manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. aizo
  6. •
  7. Server
  8. •
  9. aizo digitalSTROM-Server Quick start guide

aizo digitalSTROM-Server Quick start guide

aizo ag
www.aizo.com
digitalSTROM-Server dSS11-1GB
Montageanleitung für den Elektroinstallateur
Installation notes for electricians
Instructions d‘installation pour l‘électricien
Istruzioni di installazione per l‘elettricista
IN
Ethernet
LED
B
-
dSS
1GB
A
+
USB 1
USB 2
dS485Bus
-24V+
B
-
A
+
654
321
dS485Bus
Power
Supply
230 V
24 V
DC AC
+-
B
-
A
+
L N
+-
B
-
A
+
654
321
max. 62 dSM
max. 1 dSS-1GB
Ethernet
IN
B
-
A
+321
...
24 V
B
-
A
+321
-24V+
1GB
120 120
8 mm
6 mm
1
2
1.5 ... 4 mm²
0.6 ... 0.8 mm²
1
2
0.5 Nm
1
B
-
dSS
1GB
A
+
17.5 mm 70 mm
90 mm
1
2
35 mmEN50022
-24V+
DEUTSCH
Funktion und Verwendungszweck
Der digitalSTROM-Server (dSS) ist mit allen digitalSTROM-Metern (dSM) über den
dS485 Bus verbunden. Im digitalSTROM-Server läuft ein Web-Server (digital-
STROM-Konfigurator) auf den mit einem PC/Notebook über das Ethernet-Netzwerk
zugegriffen werden kann. Die Inbetriebsetzung erfolgt gemäss Anleitung im
digitalSTROM-Installationshandbuch.
Werkseinstellungen:
Username: dssadmin Passwort: dssadmin
Lebensgefahr!
Berühren der elektrischen Hausinstallation unter Spannung
(230 V AC) kann zum Tod oder zu schwersten Verbrennungen
führen.
Vor der Installation dieses Gerätes alle Zuleitungen spannungslos
schalten und prüfen, ob Spannungsfreiheit besteht. Einschalten
der Spannung durch Dritte verhindern.
Wichtige Hinweise
Nur geschultes Fachpersonal darf das Modul installieren und in
Betrieb nehmen. Landesspezifische Vorschriften sind einzuhal-
ten.
Das Gerät darf nur in trockenen und geschlossenen Räumen
betrieben und nicht zu direkt oder indirekt gesundheits- oder
lebenssichernden Zwecken benutzt werden oder zu Zwecken, bei
denen ein Ausfall des Gerätes zu Gefahren für Menschen, Tiere
oder Sachwerten führen kann.
Vor der Inbetriebnahme ist sicherzustellen, dass
– der Netzanschluss fachgerecht ausgeführt und der Schutz gegen elektrischen
Schlag sichergestellt ist,
– das Gerät nach den Bestimmungen der EN 60950 außerhalb der Stromversorgung
spannungslos schaltbar ist (z.B. durch den primärseitigen Leitungsschutz),
– alle Zuleitungen ausreichend abgesichert und dimensioniert sind,
– nach der Installation der Klemmenbereich abgedeckt wird, um unzulässiges Be-
rühren spannungsführender Teile zu vermeiden (z.B. Einbau im Schaltschrank).
Montage:
Anschlussklemmen oben und unten. Für ausreichende Konvektion wird die Einhal-
tung eines Mindestabstands zu anderen Modulen von 3 cm oberhalb und unterhalb
des Gerätes empfohlen. Die 24V Spannungsversorgung erfolgt über die entspre-
chend gekennzeichneten Schraubanschlüsse. Der dS485 Bus wird über die Ein/
Ausgänge A und B angeschlossen. Eine korrekte Polung (A-A, B-B) ist erforderlich.
Die bidirektionale 2-Draht-Schnittstelle dient der Vernetzung mit bis zu 62 dSM. Es
kann immer nur ein dSS pro dS485 Bus angeschlossen werden. Es sind 120 Ohm
Abschlusswiderstände jeweils an den Enden der dS485 Bus-Verkabelung erfor-
derlich. Diese sind der Verpackung beigelegt. dS485 Bus Drähte müssen verdrillt
sein. Der Tastereingang „IN“ löst einen Event aus, der für spätere Erweiterungen
verwendet werden kann. Empfehlung für Ethernetkabel: Kabel ohne Schirmung
verwenden.
Weiterführende Informationen zur Inbetriebsetzung finden Sie im digitalSTROM-
Installationshandbuch oder unter www.digitalstrom.org/support.
Gewährleistung:
aizo ag gewährt auf dieses Produkt eine mängelfreie Funktionalität gemäss Spe-
zifikation während einer Frist von 24 Monaten ab Lieferung durch aizo ag. Durch
Öffnen des Gerätes, sonstige Geräteeingriffe oder unkorrekte Installation/Konfigu-
ration erlischt die Gewährleistung.
Technische Daten
Bezeichnung ............................................................digitalSTROM-Server
Typenbezeichnung ...................................................dSS11-1GB
Hersteller.................................................................aizo ag
Nenneingangsspannung..........................................24 V DC (+/- 10 %), min. 0,4 A
Leistungsaufnahme ohne USB................................max. 2,5 W
USB Schnittstelle.....................................................2 x Typ A Buchse, USB 2.0 Full-
Speed, max. 0,5 A @ 5 V pro Port
Ethernetschnittstelle...............................................RJ45 10/100 Mbit/s
Datenübertragung via dS485 Bus............................dS485 Protokoll V1.0 / EIA485
Schutzart..................................................................IP20 EN 60529
Zulässige Umgebungstemp. (Betrieb/Lagerung) ...-20 °C ...+45 °C/-20 °C ...+70 °C
Zulässige Feuchtigkeit (Betrieb)..............................nur in trockenen Räumen
Gewicht ohne Verpackung .......................................ca. 0,07 kg
dSFdSF dSF
NL3L2L1 PE
L3
L2
L1 L3L2L1 L1
