Adstec Hdbtbox-rx User manual

Updated 2022-08-23

Instruction manual

HDBaseT™Box

HDBTBOX-RX / HDBTBOX-TX

Translation of the original

instruction manual Version 1.1

HDBTBOX-RX / HDBTBOX-TX −Instruction manual v1.1 2

Read these instructions carefully before using and store for future reference.

These instructions contain important information about the product, in particular about its

intended use, safety, installation, utilisation, maintenance and disposal.

Hand over the instructions to the user following installation of the product, and pass the manual

on to the new user if the product is resold.

These instructions can be downloaded from: www.ads-tec.com in the download area.

Publisher

ads-tec Industrial IT GmbH

Heinrich-Hertz-Straße 1

72622 Nürtingen

Phone: +49 7022 2522-0

Internet: www.ads-tec.com

E-mail: mailbox@ads-tec.de

HDBTBOX-RX / HDBTBOX-TX −Instruction manual v1.1 3

Contents

1General information about documentation...............................................................................4

1.1 General information 4

1.2 Explanation of safety instructions 4

1.2.1 Structure of safety instructions 4

1.2.2 Explanation of signal words 5

1.3 Relevant device documentation 6

1.4 Symbols 6

1.5 Data, figures and modifications 6

1.6 Trademarks 7

1.7 Copyright 7

2General device information ......................................................................................................8

2.1 Manufacturer and contact details 8

2.2 Intended use 8

2.3 Improper use 9

2.4 Environmental conditions 10

2.5 Conformity 11

2.6 Warranty / repairs 12

2.7 Limitation of liability 12

3Scope of delivery....................................................................................................................13

4Mechanical installation ..........................................................................................................14

4.1 External device dimensions 14

4.2 Top-hat rail mounting 15

5Electrical connections.............................................................................................................16

5.1 Requirements 16

5.2 Interfaces 17

5.2.1 Overview 17

5.2.2 Power supply 18

5.2.3 HDBaseT™ connection: maximum cable lengths 18

6Status LEDs ............................................................................................................................19

7Cleaning.................................................................................................................................19

8Technical data........................................................................................................................20

9Service & support...................................................................................................................21

9.1 ADS-TEC support 21

9.2 Company address 21

HDBTBOX-RX / HDBTBOX-TX −Instruction manual v1.1 4

1 General information about documentation

1.1 General information

This instruction manual is intended to ensure safe and efficient handling of the HDBaseT™ Box kit

consisting of a transmitter and a receiver (HDBTBOX-RX / HDBTBOX-TX). These are referred to in the

following as "devices".

All of the safety instructions and handling instructions given in the manual must be obeyed in order to

ensure that work is carried out safely.

All users must read this instruction manual and have access to it at all times.

The original version of this instruction manual was written in German. All non-German versions of this

instruction manual are translations of the German instruction manual.

1.2 Explanation of safety instructions

1.2.1 Structure of safety instructions

The signal word classifies the hazard.

Reference to the type/consequences and source of the hazard is made underneath the signal word.

Information on how to avoid the hazard is indicated by an arrow ().

DANGER

Type and source of the hazard!

Possible consequences if the hazard is disregarded

Measures for avoiding the hazard

HDBTBOX-RX / HDBTBOX-TX −Instruction manual v1.1 5

1.2.2 Explanation of signal words

DANGER

Indicates an imminent danger. If not avoided, death or severe injury will

result.

WARNING

Indicates a possible danger. If not avoided, death or severe injury could

result.

CAUTION

Indicates a possible danger. If not avoided, light or minor injuries could

result.

ATTENTION

Indicates a possibly damaging situation. If not avoided, the system or something in its

surroundings could be damaged.

Recommendation for use:

Indicates terms and/or conditions that strictly need to be observed to ensure

optimised and/or zero-defect operation. Tips and suggestions for the efficient use

of the device and software optimisation are also provided.

HDBTBOX-RX / HDBTBOX-TX −Instruction manual v1.1 6

1.3 Relevant device documentation

The following documents are decisive to device setup and operation:

•This instruction manual:

contains information for installation, commissioning and operation of the device along with

technical data.

•Website:

You can download the instruction manual as well as drivers, software, user manuals, leaflets

and flyers from the Download area of our website www.ads-tec.com

1.4 Symbols

Symbol Meaning

Label on batteries. The batteries may not be disposed of with household waste, but must

rather be disposed of separately. Used batteries must be returned to the point of sale or a

disposal system.

