Abtus PWR-DA09C/P User manual

SPECIFICATIONS
ABtUS SINGAPORE PTE LTD www.abtussingapore.com
Model: PWR-DA09C/P & PWR-DA09C/PG
Sequenced Output
Power Conditioner
PRODUCT DESCRIPTION
The PWR-DA09C/P (10 amp) and PWR-DA09C/PG (16 amp) is a safe and convenient Sequenced
Output Power Conditioner distribution unit offering protection to all valuable rack-mounted equipments.
Sequenced power up of a complete power audio system from just a push of a switch, eliminating
the loud “POP”s which may damage speakers and other equipments connected.
The PWR-DA09C/P (10 amp) and PWR-DA09C/PG (16 amp) features sequenced power start up.
During start up, each outlet is turned on one at a time with a delay time (Variable and programmable)
between each other.
This delay prevents the “POPs” by allowing each piece of equipment to properly power up before
allowing the audio signals to pass through. The PWR-DA09C/P also features an EMI filter which
suppresses RF (radio frequency) and other AC line noises, ensuing a quieter operation of units
that’s plugged in. The Line Voltage sensor monitors the incoming voltage from 185~265VAC,
assuring the AC voltage is in a safe operating range for the connected equipment. Its 12VDC
BNC outlet also allows power for a LED light/Lamp that provides a cool-running light source for
all the equipments in your rack.
** For detail, updated Command Code and Application Software, please visit and download from www.abtussingapore.com
* Specifications are subject to changes without notice.
(8 Delay + 1 )
Typical Applications
Any professional audio
system in powering a rack
full of equipments in
sequence order with a timed
delays.
• Schools (Media Classroom)
• Churches
• Corporate Applications
(Meeting Room)
Technical PWR-DA09C/P (10Amp) PWR-DA09C/PG (16Amp)
Max Current Rating: 10 Amp (2400 Watts at 240 VAC) 16 Amp (3840 Watts at 240 VAC)
Input Voltage: 185 to 275 VAC without damage
Delay Intervals: Total elapsed ON delay time adjustable from 1-60 seconds,
with RS-232 for precise timing and sequence order.
ON Sequence: Respective relay goes ON base on programmed sequence/order and
delay time for each relay.
Remote Switch: Screw type terminal block,
LED, Switch and GND
Spike Protection Modes: Line to neutral, zero ground leakage
Spike Clamping Voltage: 188 Vpk @ 3,000 amps, (133 VAC RMS)
Response Time: 1 nanosecond
Maximum Surge Current: 6,500 amps
Relay Rating 30Amps @ 240VAC
Power Consumption 4.5 Watts (standby), 14 Watts (all relay ON)
Weight 3.6Kg
Over Voltage Shut Down 150V ±1% (Low), 275 ±1% (High)
Operational 220/240V
Mechanical
Housing Metal enclosure
Product
Dimensions (L x W x H) 430 x 204 x 44 mm
Weight 1.35Kg
Fixedness Standard 1-U rack-mount (*with “L” bracket)
Package include
1 x Switcher 1 x RS-232
1 x Power Cord 1 x Quick User Guide

User Operation Guide
** For detail, updated Command Code and Application Software, please visit and download from www.abtussingapore.com
PRODUCT HIGHLIGHTS
•Multi-Stage surge protection
•Linear Filtering Technology
•Front panel power status LEDs
•External I/Os allow remote operation
** For detail, updated Command Code and Application Software, please visit and download from www.abtussingapore.com
Item Description
1. POWER Main Power ON/OFF switch
2. CIRCUIT BREAKER Max overall load capacity is 10 amp, this circuit breaker will trip should the combined
current drawn by all connected equipments exceed 10 amp.
Should this occurs, reduce the load so that they are within the range.
Reset can be done by simply pressing the reset button, however, please note that this is a
thermal trip supplementary protector. (*Cooling time is required before reset is allow)
3. SWTCHED AC OUTLET Provide a power outlet from front panel with main power ON/OFF and when the system
is in and under normal power condition.
4. PROTECTION OK LED is at solid green when system is under normal condition.
LED goes OFF when a extreme large surge occurs, all relays will open.
5. EXTREME VOLTAGE LED is normally off, it will only turn solid red when unit received voltage that is out of
the range below (185VAC) or above (265VAC)
*System will only allow reset (OFF/ON main power switch) when the incoming voltage
is back within the safety range.
6. SEQUENCE START Push to reset and begin an ON sequence
7. DELAY STATUS LEDs, each LED provide the relay/delay status of the corresponding port.
8. SEQUENCE ON/OFF ON/OFF of a sequence which allow outlets to be turn on one at a time with a delay time
(Variable and programmable) between each one.