L3L2L1 L3L2L1 L1N
dSMdSMdSMdSMdSMdSMdSM
dSS
1GB
LED grün ..................... Betriebsbereit
rot......................... Hardware-Fehler
blau-gelb ............. Software-Aktualisierung
grau...................... keine Verbindung auf dS485
Taster 5 Sek. drücken..... Neustart (Taster unter der LED)
15 Sek. drücken... Zurücksetzten auf Werkseinstellungen
(username/passwort, DHCP)
Technische Änderungen vorbehalten. Neueste Informationen finden Sie auf unserer Webseite.
Dok. Nr. A0935D003V003/ 2012-04-26
EN 55022
EN 61000-6-2
EN 61000-6-3
ENGLISH FRANCAIS ITALIANO
Fonctionnement et domaine d‘application
Le digitalSTROM-Server (dSS) est relié à tous les digitalSTROM-Meter (dSM) par le biais
du bus dS485. Un serveur Web (configurateur digitalSTROM) fonctionne sur le digital-
STROM-Server (digitalSTROM) auquel il est possible d‘accéder avec un PC/Notebook par
le réseau Ethernet. La mise en service doit être effectuée selon les instructions du manuel
d‘installation digitalSTROM.
Paramètres d‘usine:
Nom utilisateur: dssadmin Mot de passe: dssadmin
Danger de mort!
Tout contact avec une installation intérieure électrique sous tension
(230 V AC) peut entraîner des blessures graves, voire même la mort.
Avant d'installer cet appareil, mettre toutes les lignes d'alimentation
hors tension et vérifier l'absence de tension. Empêcher toute mise
sous tension par une tierce personne.
Remarques importantes
Seuls des spécialistes formés sont autorisés à installer ce module et à
le mettre en service. Respecter les directives nationales en vigueur.
L‘appareil ne doit être utilisé que dans des locaux secs et fermés et
non à des fins (directement ou indirectement) à risque pour la santé ou
pouvant entraîner la mort, ni à des fins pour lesquelles une panne de
l‘appareil peut présenter un danger pour les personnes, les animaux
ou les biens matériels.
Avant la mise en service, s‘assurer que
– le raccordement au réseau est réalisé de manière conforme et protégé contre les chocs
électriques,
– l‘appareil peut être mis hors tension selon les dispositions de la norme EN 60950 hors
de l‘alimentation (par ex. via le disjoncteur du côté primaire),
– toutes les lignes d‘alimentation sont suffisamment sécurisées et dimensionnées,
– les bornes sont recouvertes après le montage afin d‘éviter tout contact avec des élément
sous tension (par ex. montage dans l‘armoire électrique).
Montage:
Bornes de raccordement en haut et en bas. Pour obtenir une convection suffisante, il con-
vient de respecter une distance minimale de 3cm avec les autres modules, au-dessus et
en-dessous de l‘appareil. L‘alimentation électrique 24 V s‘effectue par le biais des bornes
à vis. Le bus dS485 est raccordé par les entrées/sorties A et B. Respecter la polarité cor-
recte (A-A, B-B).. L‘interface à deux fils bidirectionnelle sert à la mise en réseau de jusqu‘à
62 dSM11. Seulement un dSS11 peut être raccordé par bus dS485. Des résistances de
terminaison 120 Ohm sont nécessaires à chaque extrémité du câblage bus dS485. Celles-
ci sont jointes à l‘emballage. Les fils bus dS485 doivent être torsadés. Le bouton-poussoir
extérieur en option (IN) à l‘entrée 5 déclenche un événement pouvant être configuré dans
le configurateur digitalSTROM. Il est recommandé d‘utiliser un câble Ethernet non blindé.
Attention! Respecter la polarité correcte des fils sur le bus dS485 (A-A, B-B).
Vous trouverez de plus amples informations sur la mise en service dans le manuel
d‘installation digitalSTROM ou sur : www.digitalstrom.org/support.
Garantie des vices cachés:
aizo ag assure un parfait fonctionnement du produit conformément à la spécification
pendant une durée de 24 mois après livraison par aizo ag. L‘ouverture de l‘appareil, toute
tentative d‘ouverte de l‘appareil ou une installation/configuration incorrecte annulent la
validité de la garantie.
Caractéristiques techniques
Désignation.......................................................... digitalSTROM-Server
Indication de type................................................. dSS11-1GB
Fabricant.............................................................. aizo ag
Tension d‘entrée nominale .................................. 24 V DC (+/- 10 %), 0,4 A min.
Puissance absorbée sans USB............................ 2,5 W max.
Interface USB....................................................... 2 x prise USB type A, USB 2.0 Full-Speed,
0,5 A max. à 5 V par port
Interface Ethernet................................................ RJ45 10/100 Mbit/s
Transfert de données par bus dS485................... Protocole dS485 V1.0 / EIA485
Protection............................................................. IP20 EN 60529
Temp. ambiante admiss. (service/stockage)....... -20 °C ...+45 °C/-20 °C ...+70 °C
Humidité admiss. (service).................................. seulement dans loceaux secs