Label on electrical and electronic devices. Electrical and electronic devices must not be

disposed of with household waste, but must rather be taken to a collection point for waste

electrical equipment.

1.5 Data, figures and modifications

All data, text and figures were prepared to the best of our knowledge. They do not represent any

assurance for the properties themselves. Despite taking utmost care, no liability can be assumed for

accuracy, completeness and actuality of the information. Subject to changes.

HDBTBOX-RX / HDBTBOX-TX −Instruction manual v1.1 7

1.6 Trademarks

It is noted that any software and/or hardware trademarks and any company brand names mentioned in

this documentation are all subject to the general trademark protection rights.

Big-LinX®and X-Remote®are registered trademarks of ADS-TEC.

All other third-party trademarks used are hereby acknowledged.

In the case of infringement of trademark rights, ADS-TEC reserves the right to exercise all rights.

1.7 Copyright

This instruction manual is protected by copyright. For the authorised user, simple usage rights are

granted within the scope of the intent of the contract. Any modified use or exploitation of the provided

content, particularly duplication, modification or publishing in whatever form is permitted only with the

prior consent of ADS-TEC. In the case of copyright infringement, ADS-TEC reserves the right to

exercise all rights.

HDBTBOX-RX / HDBTBOX-TX −Instruction manual v1.1 8

2 General device information

2.1 Manufacturer and contact details

The manufacturer of the device is ads-tec Industrial IT GmbH. The company is referred to in the

following as ADS-TEC.

ads-tec Industrial IT GmbH

Heinrich-Hertz-Str.1

72622 Nürtingen

Germany

Phone: +49 7022 2522-0

Email: mailbox@ads-tec.de

Web: www.ads-tec.com

2.2 Intended use

The HDBaseT™ Box kit allows data transmission between a computer and a display over distances of

up to 100 m.

The device is intended for industrial use and in this case primarily for use in machine and plant

construction. In accordance with its IP protection class, it may be installed in cabinets or mounted on

machines/plants indoors. Install the product in a service area away from general public access.

The operator alone shall be responsible for ensuring that all operator obligations are observed and for

complying with any technical or statutory amendments that may arise.

Installation, commissioning and operation may only be performed by qualified and trained personnel.

Intervention by the user is required only for performing the actions described in this document. Should

any further modifications be required, it is necessary to consult either with the manufacturer directly or

with service personnel authorised by the manufacturer.

The device must be de-energised during service work. Appropriate measures must be taken to prevent

electrostatic discharges on components.

The device is only to be assembled, installed and operated within the permissible specifications.

Use in non-specified environments is prohibited.

HDBTBOX-RX / HDBTBOX-TX −Instruction manual v1.1 9

2.3 Improper use

Operation other than or beyond that described for the device shall be deemed improper use.

If the device is used in a manner not specified by the manufacturer, the protection provided by the

device may be impaired.

The device is not allowed to be used to control vehicles or for applications for which further approvals

beyond the manufacturer's declaration are necessary, e.g. applications with explosion hazard, medical

technology and shipping industry.

The product does not support any safety functions of functional safety. Do not use the product to

evaluate safety-relevant data in order to bring a system to a safe state.

The device must not be put into operation in the case of transport damage or nonconformity with the

specifications and must be taken out of operation in the case of changing conditions.

In the case of improper use, ADS-TEC shall not accept responsibility or liability for injury or damage that

is directly or indirectly attributable to the handling of the device.

If the device is opened up by an unauthorised person, the user may be subject to hazards and the

warranty is invalidated.

Should the device have evident signs of damages caused, e.g., by improper operation or storage

conditions or due to improper use or handling, it must be shut down immediately. Ensure that it is

secured against being started up accidentally.

The device can be damaged as a result of unauthorised mechanical modifications. Make sure that the

device is not drilled, chiselled or perforated and its exterior shape and design is not modified in any way!

HDBTBOX-RX / HDBTBOX-TX −Instruction manual v1.1 10

2.4 Environmental conditions

The device must be operated under the environmental conditions specified in the technical data.

Failure to observe any one of these conditions will invalidate the warranty of the device. ADS-TEC

cannot be held liable for any damages arising from improper use and handling.

ATTENTION

Damage caused by heat!

If the device is installed in a panel, casing or similar, heat accumulation can occur.

Make sure that heat can be dissipated from the device.

ATTENTION

Damage caused by condensation!

If the temperature of the device is different to that of the environment in which it is located,

condensation can form.

