ADJ ACCU-STAND PRO EVENT TBL 2 User manual

PRO EVENT TBL 2
User Guide

2
©2023 ADJ Products, LLC all rights reserved. Information, specications, diagrams, images, and instructions herein
are subject to change without notice. ADJ Products, LLC logo and identifying product names and numbers herein are
trademarks of ADJ Products, LLC. Copyright protection claimed includes all forms and matters of copyrightable materials
and information now allowed by statutory or judicial law or hereinafter granted. Product names used in this document may
be trademarks or registered trademarks of their respective companies and are hereby acknowledged. All non-ADJ Products,
LLC brands and product names are trademarks or registered trademarks of their respective companies.
ADJ Products, LLC and all afliated companies hereby disclaim any and all liabilities for property, equipment, building, and
electrical damages, injuries to any persons, and direct or indirect economic loss associated with the use or reliance of any
information contained within this document, and/or as a result of the improper, unsafe, insufcient and negligent assembly,
installation, rigging, and operation of this product.
ADJ PRODUCTS LLC World Headquarters
6122 S. Eastern Ave. | Los Angeles, CA 90040 USA
Tel: [phone] | Fax: [phone] | www.adj.com |[email protected]
ADJ Supply Europe B.V.
Junostraat 2 | 6468 EW Kerkrade | Netherlands
Tel: [phone] | Fax: [phone] | www.americandj.eu | [email protected]
DOCUMENT VERSION
Due to additional product features and/or enhancements, an updated version of this document may
be available online.
Please check www.adj.com for the latest revision/update of this manual before beginning
installation and/or programming.
Date Document Version Notes
07/24/2023 1.0 Initial Release

3
General Information 4
Limited Warranty 6
Setup Instructions 7
Specifications | Dimensions | Optional Accessories 11
CONTENTS

4
GENERAL INFORMATION
INTRODUCTION
Please read and understand the instructions in this manual carefully and thoroughly before attempting
to operate this device. These instructions contain important safety and use information.
This product is intended for use by professionally trained personnel only, and is not suitable for
private use.
UNPACKING
Every device has been thoroughly tested and has been shipped in perfect operating condition. Carefully
check the shipping carton for damage that may have occurred during shipping. If the carton is damaged,
carefully inspect the device for damage, and be sure all accessories necessary to install and operate
the device have arrived intact. In the event damage has been found or parts are missing, please contact
our customer support team for further instructions. Please do not return this device to your dealer
without rst contacting customer support. Please do not discard the shipping carton in the trash. Please
recycle whenever possible.
INCLUDED ITEMS:
• (2) Metal Table Half Sections (Left and Right)
• (2) Black Painted Metal Support Bars
• (4) Thumb Screws
• (1) Carpeted Shelf
• (1) Front Poster Board
• (4) Front Poster Board Screws

5
CUSTOMER SUPPORT
ADJ® provides a customer support line, to provide set up help and to answer any question should
you encounter problems during your set up or initial operation. You may also visit us on the web at
www.adj.com for any comments or suggestions. For service related issue please contact ADJ.
ADJ SERVICE USA - Monday - Friday 8:00am to 4:30pm PST
Voice: 800-322-6337 Fax: [phone]
E-mail: [email protected]
ADJ GROUP SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET
Voice: [phone] Fax: [phone]
E-mail: [email protected]
WARRANTY REGISTRATION
The PRO EVENT TBL 2 is covered by a 1 year (365 days) limited warranty. All returned service
items whether under warranty or not, must be freight pre-paid and accompany a return authorization
(R.A.) number. The R.A. number must be clearly written on the outside of the return package. A brief
description of the problem as well as the R.A. number must also be written down on a piece of paper
and included in the shipping container. If the unit is under warranty, you must provide a copy of your
proof of purchase invoice. Items returned without a R.A. number clearly marked on the outside of
the package will be refused and returned at customer’s expense. You may obtain a R.A. number by
contacting customer support.