Poids sans emballage.......................................... 0,07 kg env.
LED vert......................................... prêt au fonctionnement
rouge...................................... erreur matérielle
bleu-jaune.............................. mise à Jour du logiciel
gris......................................... pas de connexion à dS485
Bouton- maintenir appuyé 5 sec. ........ redémarrer (bouton-poussoir sous LED)
poussoir maintenir appuyé 15 sec. ...... réinitialiser les paramètres d‘usine
(nom utilisateur/mot de passe, DHCP)
Funzione e impiego previsto
Il
digitalSTROM-Server
(dSS) è connesso a tutti i digitalSTROM-Meter (dSM) attraverso il
bus dS485. Il
digitalSTROM-Server
utilizza un server web (configuratore digitalSTROM) a cui
è possibile accedere da un PC/ notebook attraverso la rete Ethernet. La messa in funzione
avviene secondo le istruzioni contenute nel manuale di installazione digitalSTROM.
Impostazioni di fabbrica:
Username: dssadmin Password: dssadmin
Pericolo di morte!
Toccare un impianto elettrico interno sotto tensione (230 V AC) può
causare la morte o ustioni gravi.
Prima di installare questo dispositivo, mettere tutti i cavi di aliment-
azione fuori tensione e controllare che la tensione sia effettivamente
assente. Impedire la messa in tensione da parte di terzi.
Indicazioni importanti
Il modulo deve essere installato e messo in funzione solo da personale
tecnico specializzato e appositamente formato. Osservare le direttive
specifiche vigenti a livello nazionale.
il dispositivo deve essere attivato solo in ambienti chiusi e asciutti e
non deve essere utilizzato né direttamente né indirettamente per la
protezione della vita o della salute o per qualsiasi altra finalità per cui
un guasto del dispositivo stesso possa determinare un pericolo per
persone, animali o beni materiali.
Prima della messa in funzione, assicurarsi che
– la connessione alla rete sia realizzata in modo conforme e la protezione contro la scossa
elettrica sia assicurata,
– sia possibile mettere il dispositivo fuori tensione secondo le disposizioni EN 60950 al di
fuori dell‘alimentazione elettrica (ad es. attraverso la protezione della linea di aliment-
azione primaria),
– tutti i cavi di alimentazione siano correttamente dimensionati e messi in sicurezza,
– la zona dei morsetti risulti coperta dopo l‘installazione, per evitare il contatto con com-
ponenti in tensione (ad es. grazie al montaggio nell‘armadio elettrico).
Montaggio:
Morsetti in alto e in basso. Per una sufficiente convezione si raccomanda di mantenere una
distanza minima rispetto agli altri moduli di 3 cm al di sopra e al di sotto del dispositivo.
L‘alimentazione da 24V avviene attraverso i morsetti contrassegnati nel modo corrispon-
dente. Il bus dS485 è connesso attraverso le entrate/uscite A e B. È necessario rispettarne
la corretta polarità (A-A, B-B). L‘interfaccia bifilare e bidirezionale serve ad interconnettere
fino a 62 dSM. Può essere connesso solo un dSS per bus dS485. Sono necessari resistori
terminali da 120 Ohm per ogni estremità dei cavi bus dS485. Questi sono inclusi nella
confezione. I fili bus dS485 devono essere ritorti. Il tasto esterno opzionale (IN) all‘entrata
5 provoca un evento che è configurabile nel configuratore digitalSTROM. Si consiglia di
utilizzare un cavo Ethernet non schermato.
Attenzione! Rispettare la corretta polarità dei fili del bus dS485 (A-A, B-B).
Ulteriori informazioni sulla messa in funzione sono reperibili nel manuale di installazione
digitalSTROM o in www.digitalstrom.org/support.
Garanzia:
Per questo prodotto, la aizo ag garantisce un perfetto funzionamento, conforme alle speci-
fiche tecniche, per un periodo di 24 mesi dal momento della consegna da parte della aizo
ag. L‘apertura del dispositivo, altri interventi su di esso o un‘installazione/configurazione
scorretta annullano la validità della garanzia.
Dati tecnici
Denominazione ........................................................digitalSTROM-Server
Designazione del tipo...............................................dSS11-1GB
Produttore................................................................aizo ag
Tensione nominale di entrata ..................................24 V DC (+/- 10 %), min. 0,4 A
Potenza assorbita senza USB..................................max. 2,5 W
Interfaccia USB........................................................2 x presa USB tipo A, USB 2.0 Full-Speed,
max. 0,5 A @ 5 V per porta
Interfaccia Ethernet.................................................RJ45 10/100 Mbit/s
Trasmissione dei dati attraverso bus dS485 ...........Protocollo dS485 V1.0 / EIA485
Protezione................................................................IP20 EN 60529
Temp. ambiente ammessa
(funzionamento/conservazione) .............................-20 °C ...+45 °C/-20 °C ...+70 °C
Umidità ammessa (funzionamento) ........................solo in ambienti asciutti
