AIR GREAN AG-WF16L02M User manual

SKU: AG-WF16L02M
READ AND SAVE THESE INSTRUCTIONS
Attention: Pictures in the manual are for reference only.

RULES FOR SAFE OPERATION
IMPORTANT SAFEGUARDS
Read Rules for Safe Operation and Instructions Carefully.
Caution
WARNING
1. This appliance has a polarized plug (one blade is wider than
the other). To reduce the risk of electric shock, this plug is
intended to fit in a polarized outlet only one way. If plug
does not fit fully in the outlet, reverse the plug. If it still does
not fit, contact a qualified electrician. Do not attempt to
defeat this safely feature.
2. To reduce the risk of fire or electric shock, DO NOT use this
fan with any solidstate speed control devices.
1. Never insert fingers, pencils, or any other object through the
grille when fan is running.
2. Disconnect fan when moving from one location to another.
3. Be sure fan is on a stable surface when operating to avoid
overturning.
4. DO NOT use fan in window, rain may create electrical hazard.
5. Household use only.
6. Ensure that the fan is switched off from the supply mains
beforeremovinh the grille.
1. This product employs overload protection (fuse). A blown fuse
indicates anoverload or short-circuit situation. If the fuse blows,
unplug the product from the outlet. Replace the fuse as per the
user servicing instructions (follow product marking for proper
fuse rating) and check the products. If the replacement fuse
blows, a short-circuit may be present and the product should
be discarded or returned to an authorized service facility for
examination and/or repair.
1
The rules about cord and plug as below

RULES FOR SAFE OPERATION
13
24
5
6
7
2. Do not operate any fan with a damaged cord or plug. Discard
fan or return to an authorized service facility for examination
and/or repair.
3. Do not run cord under carpeting. Do not cover cord with throw
rugs, runners, or similar coverings. Do not route cord under
furniture or appliances. Arrange cord away from traffic area
and where it will not be tripped over.
PART FIGURE
2
The rules about cord and plug as below

Clip
PART FIGURE
NO. Description NO. Description
1 Front Grill
2 Spinner
3 Blade
5 Rear Grill
4 Plastic nut
6 Motor shaft
7 Motor
GRILL & FAN BLADE ASSEMBLY
1. Unscrew the spinner clockwise (or take the spinner
out from the bag) and the plastic nut counterclockwise
to remove both of them. Fix the rear grill to the motor
then tighten the plastic nut again. (Fig. 1)
2. Insert the blade into shaft, and make sure the rotor
shaft pin is fitted into groove of the blade. Turn the
spinner counterclockwise to tighten the blade. (Fig. 2)
3. Fasten the front grill and the rear grill by the grill clip
(Fig. 3)
Fig.1
Fig.2
Fig.3
All the pictures in this manual are for explanation purpose only. Any discrepan-
cy between the real object and the illustration in the drawing shall be subject to
the real subject.
Note:
3

SPEED ADJUSTMENT
Adjust to the desired speed by pulling the switch cord (A).
0---Off 1---Low 2---Medium 3---High
OSCILLATION CONTROL
Pull switch cord (B) to start and stop oscillation.
TO ADJUST THE WIND DIRECTION
Push the guard lightly to the desired up or down direction.
The fan should be installed on a solid wooden or pillar which
stands vertically to the floor.
Caution : To prevent the fan from falling off, do not install it on
walls less then 10 cm thick or made of materials that are
easily damaged.
Installing the mounting bracket
Fix the supplied mounting bracket firmly to the wall using the
three screws.
Installing the stand
Mount the stand on the bracket by inserting the bracket catch
into the slot on the stand.
Fix the stand onto the bracket with a retaining nut.
OPERATING INSTRUCTION
4
The bracket should be positioned at least 35 cm from the ceiling and at least 30
cm from adjoining wall.
Note:
If the retaining nut does not pass through the holes, push the stand downwards
until it is fully mounted on the bracket.
Note:

1. Grasp plug and remove from the receptacle or
other outlet device. Do not unplug by pulling
on cord.
2. Open fuse cover. Slide open fuse access
cover on top of attachment plug towards blades.
3. Remove fuse carefully. Insert the tip of your tool
into fuse slot (close with the terminal), then prize
the fuse gradually and slowly, but not overexert. If you feel tight, you can try it at
several times and prize the fuse little by little. When one side of the fuse has
been prized, then you can get the fuse out entirely.
4. Risk of fire. Replace fuse only with 2.5 Amp, 125 Volt fuse.
5. Close fuse cover. Slide closed the fuse access cover on top of attachment plug.
6. Risk of fire. Do not replace attachment plug. Contains a safety device (fuse) that
should not be removed. Discard product if the attachment plug is damaged.
USER SERVICING INSTRUCTIONS
CLEANING
1. Be sure to unplug from the electrical supply source before cleaning.
2. Plastic parts should be cleaned with mild soap and a damp cloth or sponge.
Thoroughly to remove soap film with clean water.
3. Be sure not to make water or other liquid enter inside of motor.
Notice:
1. When you replace the fuse, please don’t operate suddenly or overexert, or else
the product will be damage or cause accident.
2. When you feel it hard to be operated, please make sure you have got the right
way.
5
1500 S. MILLIKEN AVE STE B.
ONTARIO, CA 91761 www.airgrean.com