9. LAMP ON/OFF ON/OFF control for rear 12VDC (500mA) supply which allow any gooseneck lamp/LED
to be connected.
Front Panel View
1 2 3 4 5 6 7 8 9
•8 switched outlets (rear) and one pass through
un-switched outlet (front)
•12VDC supply (BNC) allow any gooseneck lamp or LEDs
that provides a cool running source for the rack
1 2 3 4
Item Description
1. LAMP BNC 12VDC (500mA) gooseneck lamp/LED
2. LED - START SEQ- GND External control and status for Start Sequence
3. DELAY 1 to DELAY 8 AC outlet with delays and sequence based on programmed timing (1~60 Sec)
4. AC AC220~240 50/60Hz AC Input socket, AC220~240 50/60Hz
Communication Parameter
RS-232 Command Code
Description Setting
Baud Rate : 9600bps
Data Length : 8 bits
Parity : Non Parity
Stop Bit : One stop bit
X On/Off : None
RS-232 connection
Pin Function
1 Tx Transmit data
2 Rx Receive data
3 GND Ground Tx - Rx - GND
Item Description Command code (Hex)
1. Enter Setting Mode Send 53 45 54 53 07 50 57 52 44 41 30 39 43
Return 52 45 54 53 07 50 57 52 44 41 30 39 43
2. Set Relay 01 ON (Hex 01) Delay 01 sec Send 53 45 54 53 04 44 4C 01 01
Return 52 45 54 53 04 44 4C 01 01
3. Set Relay 02 ON (Hex 02) Delay 02 sec Send 53 45 54 53 04 44 4C 02 02
Return 52 45 54 53 04 44 4C 02 02
4. Set Relay 03 ON (Hex 03) Delay 03 sec Send 53 45 54 53 04 44 4C 03 03
Return 52 45 54 53 04 44 4C 03 03
5. Set Relay 04 ON (Hex 04) Delay 04 sec Send 53 45 54 53 04 44 4C 04 04
Return 52 45 54 53 04 44 4C 04 04
6. Set Relay 05 ON (Hex 05) Delay 05 sec Send 53 45 54 53 04 44 4C 05 05
Return 52 45 54 53 04 44 4C 05 05
7. Set Relay 06 ON (Hex 06) Delay 06 sec Send 53 45 54 53 04 44 4C 06 06
Return 52 45 54 53 04 44 4C 06 06
8. Set Relay 07 ON (Hex 07) Delay 07 sec Send 53 45 54 53 04 44 4C 07 07
Return 52 45 54 53 04 44 4C 07 07
9. Set Relay 08 ON (Hex 08) Delay 08 sec Send 53 45 54 53 04 44 4C 08 08
Return 52 45 54 53 04 44 4C 08 08
10. Set Relay 08 ON (Hex 08) Delay 10 sec (Hex 0A) Send 53 45 54 53 04 44 4C 08 0A
Return 52 45 54 53 04 44 4C 08 0A
11. Set Relay 08 OFF (Hex 10) Delay 01 sec Send 53 45 54 53 04 44 4C 10 01
Return 52 45 54 53 04 44 4C 10 01
12. Set Relay 07 OFF (Hex 0F) Delay 02 sec Send 53 45 54 53 04 44 4C 0F 02
Return 52 45 54 53 04 44 4C 0F 02
13. Set Relay 06 OFF (Hex 0E) Delay 03 sec Send 53 45 54 53 04 44 4C 0E 03
Return 52 45 54 53 04 44 4C 0E 03
14. Set Relay 05 OFF (Hex 0D) Delay 04 sec Send 53 45 54 53 04 44 4C 0D 04
Return 52 45 54 53 04 44 4C 0D 04
15. Set Relay 04 OFF (Hex 0C) Delay 05 sec Send 53 45 54 53 04 44 4C 0C 05
Return 52 45 54 53 04 44 4C 0C 05
16. Set Relay 03 OFF (Hex 0B) Delay 06 sec Send 53 45 54 53 04 44 4C 0B 06
Return 52 45 54 53 04 44 4C 0B 06
17. Set Relay 02 OFF (Hex 0A) Delay 07 sec Send 53 45 54 53 04 44 4C 0A 07
Return 52 45 54 53 04 44 4C 0A 07
18. Set Relay 01 OFF (Hex 09) Delay 08 sec Send 53 45 54 53 04 44 4C 09 08
Return 52 45 54 53 04 44 4C 09 08
19. Set Relay 01 OFF (Hex 09) Delay 10 sec (Hex 0A) Send 53 45 54 53 04 44 4C 09 0A
Return 52 45 54 53 04 44 4C 09 0A
20. Exit (Setting Mode) Send 53 45 54 53 06 49 53 50 4F 4B 21
Return 53 45 54 53 06 49 53 50 4F 4B 21
Back Panel View