Peso senza imballaggio...........................................circa 0,07 kg
LED verde ............................pronto al funzionamento
rosso ............................errore hardware
blu-giallo......................aggiornamento software
grigio............................nessuna connessione a dS485
Tasto premere per 5 sec. ......riavvio (tasto sotto il LED)
premere per 15 sec. ....reset delle impostazioni di fabbrica
(username/password, DHCP)
Function and intended use
The digitalSTROM-Server (dSS) is connected to all digitalSTROM-Meters (dSM) via the
dS485 bus. The digitalSTROM-Server runs a web server (digitalSTROM configurator) which
can be accessed from a PC/notebook via the Ethernet. Commissioning of the device is
described in the digitalSTROM installation manual.
Factory defaults:
User name: dssadmin Password: dssadmin
Warning: High voltage
Contacting or touching the electrical wires (230V AC) may cause
electrical shock and injury. Disconnect power before servicing. Prevent
others from reconnecting the device.
Important notes
Only trained experts are authorised to install and commission the
module. Country-specific regulations must be adhered to.
The device may only be operated in dry, closed rooms and must not be
used directly or indirectly for health or life-saving purposes or for pur-
poses where a device failure could lead to danger for people, animals
or material property.
Prior to commissioning, ensure that
– the mains connection is made properly and professionally and protection against electric
shock is ensured,
– the device can be made voltage-free outside the power supply according to
EN 60950 (e.g. circuit breaker on primary side),
– all supply lines are sufficiently protected and dimensioned,
– the terminal area is covered after installation to prevent accidental contact with live
parts (e.g. integration in a control cabinet).
Installation:
Connection terminals are located at the top and bottom. To ensure adequate convection,
we recommend a minimum distance of 3cm to other modules above and below the
device. The 24 V voltage supply is connected via the marked screw terminals. The dS485
bus is connected via the in/outputs A and B. Correct polarity (A-A, B-B) is required. The
bi-directional 2-wire bus serves to connect up to 62 dSM. Only one dSS can be connected
per dS485 bus. 120 ohm termination resistors are required for each end of the dS485 bus
cabling. These are included in the packaging. dS485 bus wires must be twisted together.
An optional external push button (IN) at input5 triggers an event which can be configured
in the digitalSTROM configurator. We recommend using an unshielded Ethernet cable.
Caution! Ensure correct polarity of the wires at the dS485 bus (A-A, B-B).
Further information on the commissioning process can be found in the digitalSTROM
installation manual or at www.digitalstrom.org/support.
Guarantee:
aizo ag guarantees fault-free operation of this device according to the specification for 24
months after delivery by aizo ag. Opening the device, other interference with the device, or
incorrect installation/configuration will invalidate the guarantee.
Technical data
Name.........................................................................digitalSTROM-Server
Type designation .......................................................dSS11-1GB
Manufacturer ............................................................aizo ag
Rated input voltage...................................................24VDC (+/- 10%), min. 0.4A
Power consumption without USB.............................max. 2.5W
USB interface............................................................2 x Typ A plug, USB 2.0 Full-Speed,
max. 0.5A @ 5V per port
Ethernet interface.....................................................RJ45 10/100 Mbit/s
Data transfer via dS485 bus......................................dS485 protocol V1.0 / EIA485
Protection..................................................................IP20 EN 60529
Permissible ambient temp. (operation/storage)......-20 °C ...+45 °C/-20 °C ...+70 °C
Permissible humidity (operation).............................in dry rooms only
Weight without packaging.........................................approx. 0.07 kg
LED green........................ normal operational
red ............................ hardware fault
blue-yellow ..............software update
grey ..........................no connection to dS485
Button press for 5sec. ........restart (button below the LED)
press for 15sec. ......reset to factory defaults
(user name/password, DHCP)
Subject to technical modifications. Up-to-date information can be found on our website. Sous réserve de modifications techniques. Vous trouverez les dernières informations sur notre site web.
Con riserva di modifiche tecniche. Le ultime informazioni sono consultabili sulla nostra pagina web.