Switch on the device only after it has acclimated to the ambient temperature.

ATTENTION

Damage caused by heat!

If the device is exposed to sunlight or any other light or heat source, it can overheat and suffer

damage.

Do not expose the device to direct radiation by sunlight or any other light or heat source!

HDBTBOX-RX / HDBTBOX-TX −Instruction manual v1.1 11

2.5 Conformity

The manufacturer hereby declares that the product described in this instruction manual complies with all

relevant stipulations of the following European directives:

•2011/65/EU RoHS Directive

•2014/30/EU EMC Directive

•2014/35/EU Low Voltage Directive

The device is a class A device (Industry). Class A may cause interference when used in residential

environments.

The EU conformity declaration is available for download at

https://www.ads-tec-iit.com/en/support/industrial-it/ec-declaration.html

Recommendation for use:

For full compliance with the EMC legislation, all components and cables used for

device connection must also be compliant with these requirements. It is therefore

necessary to employ BUS and LAN cables with shielded connectors and these

must be installed as per the instructions contained in the respective instruction

manuals.

HDBTBOX-RX / HDBTBOX-TX −Instruction manual v1.1 12

2.6 Warranty / repairs

During the device warranty period, any repairs must only be performed by the manufacturer or by

service personnel that has been authorised by the manufacturer.

2.7 Limitation of liability

ADS-TEC shall not be liable for personal injury, property damage or damage caused to the device as

well as consequential damage that is/was the result of non-compliance with this instruction manual,

improper use of the device, repairs and other actions on the device by unqualified electricians and

electricians not certified by ADS-TEC, or that is/was the result of using unapproved replacement parts.

Failure to observe the maintenance intervals shall also result in exclusion from liability. Furthermore, it is

strictly forbidden to make any unauthorised alterations or technical modifications to the device.

HDBTBOX-RX / HDBTBOX-TX −Instruction manual v1.1 13

3 Scope of delivery

Check that the contents of the package are intact: If there are signs of damage, please contact the

manufacturer immediately. The device must not be put into operation.

Check that the contents of the package are complete and match your order:

−Device

−3-pin connector for power supply

−Optional accessories according to order/delivery note, e.g. a power supply unit

HDBTBOX-RX / HDBTBOX-TX −Instruction manual v1.1 14

4 Mechanical installation

4.1 External device dimensions

RX and TX have the same outer dimensions:

HDBTBOX-RX / HDBTBOX-TX −Instruction manual v1.1 15

4.2 Top-hat rail mounting

The devices are intended for mounting on a top-hat rail (TS35) in vertical orientation as shown in the

picture below.

1. Position the IRF on the top-hat rail from below at an angle (1).

2. Pull the top-hat rail locking mechanism (2) upwards using a screwdriver, push the device from above

onto the top-hat rail and remove the screwdriver.

3. The top-hat rail locking mechanism springs back to its original position.

4. Check that the IRF is seated securely on the top-hat rail.

To release the device from the top-hat rail, proceed in the reverse order.

HDBTBOX-RX / HDBTBOX-TX −Instruction manual v1.1 16

5 Electrical connections

5.1 Requirements

ATTENTION

Damage due to electrostatic discharge!

Damage to the device can be caused by electrostatic discharge.

•Always adhere to the safety measures applicable when handling components at risk of being

damaged by electrostatic discharge.

ATTENTION

Damage to the electronics!

The electronics can be damaged if connectors are connected or disconnected while power is still

being applied.

•Make sure that no power is being applied when connecting and disconnecting connectors.

HDBTBOX-RX / HDBTBOX-TX −Instruction manual v1.1 17

5.2 Interfaces

5.2.1 Overview

Apart from the direction of transmission, Transmitter (Tx) and Receiver (Rx) have got the same

interfaces:

No. Description

1 Power LED: indicates whether the device is on or not

2 Power supply →see sec. 5.2.2

3 Firmware LED

4 HDBaseT™ connection: RJ45, 100 Mbit/s

with LEDs for HDBaseT and HDCP →see sec. 6

5 HDMI connection: transmission of the videos

6 USB 2.0 connection: transmission of the signals of the touch screen

−Rx: type A

−Tx: type B

HDBTBOX-RX / HDBTBOX-TX −Instruction manual v1.1 18

5.2.2 Power supply

The electronics are galvanically isolated from the power supply via a DC-DC converter.

0V Reference potential

NC Not connected

V+ +12… 24 VDC ± 20 %

Conductor cross sections: AWG 18 (≙0.75 mm2)

Recommendation

Use flexible cables and appropriate cable end sleeves.

