Active Controls ErgoRejoy User manual

The ErgoReJoy assessment kits are shipped in a custom box with each component labeled with part
numbers to facilitate installation. We recommend storing the 5” and 8” adjustable arms; double
ball adaptor; and JoyPad™ with 3” extension arm in the sample case until required for use during
the assessment.
I. Install socket brackets (30380) (with pre-installed sockets 30200) to PWC armrest using
the Stealth universal round tube mounting brackets (refer to gure A). f the PWC’s
armrests do not have mounting slots for the brackets’ nuts, then it may be necessary to drill
and tap holes in the armrests’ pads brackets (refer to gure ). f the Stealth brackets are
not compatible with the PWC armrests, please call -00-- ext .
. nsert mini mast (0) in socket (000) (refer to gure a). Press down on the top of
the mini-mast to make sure it is fully inserted (refer to gure b).
. nstall PWC joystick to ErgoReJoy platform (00). efore removing joystick from PWC,
photograph a side view in its standard armrest position.
A. Remove joystick harness from controller joystick port located on the PWC base noting
its location
. Remove joystick and joystick mounting bracket from PWC.
C. Ret joysticks have two different joystick cable congurations
. f the Ret joystick has a removable harness, install the Active Controls joystick
harness (0) in place of the original harness
a. Route the 0 cable through the long slot of the ErgoReJoy platform (00)
. f the Ret joystick has a xed harness, route the harness through the long slot of the
joystick platform (00)
D. nstall Ret joysticks with xed harnesses and
R joysticks with  M- screws in the front two
holes which are -” apart (see gure ) to
platform (00)
E. nstall Ret joysticks with removable harness in
the two rear holes which are  ” apart
(see gure )
F. nstall -ogic ,  or , E, Shark joysticks
with two M- screws using the  holes which are
-” apart (refer to gure )
Modular ERGOnomic REpositioning
JOYstick Platform Installation Instructions
figure 1a
figure 1B
figure 2a
figure 2B

G. nstall i joystick by installing the i mounting bracket to the top of the ErgoReJoy platform using the two
holes shown in gure . Mount i joystick to i mounting plate. Position housing of joystick at least ”
from the two ” balls on top of the ErgoReJoy joystick platform and use the  M screws to install the joystick
. nstall Shark joystick by adding black spacer block under joystick and installing both with two long M- screws
through holes  ” apart (refer to gure ).
. Coil the joystick cable tightly and secure it under the platform using the cable holders
attached. eave approximately ” of cable to connect to the joystick connection harness in
the next step (refer to gure ).
. nstall joystick specic harnesses to joystick and connect to mini-mast harness (0).
se the cable holders under the platform if needed to secure excess cable length. The
mini-mast connection harnesses for each joystick are as follows
A. Ret xed cable joysticks connect to RET ” Extension harness. Connect ” ext. to
00 mast connection harness. Connect 00 to 0 mini-mast harness
. Ret removable harness - replace with 0 and connect it to 0 mini
mast harness
C. -ogic   , E (no mast harness required)
D. -ogic  (0)
E. R (00)
F. i ()
G. Shark (00)
. nstall Active Controls extension harness (0) to each socket(s) harness (0).
A. Assessment kits include two or more sockets and require attaching each extension harness (0) to the
multiple socket harness (00).
. For single socket installations, install (0) to socket harness (0)
. Attach joystick connection harness and extension harness into the controller’s joystick port.
A. Connect Active Controls joystick specic controller harness to the 00 (for two or more socket conguration)
or 0 extension harness (for single socket conguration). The specic controller connection harnesses are as
follows
. Ret (00)
. -ogic   , E
. -ogic  (0)
. R (00)
. i ()
. Shark (00)
. Connect the joystick’s controller connection harness into the controller port where the
joystick was originally connected.
. Position joystick and ErgoReJoy platform at the end of armrest in the standard joystick
location (refer to photo taken in Step III above).
A. Conrm the receiver sockets are located at the lowest socket height and secured in place
by the adjustable handle (see gure )
figure 5
figure 4

. Attach ” extension arm (0) to .” ball attached in the middle of the bottom of
ErgoReJoy platform (00) and mini mast ball (mini mast 0)
C. Position joystick in standard PWC armrest location (see photo taken of joystick attached
to armrest for reference). Conrm that the joystick cable is tight against the bottom of the
platform and the ” extension arm is also as level as possible (refer to gure ).
D. f the socket is in the lowest position in the slot, then additional lower adjustments can
be made by lowering the round tube portion of the Stealth universal round tube mounting
bracket in its slots.
E. Tighten knob of ” extension arm snugly.
. Sit on PWC and turn joystick on to conrm connections are correct. Test ride to conrm joystick and platform
are secure.
. f assembling a two socket system, remove joystick and ErgoReJoy assembly out of the receiver socket and insert
in the opposite armrest’s socket. Conrm mini-mast is fully inserted.
A. Repeat the test ride
. Additional ErgoReJoy joystick locations can be sampled if desired. n order to drive
the PWC in any of the locations other than the armrest, raise the socket to its’ highest
position in the socket bracket’s slot (see gure ). See the joystick positioning protocol
for which extension arms to use in each location.
. Return the ErgoReJoy platform to the standard armrest conguration with ” extension
arm in position with the sockets in lowest position (refer to gure ).
XIII. Remove ErgoReJoy joystick assembly without loosening its adjustment knob from its receiver socket and store in
assessment case in the center location. Return ” and ” extension arms, double ball adaptor and the JoyPad,
with small ” extension arm to the assessment case.
XIV. Place the PWC on charge for initial assessment.
figure 6
figure 7