Popular Server manuals by other brands

NEC Express5800/320Fd-LR user guide

NEC

NEC Express5800/320Fd-LR user guide

IBM x3350 - System - 4192 Product guide

IBM

IBM x3350 - System - 4192 Product guide

Sun Microsystems Sun Netra CP3260 user guide

Sun Microsystems

Sun Microsystems Sun Netra CP3260 user guide

Sony NSS-V2 Operation manual

Sony

Sony NSS-V2 Operation manual

Telvue HyperCaster user manual

Telvue

Telvue HyperCaster user manual

Huawei FusionServer Pro G5500 Routine Maintenance

Huawei

Huawei FusionServer Pro G5500 Routine Maintenance

Supermicro SuperServer 5019A-FTN4 user manual

Supermicro

Supermicro SuperServer 5019A-FTN4 user manual

Dell PowerEdge T610 Hardware installation instructions

Dell

Dell PowerEdge T610 Hardware installation instructions

ABLELink ABLELink SE5002 Series user manual

ABLELink

ABLELink ABLELink SE5002 Series user manual

AIC CB117-OT user manual

AIC

AIC CB117-OT user manual

Overland Storage SnapServer Expansion E2000 quick start guide

Overland Storage

Overland Storage SnapServer Expansion E2000 quick start guide

Cisco UCS C22 Installation and service guide

Cisco

Cisco UCS C22 Installation and service guide

Synology RackStation RS2818RP+ Hardware installation guide

Synology

Synology RackStation RS2818RP+ Hardware installation guide

HP ProLiant MicroServer Installation sheet

HP

HP ProLiant MicroServer Installation sheet

Inspur I48 installation guide

Inspur

Inspur I48 installation guide

Gigabyte G481-HA0-00 Assembly Notice

Gigabyte

Gigabyte G481-HA0-00 Assembly Notice

Lenovo THINKSERVER RS210 warranty and support information

Lenovo

Lenovo THINKSERVER RS210 warranty and support information

DMP Electronics EBOX-3300MX Series user manual

DMP Electronics

DMP Electronics EBOX-3300MX Series user manual

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.