To minimise mechanical strain between the individual

wires and the plug, the distance between jacket and plug

should be at least 30 mm.

Requirements on the power supply

•Conformity:

- Class PS2 acc. to IEC 62368-1 or

- Limited Power Source (LPS) acc. to IEC 60950-1

- For devices with UL-Certification: NEC Class 2

Informations on using the device acc. to UL certification (Underwriter Laboratories, USA):

•The external circuits intended to be connected to this device shall be separated from the mains

supply or hazardous live voltage by reinforced or double insulation and meet the requirements

of SELV/PELV-Limited Energy (IEC 61010-1, clause 9.4) or Class PS2 acc. to IEC 62368-1 or

LPS acc. to IEC 60950 or Class 2 acc. to NEC.

•In order to connect the power supply: Only use copper conductors with UL certified wire

ferrules.

5.2.3 HDBaseT™ connection: maximum cable lengths

Recommendation

−CAT6a for distances of up to 80 m with at least 24 AWG

−CAT7 for distances of up to 100 m with at least 24 AWG

HDBTBOX-RX / HDBTBOX-TX −Instruction manual v1.1 19

6 Status LEDs

1POWER

Device is ON/OFF.

2Firmware

No Firmware action

Firmware is up and running

3HDBT

HDBaseT link active

No link

4HDCP*) Transmission of content without HDCP

protection

Transmission of content with HDCP

protection (in case of copyright protected

contents)

*) HDCP = High-bandwidth Digital Content Protection. HDCP versions 1.x and 2.2 are supported.

Legend:

OFF

Flashing

7 Cleaning

Clean the device using some glass cleaner on a soft cloth.

HDBTBOX-RX / HDBTBOX-TX −Instruction manual v1.1 20

8 Technical data

Housing Fanless die-casting aluminium housing

Interfaces HDBaseT™ : RJ45 (100 Mbit/s)

HDMI

USB 2.0 (Rx: type A / Tx: type B): max. 0.5 A

Power supply Voltage: 12…24 VDC ± 20%

Power: RX: max. 10 W / TX: max. 4.5 W

For more detailed information: see chapter 5.2.2.

Data of the optional power supply unit (DZ-PCKO-06166-0/A):

−Input: 100…240 VAC, 50…60 Hz, max. 0.32 A, inrush current: max. 120 A

−Output: 24 VDC ± 5 %, max. 0.5 A, max. 12 W

−Dimensions: 80 x 46 x 41 mm ± 1 mm

−Temperatures: Operating 0…+60 °C, Storage -20…+80 °C

−Humidity: Operating 20…80 %, Storage 10…90 %, non condensing

−MTBF: 300,000 h @25 °C

Permiss. ambient

temperatures

Operation -26…+60 °C

Storage -30…+80 °C

Protection Ingress Protection code IP 30

Humidity 10…85 %, non-condensing

Pollution degree 1 as per IEC 61010-1

Altitude during

operation

2000 m or less

Vibration/shock

resistance

DIN EN 60068-2-6

DIN EN 60068-2-27

EMC Class A (industrial sector) as per EN 61000-6-2/4

Dimensions 158 x 35 x 123mm →see section 4.1

Weight Approx. 500 g

This manual suits for next models

Table of contents

Popular Receiver manuals by other brands

Pioneer

Pioneer AVH-X8890BT owner's manual

AV Access

AV Access 4KEX70-RX user manual

Sony

Sony STR-V323 operating instructions

CaryMart

CaryMart 0020040 manual

Yamaha

Yamaha Aventage RX-A1020 owner's manual

SMART

SMART MX52 user manual

Linear

Linear DXR-702 installation instructions

Audioplex

Audioplex KS-2 EYE installation manual

Pioneer

Pioneer MVH-S100UI owner's manual

Tivoli Audio

Tivoli Audio BiuCon owner's manual

Manhattan

Manhattan Plaza HDR S 500GB user guide

Sola

Sola REC LGD0 operating instructions

Dakota Alert

Dakota Alert RE-4k Plus user guide

Hyundai

Hyundai H-1604 instruction manual

Ferguson

Ferguson ARIVA 100 user manual

JVC

JVC RX-5040B instructions

McLED

McLED ML-910.048.22.0 installation manual

DELTA DORE

DELTA DORE RF 6620 instructions

adstec HDBTBOX-RX User manual

Popular Receiver manuals by other brands