Advance Tabco K-175 Guide

Installation & Operation Instructions for
ELECTRONIC FAUCETS
CHECK FOR CONCEALED DAMAGE
FILE CLAIM WITH FREIGHT CARRIER
ADVANCE TABCO Electronic Faucets are recommended for practical applications.
ADVANCE TABCO does not recommend product use for activities employing harsh and active
chemicals. Please consult factory regarding unusual applications.
200 Heartland Boulevard, Edgewood, NY 11717-8380
©ADVANCE TABCO, JANUARY 2006
Questions and Answers
Q. Can I operate the faucet manually,without using the Electronic Eye?
A. Yes. Press the on/off button and water will start flowing. To turn water
off,press on/off button again. if you forget to turn the water off,the
faucet will automatically turn it off after 60 seconds.
Q. What is the optimal Sensing Distance?
A. About 2” from the Sensor is recommended.
Q. Does the Electronic Eye require special maintenance?
A. Yes. In order for the Sensor to function properly, the Electronic Eye
must be kept clean. Use only mild soaps and water. wipe with a soft
cloth.
Q. How often should I clean the filter?
A. Depending on the quality of the water in your area, every 4-12 weeks.
Q. Why doesn’t the water shut itself off after I have moved my hands
away from the Electronic Eye?
A. The Sensor Range could be too long. User may have to adjust
sensor Range (See page 2 on how to set the Sensor Range).
Q. No water will come out of the faucet and the Red LED Light stays on.
A. Replace the batteries (See page 2 for battery installation).
K-175
Splash Mounted
K-180
Deck Mounted
Operation
1. Place hands under spout. Water will flow for as long as the user’s
hands remain within sensor range.
2. Clean filter every month.
3. Keep Electronic Eye Cover clean.
4. Red flashing in the Electronic Eye indicates low batteries.
5. Solid red light in the Electronic Eye and no water flow
indicates batteries are dead.
6. When used in conjunction with the optional AC adapter, the faucet will
automatically switch to AC Power and conserve its battery power.
NOTE: Faucet will automatically shut off at approximately 45 seconds
if the Electronic Eye detects an object or non movement to
prevent continuous water flow.

1. Main Body
2. Spout
3. Infrared Sensor Eye
4. Splash Nut
5. Connect Line Cable
6. Filter
7. Control Box
8. Battery Cover
9. On/Off Control Button
10. Adapter: 100-240 VAC (Included)
11. Mechanical Mixing Valve
with Check Valves
12. Flexible Inlet Supply Lines
13. Flexible Supply Hose To Faucet
14. Elbow
Parts List Sensor Range Setup
1. Plug in the AC Power Adapter OR install Four (4) AA Alkaline
Batteries (See below for battery installation).
2. Sensor Range can only be set by using the on/off button situated
on the bottom right corner of the control box.
Do not attempt to open Control Box.
3. Push and hold the on/off button for 5-7 seconds (Figure 1).
Water will flow and then it will stop. Release button.
4. Place hand in front of the Electronic Eye and leave there until the
Red LED Light inside the Electronic Eye starts blinking.
5. Slowly, move your hand away from the sensor and stop at the
desired location you wish to have the faucet activate. Hold your
hand position until the LED Light blinks, signaling that the sensor
range is detected (figure 2).
With your other hand, Press the on/off button again to save the
new settings (Figure 1).The LED Light will stay on momentarily
indicating faucet is set.
Battery Installation
1. Your Sensor Faucet Requires Four (4) AA Alkaline Batteries. If the
AC Adapter is plugged in, unplug it from its power source.
2. Using a Philips Screw Driver, remove the cover’s
three (3) screws and pull cover away from the
Control Box using pliers (Figure 3).
3. Remove old batteries if applicable.
4. Install the new AA Alkaline batteries, making
sure the “+” and “-” symbols are facing in the
correct directions. Place the cover back on the
Control Box and tighten screws.
Fresh Alkaline Batteries should last
approximately 400,000 on/off cycles.
Maximum Running Time: 60 Seconds
Response Time: 0.3 Seconds
Sensing Range: 1-7 Inches From Sensor
Power Source: AC and/or DC
Low Battery Indicator: Red LED On
Figure 1 Figure 2
Figure 3
1
2
3
6
7
8
9
10
12
13
14
5
4
11
Install as Shown
with Tab
Facing Down