AIRMAC DBMX200 User manual

Diann Bao Inc.
www.airmac.com.tw E-mail: [email protected] Tel: [phone]
Fax: [phone]
Linear Air Pump
Model No. DBMX200
Performance / Rendimiento / Prestanda
★Allowance：±5%
Performance Curves DBMX200
0
50
100
150
200
250
300
0 0.1 0.2 0.3 0.4 0.5
Pressure = kg / cm
2
Q = L / Min.
110~120V 60Hz
220~240V 50Hz
Exhaust
Dimensions / Dimensioner （mm）
Operating range：0.1 to 0.25 kg/cm2
Model No. Voltage
(VAC)
Frequency
(HZ)
Rated
Pressure
(kg/cm2)
Airflow
(LPM)
AMP
(A)
WATT
(W)
DBMX200 110 ~ 120 60 0.2 200 3.2 190
DBMX200 220 ~ 240 50 0.2 200 1.75 186
< 47 dBA 20 - 80
-10
oC 11.9 kg
+40
v170310

DBMX version series 150、200、DBMXL120
NO. DESCRIPTION QTY
1 TOP SCREW 1
2 FILTER COVER 1
3 FOAM SEAL 1
4 FILTER 1
5 UPPER HOUSING 1
6 SAFETY SYSTEM NUT 1
7 COIL COVER 1
8 SAFETY SYSTEM KIT 1
9 THERM
A
L PROTECTOR 1
10 ELECTROMAGNET 2
11 WIRE STOPPER 1
12 COIL FRAME 1
13 VIBRATION CONTROL RUBBER 4
14
A
CTIVATING ARM 1
15 DIAPHRAGM 2
16 DIAPHRAGM FRAME 2
17 U
–
NUT 2
18 DIAPHRAGM HOUSING 2
19 CHECK VALVE 8
20 GASKET
–
1 2
21 L
–
TUBE 2
22 DIAPHRAGM HOUSING COVER 2
23 POWER CORD 1
24 CORD PROTECTOR 1
25 STEEL PLATE 1
26 GASKET
–
2 1
27 LOWER HOUSING 1
28 RUBBER FEET 4

Figure 1
Figure 3
Maintenance Manual
DBMX version 150、200、DBMXL120
1. To clean the air filter（Recommended once every six months）
A. Loosen the screw on top. (As shown in Figure1)
B. Remove filter cover.
C. Take the filter out and clean it with clean water and dry it.
D. Put it back and secure the fixing plate with the screw in.
2. To change the diaphragms
IMPORTANT：To open the upper housing, please make sure you
have unplugged the power cord before opening.
As rare earth is applied on magnets of the activating
arm on models DBMX150, DBMX200, DBMXL120 please
be very careful after you have disassembled these
parts—Do NOT allow the magnets to come into contact with any electronic
devices, the watch on your wrist, cell phones, etc.
DYSFUNCTION OF THE MENTIONED OBJECTS OR DEVICES CAN
RESULT FROM THE CONTACTS.
ALWAYS use the fixture we have included when locating activating arm to
the center spacing between the two electromagnets.
A. Loosen the four screws around the aluminum upper housing, and take the housing off. (As shown in figure 2)
B. Loosen the four screws around the coil cover, and take the cover off. (As shown in figure 3)
C. Loosen the four screws and disassemble the diaphragm housing.
D. Loosen the u-nut in the center of diaphragm.
E. Take the diaphragm off its place.
F. Replace a new one by mounting the rubber studs into their position.
G. Press the rim of the diaphragm into the ring.
H. Secure the magnet with a new u-nut and screw and put the diaphragm
housing back with the four screws on.
I. Put the coil cover back with the four screws on.
J. Put on the aluminum cover and secure the four screws firmly.
Figure 2