aiTerminal AIT003B User manual

Electric Standing Desk
User Manual
Model: AIT003B

TABLE OF CONTENTS
Parts and Hardware List
Parts
01
02
Hardware 02
Step 1 03
Step 2 04
Step 3 04
Step 4 05
Step 5 05
Step 6 06
06Step 7
07Step 8
07Step 9
08
Step 10
09Operation Guide

01
PARTS AND HARDWARE LIST
NO Component Name Qty
Control Box
Key Pad
M6*12 Screws
ST4.8*16 Screws
Leg
Monitor Arm
Bracket
Side Bracket
U Shape Base
M4*12 Screws
5mm Hex Spanner
4mm Hex Spanner
M5*8 Screws
M6*8 Screws
1
2
3
4
5
6
7
8
A
B
C
D
E
F
G
1
1
2
1
2
Wirebox 1
1
1
Upper Surface
91
Lower Desk
10 1
Motor Cover
11 1
Reinforce Plate
12 1
Knob
13 4
2
ST3.5*19 Screws
H2
Cable Tie
I4
10
1
12
1
6
6
2
4
5
6
78
3
12
10
11
9
13
1
A B C D
EFGH
I

PARTS
HARDWARE
6 Wirebox x1
2 U Shape Base x1
7 Monitor Arm x1 8 Leg x1
11 Motor Cover x110 Lower Desk x1
3 Side Bracket x2 4 Key Pad x1
9 Upper Surface x1 12 Reinforce Plate x1
13 Knob x4
4mm Hex
Spanner x 1
5mm Hex
Spanner x 1
M6*8
Screw x 6
M6*12
Screw x 10
ST4.8*16
Screw x 14
ST3.5*19
Screw x 2
M5*8
Screw x 2
M4*12
Screw x 12
1 Control Box x1
5 Bracket x 2
Cable Tie x 5
02
A B C D
IGF HE

Attach the leg to the U shape base using 4 pcs M6*12 screws.
STEP 1
4mm Hex Spanner
M6*12 screw 4pcs
03
Tool Required：A
Hardware Required：
C Screws

Attach the left bracket and the right bracket to the leg using 2 pcs
M6*8 screws on the back first and using 6 pcs M6*12 screws on
the top.
STEP 2
STEP 3
Pull out the motor cable under the foot. Attach the motor cover to the
foot using 4 pcs M6*8 screws and the reinforce plate to the foot using
2 pcs M5*8 screws.
M6*8 screw 4pcs M5*8 screw 2pcs
4mm Hex Spanner
M6*8 screw 2 pcs
M6*12 screw 6 pcs
4mm Hex Spanner
04
Tool Required：A
Hardware Required：
D&E Screws
Tool Required：A
Hardware Required：
C&D Screws

ST4.8*16 screw
2pcs
ST3.5*19 screw
2pcs
STEP 4
Attach the control box and the hand controller to the upper surface,
using 2 pcs ST4.8*16 screws for the control box and 2 pcs ST3.5*
19 screws for the keypad.
Plug the cord from the motor to the control box and the cord from
the control box to the hand controller. Arrange the cords neat if in
the wire box, then attach the box to the upper surace using 2 pcs
ST4.8*16 screws.
STEP 5
ST4.8*16 screw
2 pcs
05
Tool Required：Drill / Driver
Hardware Required：
G&H Screws
Tool Required：Drill / Driver
Hardware Required：
G Screws

ST4.8*16 screw
4 pcs
Attach 6 pcs ST4.8*16 screws to fasten the side brackets to the
lower desk.
STEP 6
STEP 7
Lay the U shape base down on the floor as photo. Attach the upper
surface to the side brackets using 4 pcs ST4.8*16 wood screws
and place rubber pad between them.
ST4.8*16 screw
6 pcs
06
Tool Required:Drill / Driver
Hardware Required：
G Screws
Tool Required：Drill / Driver
Hardware Required：
G Screws

Fasten the knob first, then attach the two side brackets to the left
and right brackets. Tighten the knob to secure the side brackets.
STEP 8
STEP 9
Attach the monitor mount to your LCD.
M4*12 screw 12 pcs
07
Tool Required：A
Hardware Required：
F Screws
4mm spanner

STEP 10
Turn the desk upright. Loosen the screws then put the monitor onto
the leg. Adjust the height then fasten the screws. Use cable to hold
the spare cable in place.
Cable Tie 5 pcs
08
Hardware Required：I

Operation Guide
09
Initialization of the parallel systems
Step 1: Power on
Step 2: Press up and down key together for about 30s until you hear a “ beep” then press
down button to finish resetting.
After that, you can use this height adjustable desk now.
You have to do the initialization when meet the following situations.
1. After the Linear Actuators have been installed into the table.
2. Table has been moved.
3. Some failures occurred.
Reset
Same as step 2