background at the same time, even when the subject is in backlight,
unlike conventional cameras, by adopting a proprietary DSP chip.
.Please select a suitable mode below them (The Set Back Light Mode
will be automatically changed by the selection)
▶Off, HLC MODE, BLC MODE
BLC : Enables a user to directly select a desired area from a picture,
and to view the area more clearly.
HLC(High Light Compensation) : If there is a high light installed in dark environment such as an apartment
parking garage or gas station entrance, removing the high light makes it possible to view car license plates
efficiently
OFF : Deactivates the BACKLIGHT function.
11. SET BACK LIGHT MODE
▶HLC(High Light Compensation)MODE
- Limit: Adjust the HLC Sensitivity by selecting Low or Max
- Level: Adjust the WDR Brightness by controlling 1~10.
- This Function only operate in nighttime
▶BLC MODE : Select BLC mode or BLC Set area mode by using
the joystick.
- BLC Level: Adjust the BLC Sensitivity by selecting Low or Max
- BLC Set AREA (Press F/F): Set BLC area location and size
- Select F/F button, and set the BLC area by using the joystick, and set are size by using Z/I, Z/O buttons.
(The monitor shows as Exit BLC set(Press F/N)
After complete all setup, press F/N button, and then move to RETURN MENU PAGE. It is automatically saved.
◄◄ CAMERA SETUP p1 ►►
1.IDSet :CAM-001
2.OSDDisplay. :ON
3.H-VReverse. :Normal
4.AGClevel. :Low
5. Shutter speed. : AUTO
6. Sharpness level : 010
7. Brightness : 50
8.Flickerless :OFF
9.DNRControl :Medium
- NEXT MENU PAGE
◄◄ CAMERA SETUP p2 ►►
10.BackLight :off
11. Set Back Light Mode
12. White Balance : Outdoor
13.FocusMode :Oneshot
14. Zoom Max Limit : 00X
15. DSS Control : 2 Field
16.Day&Night :Auto
17.StabilizeOn/Off :Off
- PREV MENU PAGE
- NEXT MENU PAGE
◄◄ CAMERA SETUP p2 ►►
10.BackLight :off
11. Set Back Light Mode
12. White Balance : Outdoor
13.FocusMode :Oneshot
14. Zoom Max Limit : 00X
15. DSS Control : 2 Field
16.Day&Night :Auto
17.StabilizeOn/Off :Off
- PREV MENU PAGE
- NEXT MENU PAGE

18
12. WHITE BALANCE
It prevents from that white color is changed as illumination, user can
set it up in 2 ways.
▶ Indoor, Outdoor
13. FOCUS MODE
Change Focus Mode to hand-worked or auto.
▶OneShot : Auto Focusing mode works during non-working
after zoom is worked.
▶Auto : It adjusts the focus automatically as it monitors the
screen.
▶Manual : User can control the focus by hand-worked.
14. ZOOM MAX Limit
It is used when user corrects and limits the extensional range
of the focus as a function to set the maximum value of zoom.
▶Off,
27x zoom : 54X ~ 444X
15. DSS CONTROL
An object becomes clear as the field value gets higher in
illumination, whereas a moving object becomes dim.
▶Range : Off, 2 ~ 256 fields
◄◄ CAMERA SETUP p2 ►►
10.BackLight :off
11. Set Back Light Mode
12. White Balance : Outdoor
13.FocusMode :Oneshot
14. Zoom Max Limit : 00X
15. DSS Control : 2 Field
16.Day&Night :Auto
17.StabilizeOn/Off :Off
- PREV MENU PAGE
- NEXT MENU PAGE
◄◄ CAMERA SETUP p2 ►►
10.BackLight :off
11. Set Back Light Mode
12. White Balance : Outdoor
13.FocusMode :Oneshot
14. Zoom Max Limit : 00X
15. DSS Control : 2 Field
16.Day&Night :Auto
17.StabilizeOn/Off :Off
- PREV MENU PAGE
- NEXT MENU PAGE
◄◄ CAMERA SETUP p2 ►►
10.BackLight :off
11. Set Back Light Mode
12. White Balance : Outdoor
13.FocusMode :Oneshot
14. Zoom Max Limit : 54X
15. DSS Control : 2 Field
16.Day&Night :Auto
17.StabilizeOn/Off :Off
- PREV MENU PAGE
- NEXT MENU PAGE
◄◄ CAMERA SETUP p2 ►►
10.BackLight :off
11. Set Back Light Mode
12. White Balance : Outdoor
13.FocusMode :Oneshot
14. Zoom Max Limit :00X
15.DSSControl :2Field
16.Day&Night :Auto
17.StabilizeOn/Off :Off
- PREV MENU PAGE
- NEXT MENU PAGE

