Air Vent Mixflow ECIF40W-150 User manual

www.airvent.com.au
Owner’s Manual
ECIF40W-150 / ECIF40W-150T
ECIF50W-150 / ECIF50W-150T
ECIF200-PRO/ ECIF200-MAX
ECIF200-PRO
ECIF200-MAX
Mixflow Inline Fan
EC Greenline series
OWNER’S MANUAL
This manual focuses on the safety precautions in the installation, and the use and maintenance of the
product. It is important that these installation and maintenance instruction are fully adhered to, be sure to
read this manual carefully before installing and using this product.
• All electrical installations must be carried out by suitably qualified and competent personnel in accordance
with all statutory requirements.
• The fan is designed for use in an ambient temperature of up to 40-degree. It is not suitable for corrosive or
explosive atmospheres.
• The installer should provide easy access to the fan to facilitate future maintenance and ensure that the fan
is adequately supported.
• This product is not intended for use by persons (including children) with reduced physical sensory or
mental capabilities or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the product by a person responsible for their safety. Children should be
supervised to ensure that they do not play with the product.
• Precautions must be taken to avoid back-flow of gases into the room from the open flue of gas or other fuel
burning appliances.
• A minimum of one (1) metre of duct is to be fitted to the fan inlet and discharge spigots.
WARNING
PRODUCT SPECIFICATIONS
Model Height Width Length
ECIF40W-150 208.5mm
208.5mm
208.5mm
208.5mm
208.5mm
225mm
225mm
315mm
315mm
315mm
60mm
60mm
60mm
2.3kg NA
NA
Ext.
1-60mins
1-60mins
2.3kg
81mm
81mm
81mm148
148
148
225mm
225mm 315mm
315mm
60mm
60mm
2.53kg
2.53kg
81mm
81mm148
196
148
225mm
ECIF50W-150
ECIF40W-150T
ECIF50W-150T
233.8mm 249mm 330mm 100mm 80mm 3.62kg
Weight Run On
Timer
Spigot
Diamete
Junction
Box
Pre-drill
hole
Distance
233.8mm
249mm 330mm
80mm
100mm
196

WARNING
This is a plug & go product, no further wiring is required.
Please ensure colour code is followed When Wiring，incorrect Wiring will result in damaged ROT PCB
Board and will void warranty.
For build-in ROT Fans only
Non ROT
Version
ROT
Version
Wall Plug
• Airvent Australia Pty Ltd warrants this product to be free of defects in material and workmanship for the applications specified in
the Owner’s Manual for a period of one year from date of purchase.
• This warranty only applies to the original purchaser of this product.
• This warranty excludes damage, accidental or otherwise, to the unit not caused by a defect in material or workmanship.
• The warranty also excludes damage caused by misuse, tampering modification, misassemble, repairs, or alteration or failure to
adequately maintain and care for the unit. Operating this product under any conditions other than those recommended or at
voltages other than indicated will also void this warranty. For warranty issues, contact the place of purchase for repair/replacement
opportunities. The original date receipt or proof of purchase must accompany all returns.
• All warranties expressed or implied are limited for one year from the date of purchase. Airvent is a register trademark of AIRVENT
AUSTRALIA PTY LTD. Unless prescribed by law, AIRVENT shall not be liable for any personal injury, property or any incidental or
consequential damage of any kind resulting from malfunctions, defects, misuse, improper assembly or installation, or alteration of
this product.
• For further warranty clarification, please visit our website on www.airvent.com.au or email us on [email protected].
Upon receipt, please check carefully whether the product is consistent with your order, the fan should be inspected in
case of any damage. Ensure the product specifications and product tags correspond to the correct power and voltage
standards of the country the fan is being used in.
Warning: The fan must be isolated from the power supply during installation and maintenance.
① Remove the fan body from the spigots that are
attached to the base by releasing the two retaining
clamps.
③Re-mount the fan body in-between the spigots
by lining up the retaining clamps.
④Tighten the two retaining clamps ensuring the
body is tightly fastened.
② Mount the base in the desired position using the
fasteners supplied
BEFORE STARTING WIRING Diagram
—ECIF40W-150 / ECIF50W-150
WIRING Diagram
INSTALLATION
Main
Frame
ImpellerHoops Hoops Duct
Insert 1
Duct
Insert 2
Spigots
Base plate
SUPPORT & LIMITED ONE-YEAR WARRANTY
One
Year
—ECIF40W-150T / ECIF50W-150T