AEG Powertools SBE 630 R User manual
SBE 630 R
Original Instructions
2
2
33
III
VIII
IX
VIV
$FFHVVRU\
=XEHK|U
$FFHVVRLUHV
$FFHVVRULR
$FFHVVRULR $FHVVyULR
7RHEHKRUHQ 7LOEHK¡U
7LOEHK¡U 7LOOEHK|U
/LVlODLWH ǼȟĮȡIJȒȝĮIJĮ
$NVHVXDU 3Ĝ¿VOXãHQVWY¿
3UtVOXãHQVWY :\SRVDĪHQLH
$]RNDWDWDUWR]pNRNDW
2SUHPD 3LHGHUXPL
3ULHGDV 7DUYLNXG
ÀÁÀ½¿ºÄ·½Î
Ⱥɤɫɟɫɨɚɪɢ
$FFHVRULX ɨɩɨɥɧɢɬɟɥɧɚ
ɨɩɪɟɦɚ 愴ờ
5*1
III
VI
VII
4
4
I
55
I
6
6
II
77
III
8
8
[
IV
[
99
START
STOP
V
6WDUW
6WDUW6WRS
6WRS
MPDL
VOMPDL
6W
6W
6W
6W
6
6
DU
DU
DU
DU
W
W
W
W
6WDUW
10
10
IV
VI
11 11
VII
12
12
5*1
5*1
VIII
13 13
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and
may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for dierent applications, with
dierent accessories or poorly maintained, the vibration emission may dier. This may signicantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched o or when it is running
but not actually doing the job.This may signicantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eects of vibration such as: maintain the tool and the accessories, keep
the hands warm, organisation of work patterns.
WARNING! Read all safety warnings and all
instructions, including those given in the accompanying
brochure. Failure to follow the warnings and instructions may result
in electric shock, re and/or serious injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS
Wear ear protectors. Exposure to noise can cause hearing loss.
Use auxiliary handles supplied with the tool. Loss of control can
cause personal injury.
Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory may
contact hidden wiring or its own cord. Cutting accessory
contacting a„live“ wire may make exposed metal parts of the power
tool„live“ and could give the operator an electric shock.
Appliances used at many dierent locations including open air should
be connected via a residual current device (FI, RCD, PRCD) of 30mA
or less .
Always wear goggles when using the machine. It is recommended to
wear gloves, sturdy non slipping shoes and apron.
Sawdust and splinters must not be removed while the machine is
running.
Always disconnect the plug from the socket before carrying out any
work on the machine.
Only plug-in when machine is switched o.
Keep mains lead clear from working range of the machine. Always
lead the cable away behind you.
Do not use diamond core drills on hammer mode.
When working in walls ceiling, or oor, take care to avoid electric
cables and gas or waterpipes.
TECHNICAL DATA Percussion drill
SBE 630 R
Rated input..................................................................................................................................................................................... 630 W
Output ............................................................................................................................................................................................ 320 W
No-load speed ........................................................................................................................................................................... 0-2800 min
-1
Speed under load max. ............................................................................................................................................................. 0 - 1750 min -1
Rate of percussion under load max. ............................................................................................................................................ 44 800 min -1
Drilling capacity in concrete ................................................................................................................................................................ 15 mm
Drilling capacity in brick and tile........................................................................................................................................................ 15 mm
Drilling capacity in steel..................................................................................................................................................................... 13 mm
Drilling capacity in Aluminium .......................................................................................................................................................... 15 mm
Drilling capacity in wood.................................................................................................................................................................... 30 mm
Drive shank ...................................................................................................................................................................................... 1/2“ x 20
Chuck neck diameter......................................................................................................................................................................... 43 mm
Weight without cable........................................................................................................................................................................ 1,9 kg
Noise/Vibration Information
Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (K=3 dB(A)).................................................................................................................................................. 94,2 dB (A)
Sound power level (K=3 dB(A)).................................................................................................................................................... 105,2 dB (A)
Wear ear protectors!
Total vibration values (vector sum in the three axes) determined according to EN 60745.
Vibration emission value ah
Drilling into metal............................................................................................................................................................................ 4,0 m/s2
Uncertainty K ................................................................................................................................................................................... 1,5 m/s2
Percussion drilling into concrete..................................................................................................................................................... 14,5 m/s2
Uncertainty K ................................................................................................................................................................................... 1,5 m/s2
14
14
GB
SPECIFIED CONDITIONS OF USE
The electronic drill/screwdriver can be universally used for drilling,
percussion drilling, screwdriving and cutting screw threads.
Do not use this product in any other way as stated for normal use.
MAINS CONNECTION
Connect only to single-phase AC current and only to the system
voltage indicated on the rating plate. It is also possible to connect
to sockets without an earthing contact as the design conforms to
safety class II.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is in
conformity with the following standards or standardized documents.
EN 60745, EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3, in
accordance with the regulations 2006/42/EC, 2004/108/EC
Rainer Kumpf
Manager Product Development
Authorized to compile the technical le
Winnenden, 2010-08-11
MAINTENANCE
The ventilation slots of the machine must be kept clear at all times.
If the machine is mainly used for percussion drilling, regularly
remove collected dust from the chuck. To remove the dust hold the
machine with the chuck facing down vertically, and completely open
and close the chuck. The collected dust will fall from the chuck. It is
recommended to regularly use cleaner (Id.No. 4932 6217 19) for the
clamping jaws and the clamping jaw borings.
Use only AEG accessories and AEG spare parts. Should components
need to be replaced which have not been described, please contact
one of our AEG service agents (see our list of guarantee/service
addresses).
If needed, an exploded view of the tool can be ordered. Please state
the Article No. as well as the machine type printed on the label
and order the drawing at your local service agents or directly at:
AEG Elektrowerkzeuge, Max-Eyth-Straße10, D-71364Winnenden,
Germany.
SYMBOLS
Please read the instructions carefully before
starting the machine.
CAUTION! WARNING! DANGER!
Always disconnect the plug from the socket before
carrying out any work on the machine.
Accessory - Not included in standard equipment,
available as an accessory.
Do not dispose of electric tools together with
household waste material! In observance of
European Directive 2002/96/EC on waste electrical
and electronic equipment and its implementation
in accordance with national law, electric tools that
have reached the end of their life must be collected
separately and returned to an environmentally
compatible recycling facility.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all times.
If the machine is mainly used for percussion drilling, regularly
remove collected dust from the chuck. To remove the dust hold the
machine with the chuck facing down vertically, and completely open
and close the chuck. The collected dust will fall from the chuck. It is
recommended to regularly use cleaner (Id.No. 4932 6217 19) for the
clamping jaws and the clamping jaw borings.
Use only AEG accessories and AEG spare parts. Should components
need to be replaced which have not been described, please contact
one of our AEG service agents (see our list of guarantee/service
addresses).
If needed, an exploded view of the tool can be ordered. Please state
the Article No. as well as the machine type printed on the label
and order the drawing at your local service agents or directly at:
AEG Elektrowerkzeuge, Max-Eyth-Straße10, D-71364Winnenden,
Germany.
15 15
AEG Elektrowerkzeuge
Max-Eyth-Straße 10
D-71364 Winnenden
Germany
www.aeg-pt.com
AEG Elektrowerkzeuge
Max-Eyth-Straße 10
D-71364 Winnenden
Germany
Table of contents
Other AEG Powertools Drill manuals