19
16. DAY& NIGHT
The function is used to distinguish an object clearly in the dark
condition.
▶ Auto-Low : This mode is worked automatically according to
sensitivity, if the sensitivity is low
▶ Auto-Hi : This mode is worked automatically according to
sensitivity, if the sensitivity is high.
▶ On : Change into DAY & NIGHTY mode by hand-worked
▶ Off : Set DAY & NIGHTY mode ‘off’
17. STABILIZE On/Off
There is some tremble as zoom magnification is high, the function
can compensate the tremble.
▶On / Off
18. SELECT ALARM
Tremble on the screen is removed in the state of FLICKERLESS
‘ON’, the shutter speed, at the same time, is fixed in 1/120sec in
NTSC and in 1/100sec in PAL.
Alarm CH On/Off Page
19. Motion Detection
Set Motion ‘On’ after move the camera where user wants.
It displays the message ‘Motion Detected’ on the screen
when the moving of an object is sensed on the same screen.
◄◄ CAMERA SETUP p2 ►►
10.BackLight :off
11. Set Back Light Mode
12. White Balance : Outdoor
13.FocusMode :Oneshot
14. Zoom Max Limit : 00X
15. DSS Control : 2 Field
16.Day&Night :Auto-Low
17.StabilizeOn/Off :Off
- PREV MENU PAGE
- NEXT MENU PAGE
◄◄ CAMERA SETUP p2 ►►
10.BackLight :off
11. Set Back Light Mode
12. White Balance : Outdoor
13.FocusMode :Oneshot
14. Zoom Max Limit : 00X
15. DSS Control : 2 Field
16. Day&Night : Auto-Low
17. Stabilize On/Off : Off
- PREV MENU PAGE
- NEXT MENU PAGE
◄◄ CAMERA SETUP p2 ►►
18. Select Alarm : Sensor
19. Motion Detection : Off
20. Preset Set & Run Page
21.Trace Set Page
22. Alarm CH On/Off Page
23. Alarm Preset Set Page
- PREV MENU PAGE
- NEXT MENU PAGE
◄◄ CAMERA SETUP p2 ►►
18.SelectAlarm :Sensor
19. Motion Detection : Off
20. Preset Set & Run Page
21.Trace Set Page
22. Alarm CH On/Off Page
23. Alarm Preset Set Page
- PREV MENU PAGE
- NEXT MENU PAGE

20
20. PRESET SET & RUN PAGE
It is a function to set and operate Preset, Group, Tour.
User can see the screen when moves the joystick to Right/Left after
fixing the cursor on the menu.
<<PRESET SETUP PAGE>>
①Preset set CH :
User can set Preset No. and title on this menu.
- Preset No. set : Set it by moving the joystick to Right/Left
- Preset title set : User can see the menu “SET ID” when
press F/F key after setting Preset No
.
•[SAVE]: Previous screen. [DELETE]: Remove. [ESC]: Cancel
◄◄ CAMERA SETUP p2 ►►
18.SelectAlarm :Sensor
19. Motion Detection : Off
20. Preset Set & Run Page
21.Trace Set Page
22. Alarm CH On/Off Page
23. Alarm Preset Set Page
- PREV MENU PAGE
- NEXT MENU PAGE
② Preset PTZ set : Set the position of Preset
Select the main menu with the joystick, then
press F/F key for next page.
Select [SAVE] with F/N key after setting the
Preset point by using the joystick and. In/Out
function, then the data is saved if user
presses F/F key, then it is moved to the
previous screen automatically from the menu
※ Repeat the same way after changing the
number of Preset, if user set another Preset