6
LIMITED WARRANTY (USA ONLY)
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products to be free of manufacturing
defects in material and workmanship for a prescribed period from the date of purchase (see specic warranty period
on reverse). This warranty shall be valid only if the product is purchased within the United States of America, including
possessions and territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B. For warranty service, you must obtain a Return Authorization number (RA#) before sending back the product-please
contact ADJ Products, LLC Service Department at 800-322-6337. Send the product only to the ADJ Products, LLC
factory. All shipping charges must be pre-paid. If the requested repairs or service (including parts replacement) are
within the terms of this warranty, ADJ Products, LLC will pay return shipping charges only to a designated point within
the United States. If the entire instrument is sent, it must be shipped in its original package. No accessories should be
shipped with the product. If any accessories are shipped with the product, ADJ Products, LLC shall have no liability
whatsoever for loss of or damage to any such accessories, or for the safe return thereof.
C. This warranty is void of the serial number has been altered or removed; if the product is modied in any manner which
ADJ Products, LLC concludes, after inspection, affects the reliability of the product, if the product has been repaired or
service by anyone other than ADJ Products, LLC factory unless prior written authorization was issued to purchaser by
ADJ Products, LLC; if the product is damaged because not properly maintained as set forth in the instruction manual.
D. This is not a service contact, and this warranty does not include maintenance, cleaning or periodic check up. During
the period specied above, ADJ Products, LLC will replace defective parts at its expense with new or refurbished parts,
and will absorb all expenses for warrant service and repair labor by reason of defects in material or workmanship. The
sole responsibility of ADJ Products, LLC under this warranty shall be limited to the repair of the product, or replacement
thereof, including parts, at the sole discretion of ADJ Products, LLC. All products covered by this warranty were
manufactured after August 15, 2012, and bear identifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products without any
obligation to include these changes in any products theretofore manufactured.
F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products
described above. Except to the extent prohibited by applicable law, all implied warranties made by ADJ Products, LLC
in connection with this product, including warranties of merchantability or tness, are limited in duration to the warranty
period set forth above. And no warranties, whether expressed or implied, including warranties of merchantability or
tness, shall apply to this product after said period has expired. The consumer’s and/or Dealer’s sole remedy shall be
such repair or replacement as is expressly provided above; and under no circumstances shall ADJ Products, LLC be
liable for any loss or damage, direct or consequential, arising out of the use of, or inability to use, this product.
G. This warranty is the only written warranty applicable to ADJ Products, LLC Products and supersedes all prior warranties
and written descriptions of warranty terms and conditions heretofore published.
LIMITED WARRANTY PERIODS
• Non L.E.D. Lighting Products = 1-year (365 days) Limited Warranty (Such as: Special Effect Lighting, Intelligent
Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands etc.
excluding LED and lamps)
• Laser Products = 1 Year (365 Days) Limited Warranty (excludes laser diodes which have 6 month limited warranty)
• L.E.D. Products = 2-year (730 days) Limited Warranty (excluding batteries which have a 180 day limited warranty)
Note: 2 Year Warranty only applies to purchases within the United States.
• StarTec Series = 1 Year Limited Warranty (excluding batteries which have a 180 day limited warranty)
• ADJ DMX Controllers = 2 Year (730 Days) Limited Warranty

7
SETUP INSTRUCTIONS
1. Unfold both table sections and position them close towards each other.
2. Intersect both table sections together, inserting one side into the other side..

8
3. Make sure both table sections fit together properly and there are no gaps/spaces between them..
4. Secure both table sections together by installing (2) black metal table support bars.
Insert square ends of each support bar into the slots on each side of the table.
Insert the front bar first then insert the back bar. Make sure each support bar is completely
inserted into the slots and make sure both table sections are level and sitting on a flat surface.

9
5. Hand tighten the (4) thumb screws located on the support bar slots on both ends of the table.
6. Place the carpeted shelf inside the top section of the table on top of both metal support bars, with
the open cable hole facing front. Make sure the shelf is completely installed and flat before placing
any equipment on it.

10
6. Attach logo or poster board to the front side of the table using the included (4) screws. Make sure
not to overtighten the screws to avoid damaging poster board.

11
23.6"
(600mm)
47.6" (1210mm)
45.3" (1150mm)
DIMENSIONS
Drawing not to scale
ORDER CODE ITEM
PRO111 PRO EVENT TBL 2
PRO222 PRO EVENT TBL 2 MB
PRO333 PRO EVENT IBEAM ST
PRO800 PRO EVENT TABLE 2 BAG
PRO880 PRO EVENT TABLE CORNER SHELF - PAIR
PRO999 PRO EVENT TABLE SCRIM BLK
PRO399 PRO EVENT TABLE SCRIM WH
OPTIONAL ACCESSORIES
SPECIFICATIONS
• Professional aluminum event table to use as a greeting table, sales table, live sound or lighting
designer console or DJs
• Compact and collapsible - collapses in half for compact transport
• Lightweight, around 40 lbs.
• Functional and professional looking
• Shelf height: 34 inches
• Front board to add custom graphic (Size (WxH); 25” x 22.5” / 635x571.5mm)
• Dimensions (LxWxH): 50” x 24” x 45.5” / 1270x610x1155mm