AirStage UTY-RSKY User manual

OPERATING MANUAL
TM
SIMPLE REMOTE CONTROLLER
P/N 9371069029-05
OPERATING TIPS
Cooling / heating priority
(AIRSTAGE™ (V-II Series Heat Pump model only))
If another indoor unit in the same system is already operating in the•
cooling mode or dry mode, heating mode settings cannot be performed.
An indoor unit that is set up as an Administrative Indoor Unit can•
operate in the AUTO mode.
Administrative Indoor Unit:•
Special indoor unit is not restricted by the switching of cooling and
heating described above.
TROUBLE SHOOTING
Before requesting service, perform the following checks:
Symptom Problem
Doesn’t
operate
at all.
Has there been a power failure?•
Has a fuse blown out, or a circuit breaker been•
tripped?
Is the main power switch set to the OFF position?•
It is being controlled centralized?•
If the problem persists after performing these checks, or if you notice
burning smells, or the operation lamp ashes, immediately stop operation,
turn off the electrical breaker and consult authorized service personnel.
SPECIFICATIONS
MODEL UTY-RSKY/
UTY-RSKG/
UTY-RSKYT
POWER DC12V
DIMENSION & WEIGHT
HEIGHT 120 mm
WIDTH 75 mm
DEPTH 14 mm
WEIGHT UTY-RSKY/
UTY-RSKG 90 g
UTY-RSKYT 100 g
SAFETY PRECAUTIONS
The “SAFETY PRECAUTIONS” indicated in this manual contain important information pertaining to•your
safety. Be sure to observe them.
For d•etails of the operation methods, refer to this manual.
Request•the user to keep this manual on hand for future use, such as for relocating or repairing the unit.
WARNING
This mark indicates procedures which, if improperly performed, might lead to the death or
serious injury of the user.
In the event of a malfunction (burning smell, etc.),•
immediately stop operation, turn off the electrical
breaker, and consult authorized service personnel.
Do not repair or modify any damaged cable by•
yourself. Let the authorized service personnel to
do it. Improper work will cause a electric shock or a
re.
This unit contains no user-serviceable parts.•
Always consult authorized service personnel for
repairs.
When moving, consult authorized service personnel•
for disconnection and installation of this unit.
Do not touch with wet hands. It may cause an•
electric shock.
If children may approach the unit, take•
preventive
measures so that they cannot reach the unit.
Do not repair or modify by yourself. It may cause a•
fault or accident.
Do not use ammable gases near this equipment. •
It may cause a re from leaking gas.
CAUTION
This mark indicates procedures which, if improperly performed, might possibly result in
personal harm to the user, or damage to property.
Do not set vessels containing a liquid on this unit.•
Doing so will cause heating, re, or electric shock.
Do not expose this unit directly to water. Doing so•
will cause trouble, electric shock, or heating.
Dispose of the packing materials safely. Tear and•
dispose of the plastic packing bags so that children
cannot play with them. There is the danger of
suffocation if children play with the original plastic
bags.
Do not place electrical devices within 1 m of this•
unit. It may cause malfunction or failure.
Do not use re near this unit or place a heating •
apparatus nearby. It may cause malfunction.
Do not touch the switches with sharp objects.•
Doing so will cause injury, trouble, or electric shock.
AIR CONDITIONER
English
KEEP THIS MANUAL FOR
FUTURE REFERENCE
9371069029-05_OM_EN.indd 1 31/7/2555 13:33:56

Press the “ ” button or “ ” button to set the room
temperature while in operation.
TEMPERATURE
NOTES
* A heat pump model that is not set up as an Administrative
Indoor Unit cannot operate in the AUTO modes.
** FAN cannot be selected for a heat pump model.
Refer to details in the Administrative Indoor Unit OPERATING TIPS.
*** Heating operation can not be performed in the
"COOLING-ONLY" models.
If the priority mode is set to “Priority on Administrative•
Indoor Unit”, the operating mode of other indoor units
except Administrative Indoor Unit will be controlled by
an Administrative Indoor Unit.
If the operating mode of Administrative Indoor Unit is set to “AUTO”, “AUTO” is•
displayed in addition to the indicator of current operating mode on other wired
remote controllers except Administrative Indoor Unit. In this case, operation of
other indoor units is controlled by the Administrative Indoor Unit.
Ex. : When operating mode of the Administrative Indoor
Unit is set to “AUTO” while air conditioning setting.
(The indication on other wired remote controllers except
Administrative Indoor Unit).
OPERATION
If an error occurs, the following indicator will be shown.
(“ ” will appear in the set room temperature indicator.)
If “ ” is displayed, immediately contact autho-
rized service personnel. Do not used the operation
as shown to the right if an error has occurred.
Occurrence of an error is indicated by the blinking of
operation lamp.
ERROR CODE
(1) When is displayed, there are functions for which settings cannot be made.
When a button is pushed to change a restricted setting, will ash.
(2) When is displayed, some operation are restricted. In such case, contact the administrator.
(3) During Automatic Defrosting operation and Oil Recovery operation, will be displayed on
the remote controller.
(4) •
When “ ” or “ ” is indicated on the temperature indicator, it means under maintenance.
• When “ ” is indicated on the temperature indicator, anti freeze function is activated.
However, this function cannot be operated by the remote controller.
NOTES
Press the “ ” button to select the fan speed while in
operation.
(Select the fan speed
automatically.)
(AUTO) (HIGH) (MED) (LOW)
FAN SPEED
NOTES
Press “ ” button to select the operation mode while in operation.
OPERATION MODE
(AUTO) (COOL) (DRY) (FAN) (HEAT)
NOTES
Error code
Ex. Error code
When Administrative Indoor Unit is set to “AUTO”.
* **
Each press of the “ ” button alternates operation and stop.
When operating, operation lamp (green) will light up.
START / STOP
(5) Preset values are displayed when the “ ” button, the
“” button or “ ” button, the “ ” button is pressed
while stopping.
(6)
Mode indication blinks when inoperative setting of indoor unit is made.
(7) Blinking of the fan speed indicator means the timing for lter
cleaning of the indoor unit.
To erase indication, press the “ ” button for more than 2 seconds.
Faulty unit No.
(0-15, C0)
Fan speed indicator
Instructions on heating are not applicable for the "COOLING-ONLY" models.
Temperature setting range
* Room temperatures as low as 10 to 15 °C cannot be set depending on the
model. (Heating)
* The temperature setting should be considered a standard value, and may
differ somewhat from the actual room temperature.
AUTO • • • • • • • • • • • • • 18 to 30°C
COOL/DRY • • • • • • • • • 18 to 30°C
HEAT • • • • • • • • • • • • • 10 to 30°C
***
9371069029-05_OM_EN.indd 2 31/7/2555 13:33:58