AeroAudio HP AMP AES67 TM User manual

HP AMP AES67 TM
MANUAL
STEENWEG 148C - 9810 NAZARETH - BELGIUM - T [phone] - [e-mail]
The AeroAudio HPH AMP AES67 TM is a superb well designed studio quality class
AB headphone amplier made for Jocks and producers that hides away and just does
the job you need it for.
The +20 year eld proven design ensures your ears are safe from annoying cracking
audio on touching the volume knob. With a double output for both 3.5 and
6.3mm jack’s makes the annoying ‘where did I put it’ adapters obsolete, just simply
connecting all types of studio headphones. The rock solid miniature casing hides away
under your desk with a special design so your knees are safe from painfully bumping
it. A small bright shining LED let’s you nd the Amp instantly.
Three key features make this ampliers outstanding for studio use. The rst feature
is the high slew rate that prevents odd order distortion anomalies.
The second feature is current-on-demand at the output that enables the amplier
to respond quickly and linearly when necessary without risk of output distortion.
When large amounts of output power are suddenly needed, the amplier can
respond extremely quickly without raising the noise oor of the system and
degrading the signal-to-noise ratio.
The third feature is the gain-independent frequency response that allows the full
bandwidth of the amplier to be used over a wide range of gain settings.
WARINIG!
Without proper adjustment to the type of headphone used the HP-AMP-AES67 can produce over
100dBA @ +6dBU input level and can cause ear damage! Take proper precautions and make proper
settings to ensure the maximum legally allowed output level is not exceeded. AeroAudio strongly
advises to adjust input level to be set at 85dBA maximum output level on the headphone.
AeroAudio can not be held responsible for any type of damage or injuries in short- or long-term
caused by improper installation or use.

HP AMP AES67 TM
MANUAL
STEENWEG 148C - 9810 NAZARETH - BELGIUM - T [phone] - [e-mail]
Network setup
By default the HP-AMP-AES67 is shipped with DHCP on. Without a DHCP server in
the network, the AMP can be found using the Dante™ controller software. You can
use a direct cable connection between the computer and the AMP. Although a switch
can be used, it is not needed. The latest version of the Dante™ controller software
can be downloaded from the ofcial Audinate website at https://www.audinate.com.
Within the controller software you will nd the AMP using the “device info” section.
By double clicking the device (in red) you will nd the IP range of the AMP.
To change setting on the AMP you will need to match the IP address of the
computer to the range of the AMP. In this case 169.254.81.xxx
Dante™ controller
software

HP AMP AES67 TM
MANUAL
STEENWEG 148C - 9810 NAZARETH - BELGIUM - T [phone] - [e-mail]
Now set the computer running the controller software to match within the range of
the AMP. In this example we use 169.254.81.101 with subnet 255.255.0.0
Now the HP-AMP-AES67 will show in black and settings can be changed.

HP AMP AES67 TM
MANUAL
STEENWEG 148C - 9810 NAZARETH - BELGIUM - T [phone] - [e-mail]
By default AES67 is enabled. You can use the Ravenna RAV2SAP control software to
enable any AES67 streams to be shown in the Dante™ controller software.
The latest version of the RAV2SAP software and manual can be downloaded from
the ofcial Ravenna-network website at: www.ravenna-network.com.
Device conguration
The HP-AMP-AES67 supports sample rate conversion. Since by default AES67 is
enabled, this option is only available when AES67 has been disabled.
By default encoding is set to PCM 24 bit to match optimal encoding of the DA
converter.
Encoding can be changed but can result in loose of audio quality. AeroAudio strongly
advices to leave encoding at PCM24 bit.
Where needed Unicast delay requests can be enabled.
Delay is set by default to minimum at 1mS. This can be adjusted upto 5mS, but is not
recommended.
RAV2SAP
software

HP AMP AES67 TM
MANUAL
STEENWEG 148C - 9810 NAZARETH - BELGIUM - T [phone] - [e-mail]
Since the HP-AMP-AES67 is connected by a single network cable, redundancy is not
supported. Network settings can be changed to match the used AES67 or Dante™
network.

HP AMP AES67 TM
MANUAL
STEENWEG 148C - 9810 NAZARETH - BELGIUM - T [phone] - [e-mail]
Ethernet RJ45 AES67/Dante:
RJ45 Female
Power input 12 volt polarity unimportant.
Pin Function Type
1 TX + Data
2 TX - Data
3 RX + Data
4
5
6 RX - Data
7
8
Shield Shield Shield
RJ45 Female
Pin Functie Type
1
+5 tot +18 volt schakel contact Ingang
2
Massa Pin 1 Massa
3
Schakel contact Ingang
4
Massa Pin 3 Massa
5
Breath-functie Ingang
6
Massa Pin 5 Massa
7
n.c.
8
n.c.
9
n.c.
XLR 3 Pen Male
Pin Functie Type
1
Shield Shield
2
Signaal + Ingang
3
Signaal - Ingang
Connections: 6.35mm and 3.5mm stereo jack
Tip: Audio Left
Ring: Audio Right
Sleeve: Ground

HP AMP AES67 TM
MANUAL
STEENWEG 148C - 9810 NAZARETH - BELGIUM - T [phone] - [e-mail]
TECHNICAL SPECIFICATIONS
Power supply: 12 volt DC, 500mA
Power consumption: 150mA (nominal)
Maximum output power per channel @1Khz: 300mW at 32 ohm
Distortion @ 1Khz, 100mW: < 98dB
Channel separation @1Khz: < 101dB
Frequency response: 22Hz – 22KHz
Gain: -100 ~ 0dB
Encoding: PCM16, PCM24, PCM32
Sample rates: 44.1 KHz, 48KHz, 88.2KHz, 96KHz
Audio standard: AES67 and Dante™ enabled.

HP AMP AES67 TM
MANUAL
DIMENSIONS
135 mm * 76,3mm * 36mm
Weight: 0.3 Kg
STEENWEG 148C - 9810 NAZARETH - BELGIUM - T [phone] - [e-mail]
7,5 mm 7,5 mm
15 mm
11,3 mm
50 mm
120 mm
76,3 mm
135
36

HP AMP AES67 TM
MANUAL
Safety First!
- Caution: hot and sharp surfaces! This professional device may only be installed by qualied personnel.
- Check the cardboard box for any damage upon receipt of the goods. In case of a damaged box, please contact your distributor before opening it.
contact your distributor before opening the box.
- Read all documentation before using the unit.
- Keep all documentation for future reference.
- Keep the box and the packaging material even if the equipment has arrived in good condition.
- Should you ever need to ship the appliance, use only the original factory packaging.
- Do not spill water or other liquids in or on the device.
- Always use the power supply provided.
- Make sure that the power outlets correspond to the power requirements indicated on the back of the power supply.
- Do not use the device if the power cord is frayed or broken.
- Turn off and disconnect the devices from the mains before making any connections.
- Do not use the device near heaters, heating grills, radiators or other heat producing devices.
- Do not use the unit on a surface or in an environment that may interfere with the normal ow of air around the unit.
If the unit is used in an extremely dusty or smoky environment, the unit should be “dusted” regularly.
- Do not remove the cover. Removing the cover will expose you to potentially dangerous voltages.
- In case of malfunction, this unit should only be serviced by qualied service personnel.
- Always follow the instructions of the supplier and manufacturer - Only use accessories, spare and replacement parts specied by the manufacturer.
- Only use the device for the purpose intended by the manufacturer.
STEENWEG 148C - 9810 NAZARETH - BELGIUM - T [phone] - [e-mail]